GTM Performance Engineering: Project Nismo S/C Extreme

SAM@GTM

The owner of this fine Nismo we proudly present to you today sent us his showroom stock car with the intent of having a complete transformation performed right out the gate. With all the expertise of our team, we were able to put together a complete package that addresses every aspect of the car while leaving the clean lines of the factory Nismo body work unmarred.

Here is the list of upgrades:

GTM Stage 1.5 Supercharger Kit (550bhp)
GTM 2.5" Test Pipes
HKS Hi-Power Cat-back exhaust
Aquamist HFS-4 Water/Methanol Injection System
GTM 70mm Competition Radiator
GTM Thermostatic Oil Cooler Supplement Kit and Oil Cooler
GTM Vented Fender Liner
OS Giken Twin Disk Clutch Kit
Heavy Duty Concentric Slave Cylinder for OS Giken Clutch
HKS CAMP2
KW Variant 3 Coilovers
Hotchis Sway Bar Kit
SPC Camber Kit
GTM Plug and Play Traction Control System
Work Gnosis Wheels
Michelin Pilot Super Sport Tires


Results

At the heart of this beast, we have our Stage 1.5 Supercharger Kit that combines the responsiveness and mid-range torque of our Stage 1 Supercharger Kit with the massive airflow afforded by our Stage 2’s compressor inlet design. This delivers a torque curve that comes on hard in the midrange and stays flat all the way to redline. With the water/methanol injection system at full tilt and 93 octane gas, we were able to pump out 507whp and 359wtq. Looking at the dyno graph, you can see that 90% of peak torque is available from 3900rpm to its 7500rpm redline.


Featured Components

Below are all the major components that went into this build.

SAM@GTM

Keeping fluid temperatures under control is our GTM 70mm Competition Radiator and fan shroud to reuse the factory fans along with our 25 row competition engine oil cooler and thermostatic supplement kit. Our vented fender liner helps evacuate air from the oil cooler to increase its efficiency as well.


On the drivetrain side of things, we employed the smooth driving characteristics and exceptional clamping abilities of the OS Giken Twin Disk clutch along with a heavy duty concentric slave cylinder for the OS Giken Clutch.


To keep detonation at bay and allow for more advanced timing is the Aquamist HFS-4 with our 5 nozzle setup. There's one nozzle before the intercooler, one in each pipe after the intercooler and one in each MAF pipe between the MAF sensor and throttle body.

SAM@GTM

Exhaust System Installation

Expelling spent exhaust gasses is a set of our GTM 2.5" Test Pipes and an HKS Hi-Power Cat-back exhaust. This exhaust setup has an aggressive sound to complement the raw power this car throws down.

Engine Monitoring System Installation

We installed a second monitor in the factory cubby to allow for the HKS CAMP2 to display all the engine vitals separate from the navigation system we installed in the factory radio’s double DIN slot. In addition to displaying OBDII channels, we installed several sensors: Oil Pressure, Exhaust Gas Temperature, and Fuel Pressure. We also installed a backup camera to help the driver compensate for the Z's blind spots as you back out.

Traction Control System Installation

With 500whp on tap, it is easy to get the car to step out under power. Therefore, to keep the tail in check, this car has our GTM Plug and Play Traction Control to cut power incrementally to combat wheelspin without the bogging the factory VDC causes. With end user adjustability, the traction control system allows for full opposite lock drifts without losing control or on the other end of the spectrum, stomping on the accelerator in soaking wet weather and hooking up to walk away from the competition.

Wheels, Tires, and Suspension

Belting out 500whp begs for wider tires to get it to the ground. Standing up to that task are a set of Michelin Pilot Super Sport tires in 275/35R19 up front and 305/30R19 out back wrapped around a clean set of Work Gnosis GS2 wheels spec’d by GTM to 19x10” ET30 up front and 19x11” ET18 out back. To keep the car planted in the turns, we installed a set of nicely valved KW variant 3 coilovers and Hotchkis sway bars. With our GTM Precision Laser Alignment and SPC Camber Kit, we were able to dial in the suspension settings to ensure maximum cornering grip without undue tire wear. Last but not least, we upgraded the stopping power as well with Stoptech cross-drilled rotors, GTM braided stainless lines, and Motul RBF600 DOT 4 Racing Brake fluid to stave off brake fade. To finish things off, our GTM Powdercoated Calipers give the braking system a sportier appearance.

SAM@GTM

Completed Project

Power, poise, and presence are the underlying themes for this build and complement the philosophy behind the OE design while taking it all to the next level.

BG370z

Wow.........that is super clean
Nice job GTM!!

Nixlimited

Nom nom nom.

__________________
Car Sold! Pleasure being a part of the Z community.
New ride: 2015 GT-R - 647 WHP / 641 WTQ (e85) & 543 WHP / 519 WTQ (91)

Shamu

Just a safety warning about SPC rear camber arms. Mine sheered off on track. Not overextended etc. SPC bend arm where it's threaded and they sheer off under stress. sPL is better choice for quality build where high stress is anticipated.

Grand am team wouldn't reinstall them on my car after that incident.


That's a cute boulevard cruiser though.

__________________
Grant

BigT

Wow, that is soo amazing. I really wish I had the funds to do something like this. And, GTM is exactly the place I would do it too.

CorbinDallas

I am literally speechless!! Wish I had the funds to build my car this way. Awesome awesome work GTM.

Footloose301

$30k?

__________________

2010 40th Anniversary 370Z

Jordo!

Did I see a temp probe in the header? Measuring EGT's to get an idea how well the water injection is doing?

__________________
Enjoy it. Destroy it.

Viera

Absolutely stunning. Such a beautiful car with some tasty mods :P Great job, GTM!

__________________

BigT

Measuring EGT's is great for water injection, but just a good tool in tuning, period. Just because you're not knocking or pinging at a certain AFR, doesn't mean its optimal for your engine. EGT's can help get your tune more precise. Even with timing advance.

Liquid_G

wtf this car is in Illinois? How come I've never seen it before?

__________________

tanamerra

Nice ride.

__________________
2010 370Z Nismo
Motordyne M370, Injen cai, HKS cbe,
Uprev, Work wheels, Radi-Cal brake kit