Wueros tt build

Wuero370z · 12-29-2020, 11:05 PM

Quote:

Originally Posted by Elmo370z

Justin was launching at 7,000 Rpms on a stock axles. Did you load the rear end before dumping the clutch?

I did not. I believe I will start preloading it but need to get a better brake setup or a handbrake

Sent from my iPhone using Tapatalk

jchammond · 12-30-2020, 03:45 AM

They look like this

jchammond · 12-30-2020, 04:14 AM

Quote:

Originally Posted by JARblue

You can put the money towards the upgraded ones. That way they don't break the one time you do visit a drag strip

I'll even pay you ahead of time so you can order the new ones and still be running while they build them. You know I don't install anything I purchase

Sounds like a good deal

Here’s the build sheet, if you phone them with questions

Elmo370z · 12-30-2020, 08:55 AM

Quote:

Originally Posted by Wuero370z

I did not. I believe I will start preloading it but need to get a better brake setup or a handbrake

Sent from my iPhone using Tapatalk

That’s why your axles snapped. Oem
Axles can handle a lot of power, but you have to be careful launching the car especially on a prepped surface.

Spooler · 12-30-2020, 09:21 AM

Quote:

Originally Posted by Elmo370z

That’s why your axles snapped. Oem
Axles can handle a lot of power, but you have to be careful launching the car especially on a prepped surface.

That's the point. Slipping the clutch like that kills it. So folks put in axles. The better the prep, the worse it gets. To get a more consistent launch folks use clutch delay valves. The fast manual tranny guys use a slipper clutch.

Wuero370z · 01-21-2021, 04:05 PM

Anyone running slicks that chooses to match height with a skinny up front, I HIGHLY recommend sticking to 27.5 vs a 28.
I had a lot of rub with stock suspension and now with coil overs set pretty tall, and stiff, they rub on any dips or sharp bumps over 10mph. But darn that 28 looks good
I definitely snapped another axle roll racing which I believe was due to not torqing the axle nut properly. I was about to buy the 1400hp ones from soho but I couldn’t miss that intake manifold deal. Those are next on the list for sure.

Here’s a video of me roll racing a bunch of people on my buddys drag racing channel(hence his hate for rolls) Sorry the quality is pretty rough, I’m just glad to be out driving. The car scoots and boots for sure. I am dead even with a 894whp twin turbo gt350(loaded) and the CtsV from the video is 954 whp.... The Tt coyote destroyed me unfortunately but a visit to Mazworx in due time will solve that.
Ignite red is the bees knees, mixed 10 gallons with about 5 of pump e85(e72 was that ecutek was reading before) which brought me right to e84. Need to get a draggy.

https://youtu.be/oSpQK_D6nx0

Sent from my iPhone using Tapatalk

Wuero370z · 02-10-2021, 04:23 PM

Thanks to Blue ranger for finding a set of used DSS 1200hp axles on Facebook for me

Got them for 1500 shipped which is less than half what I was going to pay for the 1400hp ones!

Question, do y’all think I need to preload these?
I know the specialty Z clutch was not meant to be slipped so I’m kinda wondering if clutch drop is going to be ok?

Sent from my iPhone using Tapatalk

Spooler · 02-10-2021, 04:43 PM

I don't know. The only ones to break the 1200hp axles was SOHO.

Elmo370z · 02-10-2021, 09:11 PM

Quote:

Originally Posted by Wuero370z

Thanks to Blue ranger for finding a set of used DSS 1200hp axles on Facebook for me

Got them for 1500 shipped which is less than half what I was going to pay for the 1400hp ones!

Question, do y’all think I need to preload these?
I know the specialty Z clutch was not meant to be slipped so I’m kinda wondering if clutch drop is going to be ok?

Sent from my iPhone using Tapatalk

Sell the clutch, get a proper clutch set up and a clutch slipper.

jchammond · 02-11-2021, 05:13 AM

Good explanation about intake purchase

As mine initially won’t exceed 20#

Gotta make enough sauce to pay that one Ford back

But you may end up back at square 1 with traction

Wuero370z · 03-18-2021, 09:42 AM

Out here at Texas 2k. Let me know if anyone is trying to race!

Sent from my iPhone using Tapatalk

Elmo370z · 03-18-2021, 10:38 AM

Quote:

Originally Posted by Wuero370z

Out here at Texas 2k. Let me know if anyone is trying to race!

