Stillen SC Build 500 WHP?

Osiris

I'll post whp once i get it on a dynojet, right now i only have numbers from a mustang dyno that runs unusually conserative, they say it runs 20% lower than dynojet.

__________________

^^^^^^^^^Like our Facebook!^^^^^^^^^

ANMVQ

Come on man, Those are "REAL" My numbers are on a mustang,

At least to me dynojets are inflated number, Just IMO

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Osiris

ok fine, 391WHP / 308WTQ

The tune i have, and i quote my tuner, is a "safe" tune, so if settings were tweaked they could get more out of it but would put me on the edge of the safe zone

EDIT: plus it's hot as balls down here!!

__________________

^^^^^^^^^Like our Facebook!^^^^^^^^^

ANMVQ

looks about right. Thanx,
Same as what I made,

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

ANMVQ

This whole thing is now on hold, LONG STORY

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Nissan370

I don't know how to compare the cog setup to the pulley set up

Like what cog numbers = 3.12 or 2.95 ect
Or what's the smallest you can go on the cog set-up I want 15-16psi once all is said and done

I should not us psi I guess let's just say I want a good 500 to the wheel


And what happen why it's on hold

__________________
370z vsr motorsports single turbo/built motor 9.1cr 525rwhp/450rwtq @ 10.5psi (stock maf maxed out)

Osiris

although the blower can handle higher psi, the intercooler is not adequate to disapate heat above 12psi. If you want the cogged pulley part numbers i can send them to you. But be advised, it's not as simple as removing the old ones and putting these on. it may require some customization like spacers and small adjustments in addition to requiring a re-tune.

__________________

^^^^^^^^^Like our Facebook!^^^^^^^^^

fahkyotech

Man i just read this entire thread ..i was hoping to see the outcome and base my decision on whether or not to go FI off of your results

ANMVQ

For the reasons why Osiris said the Dealer can not figure out how to set up the pulleys there was alot of back and forth between them and I , Pics and what not, There are saying the belt wants to walk off??? Idler has to not be set up right and they did not install the heat exchanger( Said they cant) so I'm going to pick the car up today and either finish myself ( Which I should be able to) or send it to my tuners on Next Friday VIA tow truck, I just how I can drive the car home, 45 Mins ?

Pretty much not a happy person right now,

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Mr.Squeeze

The stock Stillen pulley is 3.12 the smaller pulley 9 pound you have is 2.75 that's pretty small. That's the reason I did the cog pulleys when I had the kit better grip plus boost comes on sooner ,even better than the 9 pound pulley . Since you have the T trim you would need to switch in order to take advantage if the blower it self . The thing that concerns me with doing this is all the other mods you have to do to the kit I it runs hot . This is the reason I sold mine with my built motor .

__________________
Driven Motorsports Single Turbo 7675 T4 1.32 A/R 995WHP 780TQ

WILD370Z

I fully understand i called stillen and they said they didnt know the pulley size which i find hard to believe. its not hard to measure one that is not on a car

__________________
Custom yellow respray-custom interior-lights-20 inch wheels-x force full exaust-stillen sc-928 impeller-carbonetics 2.0 differential-34 row oil cooler-auto cooler-2.8 pulley up grade

ANMVQ

Sounds like them. Wouldnt tell me anything either, Car went to my tuners on Friday night on a flat bed. Should have something this week,. :/

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

Boosted Performance

The pulleys available will be:

2.62"
2.87"
3.12"
3.25"
3.33...ect

These are right from Vortech, so unless it is a custom pulley, it won't be 2.75".

Also, looking at the spec/flow of the V3 supercharger 500whp+ should be no problem at all with an air/air FMIC. I would get rid of the Stillen water/air cooling system and go back to the OEM plenum. That way you can put the MAF sensor in the proper location, and have a solid S/C kit capable of solid power.


A quick search...

Stillen uses a Vortech V3 head unit: 1150cfm (for an Si, and 1050cfm for the SCi)
GTM Stage II uses a Rotorex 38-91: 1075cfm (I think advertised as Stage II 600hp)

So an educated guess suggests that with the air/air FMIC mod, the Stillen kit would make 600hp. At least this time Stillen picked a good supercharger to start with vs. the horrible decision they made with the 350z.

__________________
750WHP starting @ $7,500 to the door
FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html
FB: https://www.facebook.com/Boosted-Per...6303179791462/
IG @boostedperformanceyeg

ANMVQ

Thanx for the info, I'm sure you guys are working on something ???

__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,

EVOHUNTER

I havent had time to go see sasha yet, My business is been balls to walls for the last 3 weeks. Its only going to get worse, as our weather is changing and everyone wants newtires/winter tires put on.

Sasha, hows sunday looking for you? you busy?

__________________