Stillen SC Build 500 WHP?

Mr.Squeeze

You would have to copy my cog set up ANMVQ and a few other's have copied it already.The boost will come on a lot sooner with it you will have a better powerband with the cog pulleys.

__________________
Driven Motorsports Single Turbo 7675 T4 1.32 A/R 995WHP 780TQ

Nissan370

ok i am still having trouble understanding why the 9lb pulley is so small
the v3 can crank out up to 17psi and if its using a small pulley to start then what pulley is going to give me 15-16psi or close to that
i mean theres like what only one pulley smaller then 2.75

i know our heads flow well but i mean with the v2 and 2.95pulley i was seeing close to 550rwhp and 13.5psi on my mustang
i will figure it out i guess

__________________
370z vsr motorsports single turbo/built motor 9.1cr 525rwhp/450rwtq @ 10.5psi (stock maf maxed out)

Mr.Squeeze

The pulleys that Stillen use on the back of the blower and Jack shaft are big this slows the blower down.This is the reason why people have a problem making torque and Hp with the blower. The Stock pulley that comes with the kit is 3.12 that's not small at all either.

This is the reason why I put cog pulleys when I had the Stillen kit because I knew the blower was spinning slow. It is also the reason I made 465 Whp 360 TQ on a dynojet with the bigger pulley that came with the kit. The only way to get the blower to even try to crank out more psi is to use the cog pulleys that I used. But doing so you have to change a bunch of other things with the kit that have been talked about already.

I hope this helps you understand better.

__________________
Driven Motorsports Single Turbo 7675 T4 1.32 A/R 995WHP 780TQ

ANMVQ

+1 for what Mr.Squezze said, You can change the cogs upgrade the impeller to make more boost and sooner, But you HAVE to change the MAF's ( You will run out at 6500), You also will have to upgrade the injectors-the Stillen 600CC's wont cut it, and you will have to shave part of the head( Idler is going to hit it). An after all of that we still dont know what WHP you will make, My car has not hit the dyno yet. Mr.Squeee made 465 and ran out of MAF, I'm hoping to make 20 more WHP then he did. He was also @ 11PSI with TP's I have stock cats so I'm proablly going to see + 2 PSI. I also changed the Heat exchanger and the BPV.. As soon as my car hits the dyno and I get the numbers from my tune I will out them up on here. Should be tomorrow I hope.. I havent seen my car for going on 10 weeks.

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

EVOHUNTER

Is it worth getting the impeller and shims from 928 motor sports? or just do the cog set up?

__________________

ANMVQ

just got a call, Fingers crossed for the dyno tune this afternoon.

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

ANMVQ

The Impeller works, I read a ton of stuff on it, Mr.Sqeeze made power with it and the cog set up, Not sure how much soon the PSI comes in but the 360 WTRQ is nice, I got mine from Vortec cause it was there for the warranty work.

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Osiris

i didn't need to upgrade my maf's or injectors.

__________________

^^^^^^^^^Like our Facebook!^^^^^^^^^

ANMVQ

With the cog and impeller upgrade? Squezze did, Ran out of MAF @6500. The injectors will work but 90-95% duty cycle. Maybe one of the other guys will chime in on the duty cycle also.

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Osiris

i did the cogs, but not the impeller.

__________________

^^^^^^^^^Like our Facebook!^^^^^^^^^

EVOHUNTER

My maf's should be fine, because im going air to air.. injectors... hhmm..
i forgot about those.. theres another 500 bucks lol, Anmvq, what CC and brand did u go with? Im going to sasha's at 9 am, sunday morning. Really looking forward to this, aswell as your numbers anmvq.

__________________

ANMVQ

Yea I was told if you move the MAF"s back you should be ok too, The injectors I got are the Boch EV14's 850 CC's

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

indyn

Looking forward to your mod with the Stillen setup. I do like the idea of air to air intercooler on stock IM with Stillen s/c.
ANMVQ, hopefully good results buddy.

ANMVQ

Maybe with the cogs +2 PSI you are ok? The impeller should be another 2 PSI and boost comes in sooner in the RPM band and more PSI then also, I was reading over on the Cobra forums, Guys were seeing double the boost at 3k, " Say they where seeing 3 PSI @3k after the did the impeller they woud see 6PSI at the same 3k"

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

ANMVQ

Thanx man, I hope so too.


If he gets very good results on the Air-Air might be something I look at over the winter, I may Stay with the Stillen Intake tho.

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,