Sent from my iPhone using Tapatalk

Drag or roll racing. Turn the flame map on high

Wuero370z · 03-18-2021, 11:41 AM

Hoping to do a bit of both

DSS axles are on and I’ve got the spicy tune ready to go! It definitely shoots flames on shift under high load so we see

Sent from my iPhone using Tapatalk

Wuero370z · 03-23-2021, 11:34 AM

Couldn’t find squat for races in Texas. Cops were insane. Went to a dig spot and ended up snapping something. Not sure if it’s the diff, axle, or driveshaft but I’m gunna find out today.
Thought once I did the axles everything would be good to go but ya I dumped that clutch and something snapped

Sent from my iPhone using Tapatalk

Spooler · 03-23-2021, 12:54 PM

Ugg, do you feel any vibration when you select a gear. It may be your input shaft.

01-21-2021, 04:05 PM	#66 (permalink)
Wuero370z Enthusiast Member Join Date: Nov 2018 Location: Albuquerque Posts: 358 Drives: 2013 Nissan 370z Rep Power: 6717	Anyone running slicks that chooses to match height with a skinny up front, I HIGHLY recommend sticking to 27.5 vs a 28. I had a lot of rub with stock suspension and now with coil overs set pretty tall, and stiff, they rub on any dips or sharp bumps over 10mph. But darn that 28 looks good I definitely snapped another axle roll racing which I believe was due to not torqing the axle nut properly. I was about to buy the 1400hp ones from soho but I couldn’t miss that intake manifold deal. Those are next on the list for sure. Here’s a video of me roll racing a bunch of people on my buddys drag racing channel(hence his hate for rolls) Sorry the quality is pretty rough, I’m just glad to be out driving. The car scoots and boots for sure. I am dead even with a 894whp twin turbo gt350(loaded) and the CtsV from the video is 954 whp.... The Tt coyote destroyed me unfortunately but a visit to Mazworx in due time will solve that. Ignite red is the bees knees, mixed 10 gallons with about 5 of pump e85(e72 was that ecutek was reading before) which brought me right to e84. Need to get a draggy. https://youtu.be/oSpQK_D6nx0 Sent from my iPhone using Tapatalk gbrettin, Rusty, Hotrodz and 3 others like this.

02-10-2021, 04:43 PM	#68 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	I don't know. The only ones to break the 1200hp axles was SOHO. jchammond and Wuero370z like this.

02-11-2021, 05:13 AM	#70 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	Good explanation about intake purchase As mine initially won’t exceed 20# Gotta make enough sauce to pay that one Ford back But you may end up back at square 1 with traction Wuero370z likes this. __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

03-18-2021, 09:42 AM	#71 (permalink)
Wuero370z Enthusiast Member Join Date: Nov 2018 Location: Albuquerque Posts: 358 Drives: 2013 Nissan 370z Rep Power: 6717	Out here at Texas 2k. Let me know if anyone is trying to race! Sent from my iPhone using Tapatalk Hotrodz, Spooler and redondoaveb like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The Mag Z Build	TheMagZ	Member's 370Z Gallery	16	07-09-2016 08:46 PM
My Build	skoolio	Member's 370Z Gallery	6	02-08-2016 09:55 PM
TT build in Fl	travnflorida	Nissan 370Z General Discussions	3	08-15-2011 06:51 PM
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD	Reaper42	Forced Induction	14	01-22-2011 06:24 PM
Datsun Roadster 1600...To build or not to build	motoextreme	The Lounge (Off Topic)	66	02-13-2010 01:40 AM

02-10-2021, 04:23 PM	#67 (permalink)
Wuero370z Enthusiast Member Join Date: Nov 2018 Location: Albuquerque Posts: 358 Drives: 2013 Nissan 370z Rep Power: 6717	Thanks to Blue ranger for finding a set of used DSS 1200hp axles on Facebook for me Got them for 1500 shipped which is less than half what I was going to pay for the 1400hp ones! Question, do y’all think I need to preload these? I know the specialty Z clutch was not meant to be slipped so I’m kinda wondering if clutch drop is going to be ok? Sent from my iPhone using Tapatalk

03-18-2021, 11:41 AM	#73 (permalink)
Wuero370z Enthusiast Member Join Date: Nov 2018 Location: Albuquerque Posts: 358 Drives: 2013 Nissan 370z Rep Power: 6717	Hoping to do a bit of both DSS axles are on and I’ve got the spicy tune ready to go! It definitely shoots flames on shift under high load so we see Sent from my iPhone using Tapatalk

03-23-2021, 11:34 AM	#74 (permalink)
Wuero370z Enthusiast Member Join Date: Nov 2018 Location: Albuquerque Posts: 358 Drives: 2013 Nissan 370z Rep Power: 6717	Couldn’t find squat for races in Texas. Cops were insane. Went to a dig spot and ended up snapping something. Not sure if it’s the diff, axle, or driveshaft but I’m gunna find out today. Thought once I did the axles everything would be good to go but ya I dumped that clutch and something snapped Sent from my iPhone using Tapatalk

03-23-2021, 12:54 PM	#75 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	Ugg, do you feel any vibration when you select a gear. It may be your input shaft.