Fast Intentions "Twin Turbo Kit" is here

F.I. Inc. · 01-01-2014, 06:53 PM

Quote:

Originally Posted by phunk

While installing a turbo kit on the 12+, i would do myself a favor and replace pipe #13 with the 09-11 pipe. They are cheap, I think under $50 from courtesy parts?

This would eliminate the need to block off the forward facing pipe, as it does not have that pipe. Just a little bit cleaner is all. Plus, while it is off, you can cut off and weld shut the throttle coolant barb. To eliminate the other end of the throttle coolant, you can pull out the press-in barb on the aluminum rear coolant outlet housing. A 1/8 NPT tap fits in the hole. Put in a stainless 1/8 plug. This is what I did to eliminate the throttle coolant in my car without doing a messy bypass hose. (bypass hose is also allowing some water to bypass radiator after thermostat is fully open, slightly reducing cooling system efficiency)

Doing it this way would be a clean and easy way to cleanup all the coolant line mess. Tested and proven setup in my car for over 2 years daily driven, even in sub zero weather. For a 09-11 this takes care of it. For the 12+ you still need the fast intentions supplied blockoff plate and whatever fittings to attach oil cooler plate in replacement to stock heat exchanger.

Hey buddy, Happy New Year! One problem with eliminating pipe #13 on a 2012+, I circled it in Blue on the picture below. This open barb has a line that goes to the expansion tank. The expansion tank is completely different on the 2012+ so this line has to stay. Technically #12 could go. As shown in the picture below, we opt to cap it instead of removing it. I know that I earlier stated that we would use a block off plate like what comes on the 2009-2011 however I have changed this thinking. It will be too much work for the average person to take #12 off and put a block off plate in it's place due to the driver side exhaust manifold being in the way. We want to simplify the Oil Cooler Kit install as much as possible so we went the other route as shown in the picture below. I have since updated my Oil Cooler Kit picture from post #1700 to reflect the proper parts that will come with a 2012+ Oil Cooler Kit from us.

As for the block off plate, we have 2 applications where it is needed.

Application 1
2012+ 370Z running our Long Tube Headers. As we have found out through installs, pipe #12 interferes with our driver side header sitting flush against the cylinder head. Basically, one of the header tubes makes contact with the line before the header flange mates up. Removing pipe #12 during a Long Tube Header install is a breeze! You now have three choices to make.

1) Remove the 2012+ OEM coolant recirculation system and run nothing.
2) Run an aftermarket Oil Cooler Kit (FI recommended)

Or go with...

Application 2
Below you will see a few pictures that showcase our fix to be able to run the OEM coolant recirculation system and FI Long Tuber Headers. Keep in mind, this only needs to be used in conjunction with our LTH's. Though an Oil Cooler is recommended opposed to this, we wanted to offer a very affordable option. This line comes out of the driver side of the engine block, swoops along the bell housing, underneath the power steering lines and plugs into the back on pipe #9.

Thanks, Tony

F.I. Inc. · 01-02-2014, 01:54 AM

A very Happy New Year to you all and a new product from Fast Intentions. Please follow the link to check out our "official Oil Cooler Kit release"!

Link: ***Fast Intentions Oil Cooler Kit: Official Release***
Website: Fast Intentions

TT Kit related, more updates are coming over the next week. As soon as I can get the dyno charts from Sebastian at SpecialtyZ, I will share them with you. In addition, faceglides installation is going great. Making great progress and becoming more efficient on the install time. dirty_shoeZ kit is still set to ship out this Friday.

Thank you, Tony

hjo1078 · 01-02-2014, 04:37 PM

Quote:

Originally Posted by gbrettin

I want to see the F.I. kit on a fully built motor to handle high boost! ... Anyone planning on doing that in the near future?

that would be me buddy, just patiently waiting on the tt kit for now, no sense in dropping my engine twice so i will wait until i have a comfirmed shipping date from tony before i give my guy the ok to start the build

TerribleONE · 01-02-2014, 07:39 PM

Quote:

Originally Posted by hjo1078

that would be me buddy, just patiently waiting on the tt kit for now, no sense in dropping my engine twice so i will wait until i have a comfirmed shipping date from tony before i give my guy the ok to start the build

Did you decide to do a full build? I am jealous bro!

hjo1078 · 01-02-2014, 07:58 PM

Quote:

Originally Posted by TerribleONE

Did you decide to do a full build? I am jealous bro!

Full build on the way. The delays helped me gather more funds to go all out bro. And by the way. I think im more jealous of you right now.

TerribleONE · 01-02-2014, 07:59 PM

Quote:

Originally Posted by hjo1078

Full build on the way. The delays helped me gather more funds to go all out bro. And by the way. I think im more jealous of you right now.

You are gonna spank that GTR

hjo1078 · 01-02-2014, 08:15 PM

Quote:

Originally Posted by TerribleONE

You are gonna spank that GTR

That was the plan all along. Haha

phunk · 01-02-2014, 08:23 PM

Good info tony, I was not considering what else about that pipe may be different on the 2012+. In that scenario, I would do what I did to my 350z, and just cut that pipe off and weld a plug in it!

