Supercharger vs VR30 swap for my 370z Nismo

Mr.K · 10-31-2021, 05:29 PM

Hello community, sorry for the long post LOL. I know there have been many threads about turbo vs supercharger but this thread isn't in regards to that. I'm looking for more power out of the Z34 chassis. Now my question is in regards to keeping the weight distribution of the chassis balanced. The VR30 would be the obvious choice here as it is only 18lbs more than the VQ37 but it looses some of what makes the VQ37 great with it's high redline, iconic exhaust note and reliability. A supercharger kit weighs around 85lbs according to some sources but I believe in a thread a member stated a net gain of about 30lbs. How could I drop the weight up front (more specifically from the internals) to offset the weight of a supercharger? I have already considered battery relo, dry carbon parts, wheels, tires, etc. My goal is too keep the overall weight of the car low, improve its front/rear weight distribution and make over 450hp. I just wanted to know if my goals would be realistically possible with a supercharger otherwise I'll probably be doing a VR30 swap

.

HapaZ · 10-31-2021, 10:20 PM

I'd say an engine swap to save less than 50lbs is a smart way to go so go do that. You'll definitely notice the difference. Just take pictures along the way!

Spooler · 10-31-2021, 10:21 PM

Not sure how you would get it to pass smog inspection in Cali with a VR30.

Jhill · 10-31-2021, 10:37 PM

Definitely won’t pass smog in Ca. But then again if putting this much effort for weight distribution I’m hoping it’s not a street car anyway as the little bit of difference between vq37 and vr30 you’ll never notice the difference on a street driven car. And if going full blown race car then just add oil coolers and such to the back of the car to regain the balance.

redondoaveb · 10-31-2021, 11:05 PM

You can do an engine swap and pass smog CARB if the engine you're installing is out of a newer car than the chassis that it's going in and retains the original smog equipment (including cats) that that are required for that engine. Of course it would have to go through CARB testing and that could be extensive and expensive. There's a company that does LS3 swaps in Miata's that meet CARB standards.

Mr.K · 11-01-2021, 04:29 AM

Quote:

Originally Posted by redondoaveb

You can do an engine swap and pass smog CARB if the engine you're installing is out of a newer car than the chassis that it's going in and retains the original smog equipment (including cats) that that are required for that engine. Of course it would have to go through CARB testing and that could be extensive and expensive. There's a company that does LS3 swaps in Miata's that meet CARB standards.

That is correct, which is why I figured the VR30 swap would also work in my favor. It costs less that $50 to get the car smog legal by taking it to a referee station and getting it approved with a BAR sticker. So it is definitely doable here in Cali. In regards to the other members the car would be a street car AND be seeing track days and maybe drag strips. I know some might argue the power increase might not be useful on the street but a nice torque jump is something I think definitely would be

The rotrex supercharger that was just released seems like a very nice choice if it wasn't for the weight. Anyone know how much the net weight gain is with the kit and how much weight I can drop from the engine itself (forged internals)??

TopgunZ · 11-01-2021, 08:59 AM

If your talking about a built VQ, then throwing a Rotrex on there is going to blow the power to weight ratio out of the water over a VR swap.

Elmo370z · 11-01-2021, 10:07 AM

Quote:

Originally Posted by Mr.K

Hello community, sorry for the long post LOL. I know there have been many threads about turbo vs supercharger but this thread isn't in regards to that. I'm looking for more power out of the Z34 chassis. Now my question is in regards to keeping the weight distribution of the chassis balanced. The VR30 would be the obvious choice here as it is only 18lbs more than the VQ37 but it looses some of what makes the VQ37 great with it's high redline, iconic exhaust note and reliability. A supercharger kit weighs around 85lbs according to some sources but I believe in a thread a member stated a net gain of about 30lbs. How could I drop the weight up front (more specifically from the internals) to offset the weight of a supercharger? I have already considered battery relo, dry carbon parts, wheels, tires, etc. My goal is too keep the overall weight of the car low, improve its front/rear weight distribution and make over 450hp. I just wanted to know if my goals would be realistically possible with a supercharger otherwise I'll probably be doing a VR30 swap

.

Dry sump, lower the center of gravity and push the engine back far as possible. If you’re really serious about weight distribution.

JARblue · 11-01-2021, 10:43 AM

Quote:

Originally Posted by Mr.K

Now my question is in regards to keeping the weight distribution of the chassis balanced.

How serious are you on the track? Because it sounds like you're looking to spend a lot of time/money trying to fix a problem that isn't really a problem.

