Vortech V3 failure

redondoaveb · 10-20-2020, 01:20 PM

If you don't want your oil slinger to look like this, don't over spin your V3.

Hotrodz · 10-20-2020, 02:30 PM

Oh my! Is this yours?

Sent from my SM-G965U using Tapatalk

redondoaveb · 10-20-2020, 02:42 PM

Quote:

Originally Posted by Hotrodz

Oh my! Is this yours?

Sent from my SM-G965U using Tapatalk

My old one. The V3's don't like to be over spun I found out. I always thought the bearings failed from over spinning. Come to find out it's the oil slinger. They're just laser tack welded on to the shaft and the welds break under really high rpm. It then starts slinging itself.

*J*ap***V*et* · 10-20-2020, 03:03 PM

😳😳😳😳

TopgunZ · 10-20-2020, 03:04 PM

Yes but define "overspun". I know you are going into warp mode with yours. Lets not confuse guys in thinking taking it up a few K past limit is going to result in catastrophic melt down.

redondoaveb · 10-20-2020, 03:28 PM

Quote:

Originally Posted by TopgunZ

Yes but define "overspun". I know you are going into warp mode with yours. Lets not confuse guys in thinking taking it up a few K past limit is going to result in catastrophic melt down.

They're rated at 52000 rpm. Vortech used to state that they could be run up to 55000 safely. They have since retracted that and they recommend that they not exceed the 52000 rpm limit.

Rusty · 10-20-2020, 03:41 PM

What's the slinger made of? Brass or steel? What I found with the brass slingers on other equipment. Is that if they get a worn spot on the inside. When the equipment stops and the slinger comes to rest. If it rests on that worn spot. When the equipment is restarted. The slinger will NOT spin with the shaft. The other thing is if the slinger is out of round. The same thing happens. With either brass or steel.

redondoaveb · 10-20-2020, 03:49 PM

Quote:

Originally Posted by Rusty

What's the slinger made of? Brass or steel? What I found with the brass slingers on other equipment. Is that if they get a worn spot on the inside. When the equipment stops and the slinger comes to rest. If it rests on that worn spot. When the equipment is restarted. The slinger will NOT spin with the shaft. The other thing is if the slinger is out of round. The same thing happens. With either brass or steel.

I'm pretty sure it's steel, I'm not sure if it's stainless. It's basically tack welded to the shaft. The oil slinger is their most common failure point.

Rusty · 10-20-2020, 04:21 PM

Quote:

Originally Posted by redondoaveb

I'm pretty sure it's steel, I'm not sure if it's stainless. It's basically tack welded to the shaft. The oil slinger is their most common failure point.

Never seen one that's tack welded to the shaft.

You sure it didn't weld it's self to the shaft?

redondoaveb · 10-20-2020, 05:49 PM

Quote:

Originally Posted by Rusty

Never seen one that's tack welded to the shaft.

You sure it didn't weld it's self to the shaft?

Straight from the email I received from vortech. I then talked to another shop that verified it.

"The gear sets are matched sets, the oil slinger is welded to the shaft, so it can’t just be replaced by itself"

Leingod · 10-20-2020, 06:24 PM

Meh. Jar will still buy it if you post it in the for sale section.

redondoaveb · 10-20-2020, 06:49 PM

Quote:

Originally Posted by Leingod

Meh. Jar will still buy it if you post it in the for sale section.

Nothing a little JB Weld can't fix.

I'll post it up when vortech sends my blower back. Probably have a couple bad bearings he might be interested in also

TopgunZ · 10-20-2020, 07:35 PM

Quote:

Originally Posted by redondoaveb

They're rated at 52000 rpm. Vortech used to state that they could be run up to 55000 safely. They have since retracted that and they recommend that they not exceed the 52000 rpm limit.

But weren't you taking yours to like 72,000?

redondoaveb · 10-20-2020, 07:54 PM

Quote:

Originally Posted by TopgunZ

But weren't you taking yours to like 72,000?

62700. But still way over what it was rated for. The only reason I pushed it that hard was because I had the upgraded 928 ceramic bearings and I thought the bearings were what failed at high rpm. If I had known that it was the oil slinger that's prone to failure at high rpm, I wouldn't have spun it so fast (well, I might have anyway)

Rusty · 10-20-2020, 08:17 PM

Quote:

Originally Posted by Rusty

Never seen one that's tack welded to the shaft.

You sure it didn't weld it's self to the shaft?

Quote:

Originally Posted by redondoaveb

Straight from the email I received from vortech. I then talked to another shop that verified it.

"The gear sets are matched sets, the oil slinger is welded to the shaft, so it can’t just be replaced by itself"

Ok, I see that it uses a disc instead of a ring. From the pictures I've seen. It looks like the disc distorts at high rpm. Then it makes contact, destroying it's self.

10-20-2020, 02:30 PM	#2 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	Oh my! Is this yours? Sent from my SM-G965U using Tapatalk Rusty, Spooler and redondoaveb like this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

10-20-2020, 03:04 PM	#5 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Yes but define "overspun". I know you are going into warp mode with yours. Lets not confuse guys in thinking taking it up a few K past limit is going to result in catastrophic melt down. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

10-20-2020, 03:41 PM	#7 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,184 Drives: 2011 Nismo GM 6M Rep Power: 2684437	What's the slinger made of? Brass or steel? What I found with the brass slingers on other equipment. Is that if they get a worn spot on the inside. When the equipment stops and the slinger comes to rest. If it rests on that worn spot. When the equipment is restarted. The slinger will NOT spin with the shaft. The other thing is if the slinger is out of round. The same thing happens. With either brass or steel. JARblue and redondoaveb like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

10-20-2020, 06:24 PM	#11 (permalink)
Leingod A True Z Fanatic Join Date: Mar 2015 Location: Some Place Cold Posts: 16,060 Drives: In Circles Rep Power: 2684396	Meh. Jar will still buy it if you post it in the for sale section. JARblue, Rusty, redondoaveb and 1 others like this. __________________ I AM FLOOF! SOMEBODY FLOOF MY HORN!! ALL HAIL THE FLOOF!!I JUST FLOOFED ON THE FLOOR

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Possible HD CSC Failure or Transmission Failure	kbc749	Engine & Drivetrain	9	10-04-2020 10:34 AM
[FOR SALE] vortech 2.87 pulley	st33zygill	Parts for sale (Private Classifieds)	3	08-20-2018 06:46 AM
Vortech V3 Oil Slinger	MoulaZ	Forced Induction	4	03-17-2017 10:32 PM
different noise from vortech help	Nissan370	Forced Induction	19	01-26-2013 07:23 PM
Vortech is looking.	Solus	Forced Induction	16	08-27-2009 04:04 PM

10-20-2020, 03:03 PM	#4 (permalink)
Jap**Vet* Enthusiast Member Join Date: Nov 2017 Location: Illinois Posts: 479 Drives: 2009 370z Rep Power: 115134	😳😳😳😳