F.I. Inc. · 01-05-2014, 08:27 PM

Update,

FINALLY...Here it is, our Complete Twin Turbo Kit for the Nissan 370Z showcased in full. This picture clearly shows the full depth of what goes in to each and every kit. No corner cut and no detail forgotten!

Thank you, Tony

SPOHN · 01-05-2014, 08:33 PM

It's missing something big though?

On my car.

F.I. Inc. · 01-05-2014, 08:44 PM

Quote:

Originally Posted by SPOHN

It's missing something big though?

On my car.

Chris,

I know that you will always keep us in mind. When the sting wears off, give us a call!

Thanks, Tony

cycy89 · 01-05-2014, 08:55 PM

7AT upgrade kit next?

Sent from my SGH-M919 using Tapatalk

F.I. Inc. · 01-05-2014, 09:06 PM

Oh, I almost forgot...

dirTy_ShoeZ kit is boxed up and ready to ship...Tomorrow!

We also have a few big announcements to make. Stay tuned...

Thanks, Tony

F.I. Inc. · 01-05-2014, 09:08 PM

Quote:

Originally Posted by cycy89

7AT upgrade kit next?

Sent from my SGH-M919 using Tapatalk

I will send you some pictures of the TT Kit progress on your car in the next few weeks. Flex Plate, Valve Body Upgrade and Trans. Cooler are in the works as well.

Thanks, Tony

Cell · 01-05-2014, 09:08 PM

Quote:

Originally Posted by F.I. Inc.

Oh, I almost forgot...

dirTy_ShoeZ kit is boxed up and ready to ship...Tomorrow!

We also have a few big announcements to make. Stay tuned...

Thanks, Tony

So beautiful...

01-02-2014, 01:54 AM	#1727 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	A very Happy New Year to you all and a new product from Fast Intentions. Please follow the link to check out our "official Oil Cooler Kit release"! Link: *Fast Intentions Oil Cooler Kit: Official Release* Website: Fast Intentions TT Kit related, more updates are coming over the next week. As soon as I can get the dyno charts from Sebastian at SpecialtyZ, I will share them with you. In addition, faceglides installation is going great. Making great progress and becoming more efficient on the install time. dirty_shoeZ kit is still set to ship out this Friday. Thank you, Tony fuct, XwChriswX, hjo1078 and 1 others like this. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION" Last edited by F.I. Inc.; 01-02-2014 at 01:59 AM.

01-02-2014, 08:23 PM	#1733 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,668 Drives: 370 Rep Power: 974723	Good info tony, I was not considering what else about that pipe may be different on the 2012+. In that scenario, I would do what I did to my 350z, and just cut that pipe off and weld a plug in it! F.I. Inc. and djtodd like this. __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph

01-05-2014, 08:27 PM	#1734 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	Update, FINALLY...Here it is, our Complete Twin Turbo Kit for the Nissan 370Z showcased in full. This picture clearly shows the full depth of what goes in to each and every kit. No corner cut and no detail forgotten! *Thank you, Tony* fuct, XwChriswX, puckshaw and 15 others like this. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION"

01-05-2014, 08:33 PM	#1735 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 46 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	It's missing something big though? On my car. F.I. Inc. and XwChriswX like this. __________________

01-05-2014, 08:55 PM	#1737 (permalink)
cycy89 A True Z Fanatic Join Date: Jun 2011 Location: 120mph somewhere Posts: 1,097 Drives: #TTURBOZ Rep Power: 30	7AT upgrade kit next? Sent from my SGH-M919 using Tapatalk F.I. Inc. likes this. __________________ Fast Intentions Twin Turbo Kit GT2860RS, 677WHP\|FI 34 row oil cooler\|F.I. CBE\|Fast 500E return fuel system\|FI trans cooler\|FI billet aluminum flex plate\|Excedy clutch packs\|ENKEI RP03\|BC BR coilovers\|SEIBON Carbon\|EVO-R Rear fog light\|GTR push start\|Whiteline sway bars, Diff bushing\|DSS axles\|ECUTekW/FlexFuelTune

01-05-2014, 09:06 PM	#1738 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	Oh, I almost forgot... dirTy_ShoeZ kit is boxed up and ready to ship...Tomorrow! We also have a few big announcements to make. Stay tuned... Thanks, Tony fuct, Cell, Presto and 3 others like this. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION"

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fast Intentions 3" (Twin Turbo) exhaust is here!	F.I. Inc.	Intake/Exhaust	91	02-08-2017 06:09 AM
Fast Intentions "Twin Turbo Kit" Official Release	F.I. Inc.	Drivetrain/Engine	95	11-20-2014 12:38 AM
Twin Turbo vs. Single Turbo V6: A Dissertation	Mike@GTM	Forced Induction	115	08-14-2014 10:04 PM
Twin scroll vs twin turbo	SS_Firehawk	Forced Induction	32	04-13-2014 01:02 PM
GTM Motorsports Twin Turbo vs Greddy Twin Turbo Kit	Nismo221	Forced Induction	57	08-16-2011 05:44 PM

*****Fast Intentions "Twin Turbo Kit" is here*****

Fast Intentions "Twin Turbo Kit" is here