I definitely would not use weight distribution as the deciding factor on whether to go SC or VR30. There are far more relevant factors.

takemorepills · 11-01-2021, 11:49 AM

If I were inclined to do a VR30 swap, I'd wait for the new Z to come out, get wrecked and buy a donor 6MT car and swap the entire engine, 6MT, ECU, IPDM, EPS, keyless system over.
That way you'd have a fully sorted car that complies with the latest emission requirements.
Currently the only donor for a VR30 is the 7AT-only Infiniti Q cars. I haven't seen a fully-sorted VR30 swap yet. I know there are some good running swaps, but they don't have EPS (no provisions for hydraulic PS on VR30 AFAIK) so they don't have power steering, and I know that the ECU isn't intended for a 6MT car.

Rusty · 11-01-2021, 12:31 PM

Doing a VR swap sounds nice but...........Your car will be down longer than you think. Getting everything sorted out. Going with the SC, you could pound it out in a week. You won't notice the extra weight, believe me. Some trackrats have been bolting down lead weight in the rear to balance out the car. There is no way to remove enough off the front to balance it to 50/50 unless you move the engine back 8".

Mr.K · 11-01-2021, 01:28 PM

Quote:

Originally Posted by Elmo370z

Dry sump, lower the center of gravity and push the engine back far as possible. If you’re really serious about weight distribution.

I did consider this option at one point but found that the associated costs and downsides were not in line with the goal of my car build.

Mr.K · 11-01-2021, 01:42 PM

Quote:

Originally Posted by JARblue

How serious are you on the track? Because it sounds like you're looking to spend a lot of time/money trying to fix a problem that isn't really a problem.

I definitely would not use weight distribution as the deciding factor on whether to go SC or VR30. There are far more relevant factors.

You are right in saying that the issue I'm having isn't really a "problem". I don't think I would ever take my car to be a serious track machine as I would be getting rid of a lot of creature comforts as I still want it to be streetable, but the way I see it is if it can be improved in some way then that is a plus in my book.

Quote:

Originally Posted by takemorepills

If I were inclined to do a VR30 swap, I'd wait for the new Z to come out, get wrecked and buy a donor 6MT car and swap the entire engine, 6MT, ECU, IPDM, EPS, keyless system over.
That way you'd have a fully sorted car that complies with the latest emission requirements.
Currently the only donor for a VR30 is the 7AT-only Infiniti Q cars. I haven't seen a fully-sorted VR30 swap yet. I know there are some good running swaps, but they don't have EPS (no provisions for hydraulic PS on VR30 AFAIK) so they don't have power steering, and I know that the ECU isn't intended for a 6MT car.

If I were to go with the VR30 swap route, I would be doing something like this. Mainly because the new revised VR30 has changes that make it more suitable for better performance and all the original issues with wiring would be sorted out.

Quote:

Originally Posted by Rusty

Doing a VR swap sounds nice but...........Your car will be down longer than you think. Getting everything sorted out. Going with the SC, you could pound it out in a week. You won't notice the extra weight, believe me. Some trackrats have been bolting down lead weight in the rear to balance out the car. There is no way to remove enough off the front to balance it to 50/50 unless you move the engine back 8".

Yes the downtime is something to think about, but it wouldn't be a deciding factor for me as I have other means of transportation. Although I do want to say that I am NOT looking to achieve a 50/50 ratio as it would require a lot more money and more weight added and would just be unrealistic. I would be looking for something closer to 52/48 distribution but I would have to increase the overall weight of the car and depending on which route I take I would be adding either something like 60lbs or something like 180lbs to offset the weight at the front.

Mr.K · 11-01-2021, 01:58 PM

Quote:

Originally Posted by TopgunZ

If your talking about a built VQ, then throwing a Rotrex on there is going to blow the power to weight ratio out of the water over a VR swap.

I have been lurking in the other thread on here on your rotrex kit and up until that point I have not seriously considered a supercharger kit but after seeing dyno sheets and improvements I was very happy with the way the torque curved looked. I know that from the beginning of your development you wanted the kit to be CARB legal, how far along are you on this process?

TopgunZ · 11-01-2021, 02:26 PM

Quote:

Originally Posted by Mr.K

I have been lurking in the other thread on here on your rotrex kit and up until that point I have not seriously considered a supercharger kit but after seeing dyno sheets and improvements I was very happy with the way the torque curved looked. I know that from the beginning of your development you wanted the kit to be CARB legal, how far along are you on this process?

Honestly, pretty far. I wouldnt hold your breath on that. I am already getting lots of attention on the Q50 turbo kits so that will keep us busy and Ive been eyeballing a new platform to get into.

Im not saying I wont do it, I am just unsure of when I will.

