DIY twin turbo Z

Quicksilvers · 09-23-2019, 07:51 AM

The best of luck with your build it will be trail and error doing a custom build yourself to get the fitment proper take your time and give him some credit for the attempt to do his own build. Those turbos create a lot of heat as well definitely try not to mount the turbos where they will not rub against the subframe and/or any body parts. Any damage to the manifolds and it will be inevitable you will have to disassemble everything.

ozyo · 09-23-2019, 02:08 PM

To be honest, I don’t have a lot to post about
I'm still stuck at the driver-side manifold
just received wastegates and some other parts that have nothing to do with the turbos

ozyo · 09-23-2019, 02:27 PM

Quote:

Originally Posted by Martijn_b

Like your creativity! Keep posting

Sent from my SM-G973F using Tapatalk

Thanx

Quote:

Originally Posted by Trips

(Not Hating) But the quality of workmanship is pretty close to ghetto imo

700+ hp.

Good Luck!

Which to be expected I mean you need to start somewhere

Quote:

Originally Posted by Jayhovah

subbed

Welcome

Quote:

Originally Posted by Rusty

When he gets done with this project. He might have a degree in backyard engineering. I'm going to be grading him on-line.

Quote:

Originally Posted by Rusty

If it requires 3 or more rolls of duct tape. It's above,

challenge accepted

Quote:

Originally Posted by jwick

Is that above or below redneck engineering?

Quote:

Originally Posted by Spooler

That depends on the Redneck. LMAO....

Anything will do

Quote:

Originally Posted by BoneZ

Me too. I'll bite. I started body work this way. I messed up a lot, but I learned a lot.

You going to wait for long time

im very slow

Quote:

Originally Posted by TopgunZ

All I can think of is to be careful how close those turbos are mounted to the body of the car. Dont forget that the engine shifts around. Those snails might slam into the body and put stress on the manifolds, causing a crack/leak.

Good luck! Definitely some outside the box thinking here, which I like.

how much space should I leave ?

Quote:

Originally Posted by Quicksilvers

The best of luck with your build it will be trail and error doing a custom build yourself to get the fitment proper take your time and give him some credit for the attempt to do his own build. Those turbos create a lot of heat as well definitely try not to mount the turbos where they will not rub against the subframe and/or any body parts. Any damage to the manifolds and it will be inevitable you will have to disassemble everything.

believe me I know I change the manifold design more than five time

for the heat I'm not sure should I ceramic coated or go
with turbo blanket

09-23-2019, 07:51 AM	#1 (permalink)
Quicksilvers A True Z Fanatic Join Date: May 2017 Location: Atlanta, GA Posts: 2,039 Drives: 2017 370z Rep Power: 25463	The best of luck with your build it will be trail and error doing a custom build yourself to get the fitment proper take your time and give him some credit for the attempt to do his own build. Those turbos create a lot of heat as well definitely try not to mount the turbos where they will not rub against the subframe and/or any body parts. Any damage to the manifolds and it will be inevitable you will have to disassemble everything. ozyo, ZontheRocks and Martijn_b like this. __________________ Mr. Clean

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Twin Turbo build in progress: Another Gamma V3 Twin turbo install	Nyght	Forced Induction	37	08-08-2017 09:27 AM
Which stage of twin-turbo/twin-supercharger kit should I get?	Nuc370z	Forced Induction	13	12-30-2015 07:15 PM
Twin Turbo vs. Single Turbo V6: A Dissertation	Mike@GTM	Forced Induction	115	08-14-2014 09:04 PM
GTM MHI Twin Turbo vs. Fast Intentions Twin Turbo	isayimandrew	Forced Induction	26	05-29-2013 08:47 PM
GTM Motorsports Twin Turbo vs Greddy Twin Turbo Kit	Nismo221	Forced Induction	57	08-16-2011 04:44 PM

09-23-2019, 02:08 PM	#2 (permalink)
ozyo Base Member Join Date: Oct 2016 Location: oman Posts: 12 Drives: 14 370Z mt Rep Power: 6719	To be honest, I don’t have a lot to post about I'm still stuck at the driver-side manifold just received wastegates and some other parts that have nothing to do with the turbos