No Self Installers?

wolfcyn · 10-27-2018, 12:59 PM

I may end up catching a lot of heat for this...but oh well. I’ve been doing a good bit of research on the AAM twin turbo kit for a while now(maybe not enough). But I’ve always wondered why there are no detailed install videos on boosting these cars. I’ve read over the instructions for the procedure, and to me it does not really seem all that difficult, just a lot of parts and steps. I am no expert when it comes to boosting a vehicle so I am sure there are a ton of unwritten things that goes along with such a project. But I’m just curious on what to look forward to when I attempt to install my own kit. Lack of equipment? Time?

Sent from my iPhone using Tapatalk

*J*ap***V*et* · 10-27-2018, 01:16 PM

I have never done it myself but I knew a guy Kyle that boosted his 420a Talon. He and his dad ran a small shop and it took them about 12 hours. That was a single turbo and components from a gst eclipse. It ended up pushing a rod into the valves. It certainly isn't a task for the faint of heart and both were somewhat mechanically inclined lol

Spooler · 10-27-2018, 01:50 PM

It has been done before with a Fast Intentions kit. Their kit has very good instructions. The AAM nobody wants that are in the know because of all of the pitfalls it has. Plus they have poor customer service. The intercooler (CAC) is too small, the turbo's have internal gates which will cause boost creap, etc. It has been said before and I will say it again. You need at least 25k to start a TT upgrade. If you don't have the cash for that laying around you don't need to do the upgrade. The TT kit itself is the cheapest part of the build.

CRiZO · 10-27-2018, 01:53 PM

Just labor intensive. Boosting a car is boosting a car. Most of my cars have been turbo'd, people seem to think it's complicated but it's not if you're mechanically inclined and have any sort of project management skills. The Z will be a frustratingly tight space to work in though. I couldn't imagine doing it without a lift. Personally I'd avoid AAM, their business seems to be a mess.

No surprise about the 420a lol. The DSM guys are the cheapest people on the planet and spend just as much as everyone else because they're always breaking **** lol.

*J*ap***V*et* · 10-27-2018, 02:00 PM

Quote:

Originally Posted by CRiZO

Just labor intensive. Boosting a car is boosting a car. Most of my cars have been turbo'd, people seem to think it's complicated but it's not. The Z will be a frustratingly tight space to work in though. I couldn't imagine doing it without a lift. Personally I'd avoid AAM, their business seems to be a mess.

No surprise about the 420a lol. The DSM guys are the cheapest people on the planet and spend just as much as everyone else because they're always breaking **** lol.

Bro....true story lol...car ran it's a** off for a few weeks. The build was simple but the execution was wayyy off! Funny thing is we had a buddy that boosted his integra and that thing lasted for years.

wolfcyn · 10-27-2018, 02:43 PM

Quote:

Originally Posted by Spooler

It has been done before with a Fast Intentions kit. Their kit has very good instructions. The AAM nobody wants that are in the know because of all of the pitfalls it has. Plus they have poor customer service. The intercooler (CAC) is too small, the turbo's have internal gates which will cause boost creap, etc. It has been said before and I will say it again. You need at least 25k to start a TT upgrade. If you don't have the cash for that laying around you don't need to do the upgrade. The TT kit itself is the cheapest part of the build.

This is interesting. I heard that AAM's customer service has not been the best in the past. Guess it is time for me to do some more research. I do not plan on going through with this for the next few years. Just trying to learn as much about it as I can before I dive into it.

Jinxx · 10-27-2018, 04:09 PM

I installed a GTM supercharger stage 2 kit on my 2015 nismo and a boosted performance kit on my 2017 nismo .. both were done over a weekend and was pretty easy to do .. not sure if you was referring to the AAM KIT or any self installed kit ... from my understanding the twin turbo kits require removing the motor for install.

jwick · 10-27-2018, 06:16 PM

I installed my BP kit in my buddy’s garage.