10-31-2021, 05:29 PM	#1 (permalink)
Mr.K Base Member Join Date: Mar 2021 Location: California Posts: 79 Drives: 2017 370z Nismo Rep Power: 4	Supercharger vs VR30 swap for my 370z Nismo Hello community, sorry for the long post LOL. I know there have been many threads about turbo vs supercharger but this thread isn't in regards to that. I'm looking for more power out of the Z34 chassis. Now my question is in regards to keeping the weight distribution of the chassis balanced. The VR30 would be the obvious choice here as it is only 18lbs more than the VQ37 but it looses some of what makes the VQ37 great with it's high redline, iconic exhaust note and reliability. A supercharger kit weighs around 85lbs according to some sources but I believe in a thread a member stated a net gain of about 30lbs. How could I drop the weight up front (more specifically from the internals) to offset the weight of a supercharger? I have already considered battery relo, dry carbon parts, wheels, tires, etc. My goal is too keep the overall weight of the car low, improve its front/rear weight distribution and make over 450hp. I just wanted to know if my goals would be realistically possible with a supercharger otherwise I'll probably be doing a VR30 swap .

10-31-2021, 10:20 PM	#2 (permalink)
HapaZ Base Member Join Date: Sep 2014 Location: NorCal Posts: 245 Drives: 2012 370z Base Coupe Rep Power: 11	I'd say an engine swap to save less than 50lbs is a smart way to go so go do that. You'll definitely notice the difference. Just take pictures along the way! Mr.K likes this.

10-31-2021, 10:37 PM	#4 (permalink)
Jhill Track Member Join Date: Mar 2016 Location: San jose Posts: 854 Drives: 2013 370z sport Rep Power: 3384	Definitely won’t pass smog in Ca. But then again if putting this much effort for weight distribution I’m hoping it’s not a street car anyway as the little bit of difference between vq37 and vr30 you’ll never notice the difference on a street driven car. And if going full blown race car then just add oil coolers and such to the back of the car to regain the balance. Rusty likes this.

10-31-2021, 11:05 PM	#5 (permalink)
redondoaveb A True Z Fanatic Join Date: Apr 2017 Location: So. Commiefornia Posts: 6,361 Drives: 2014 Nismo Gunmetal Rep Power: 2684374	You can do an engine swap and pass smog CARB if the engine you're installing is out of a newer car than the chassis that it's going in and retains the original smog equipment (including cats) that that are required for that engine. Of course it would have to go through CARB testing and that could be extensive and expensive. There's a company that does LS3 swaps in Miata's that meet CARB standards. __________________ Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp Last edited by redondoaveb; 10-31-2021 at 11:12 PM.

11-01-2021, 08:59 AM	#7 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	If your talking about a built VQ, then throwing a Rotrex on there is going to blow the power to weight ratio out of the water over a VR swap. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

10-31-2021, 10:21 PM	#3 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,803 Drives: 2013 Nismo 370z Rep Power: 2684392	Not sure how you would get it to pass smog inspection in Cali with a VR30.

11-01-2021, 11:49 AM	#10 (permalink)
takemorepills Base Member Join Date: Apr 2019 Location: Seattle, WA Posts: 196 Drives: Q60 3.7 AWD Rep Power: 6716	If I were inclined to do a VR30 swap, I'd wait for the new Z to come out, get wrecked and buy a donor 6MT car and swap the entire engine, 6MT, ECU, IPDM, EPS, keyless system over. That way you'd have a fully sorted car that complies with the latest emission requirements. Currently the only donor for a VR30 is the 7AT-only Infiniti Q cars. I haven't seen a fully-sorted VR30 swap yet. I know there are some good running swaps, but they don't have EPS (no provisions for hydraulic PS on VR30 AFAIK) so they don't have power steering, and I know that the ECU isn't intended for a 6MT car. JARblue, Rusty and Mr.K like this.

11-01-2021, 12:31 PM	#11 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,189 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Doing a VR swap sounds nice but...........Your car will be down longer than you think. Getting everything sorted out. Going with the SC, you could pound it out in a week. You won't notice the extra weight, believe me. Some trackrats have been bolting down lead weight in the rear to balance out the car. There is no way to remove enough off the front to balance it to 50/50 unless you move the engine back 8". JARblue, TopgunZ, Elmo370z and 1 others like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
What do we know about the VR30?	BrandonT	Nissan 400Z Engine and Drivetrain	9	06-07-2022 05:45 PM
VR30 Swapped 370z	rayZinbrand	Member's 370Z Gallery	60	09-17-2021 07:35 PM
Main Instrument Gauge (Combination meter) Swap to 2017 Nismo Gage Swap	shika805	DIY Section (Do-It-Yourself)	5	10-28-2020 08:35 PM
2015 370z NISMO 7AT Stillen Supercharger	bernbad89	Nissan 370Z General Discussions	3	02-06-2016 05:15 PM
370Z nismo Emblem swap pics	street2soul	Nissan 370Z Photos / Spyshots / Video / Media Gallery	3	10-19-2013 05:03 PM