Boosted Performance · 10-27-2018, 09:26 PM

I have always said to customer that are looking at installing a Boosted Performance turbo kit...if you can remove your OEM catalytic converters, you can install the turbo kit. It is probably the biggest P.I.T.A to do really...well, some may find the fuel pump a bit overwhelming, but that has to be done with every single forced induction kit out there.

Now with the Oil-less turbos, it is also much easier, no need to mess with anything oil related. Just splice two T fitting in to the heater core hoses, and that's it as far as liquids for the turbo go. The rest of the kit assembles like Lego.

Should also mention that most of these kits I have sold (close to 100 for the VHR alone) have been installed by the customers themselves.

jchammond · 10-27-2018, 10:09 PM

Great Customer Service!

wolfcyn · 10-27-2018, 11:08 PM

Quote:

Originally Posted by Boosted Performance

I have always said to customer that are looking at installing a Boosted Performance turbo kit...if you can remove your OEM catalytic converters, you can install the turbo kit. It is probably the biggest P.I.T.A to do really...well, some may find the fuel pump a bit overwhelming, but that has to be done with every single forced induction kit out there.

Now with the Oil-less turbos, it is also much easier, no need to mess with anything oil related. Just splice two T fitting in to the heater core hoses, and that's it as far as liquids for the turbo go. The rest of the kit assembles like Lego.

Should also mention that most of these kits I have sold (close to 100 for the VHR alone) have been installed by the customers themselves.

This has really been my mindset when it comes to installing the kit so far. Ive already put a walbro 255 fuel pump in and it was skeptical at first, but if someone else could do it, I did not see why i would not be able to.

Boosted Performance · 10-28-2018, 02:02 AM

Quote:

Originally Posted by wolfcyn

This has really been my mindset when it comes to installing the kit so far. Ive already put a walbro 255 fuel pump in and it was skeptical at first, but if someone else could do it, I did not see why i would not be able to.

ABSOLUTELY....that is a life attitude for me.

Spooler · 10-28-2018, 12:54 PM

Quote:

Originally Posted by wolfcyn

but if someone else could do it, I did not see why i would not be able to.

The problem on the forums is you have no idea what kind of skills the guy on the other end of the keyboard has. He may have 20yrs experience or he may have no experience. It is extremely difficult to give any solid advice. I have worked with folks that should not be allowed to touch a car and some that were extremely good.

James10694 · 11-13-2018, 02:22 AM

I installed my boosted performance kit on my 2010 370z. The only work I did before that was oil changes and an exhaust install. I did skip the fuel pump though, I'm horrible with electrical work.

jchammond · 11-13-2018, 03:44 AM

I’m gonna finish helping a friend complete his in a couple weeks; a lot of preliminary things were performed before even touching any shiny parts,,,getting lift operational,removal of old exhaust,diff & transmission....replace rear diff bushings,clutch,flywheel,pressure plate,cmak & clean up all bolts & holes with re-threader (for ease of installation),,,also remove inverted torx bolts in manifolds & punch out holes to size of others...the larger fasteners keep gaskets alignment better & less worry of breaking from vibrations etc...also upon installation of diff,cv axles,flywheel,clutch & tranny...used loctite where required & torque wrench for proper tightness. I’m gonna take my time performing tasks as these...being the 1st time working with a BP kit- Want to ensure everything is perfect. Not much left to do,,,a nice CJM fuel system & some plumbing...hopefully the weather will be decent enough to draw some lines on some nearby asphalt

10-27-2018, 12:59 PM	#1 (permalink)
wolfcyn Base Member Join Date: Dec 2015 Location: Mississippi Posts: 67 Drives: 2016 Nissan 370z 7AT Rep Power: 10	No Self Installers? I may end up catching a lot of heat for this...but oh well. I’ve been doing a good bit of research on the AAM twin turbo kit for a while now(maybe not enough). But I’ve always wondered why there are no detailed install videos on boosting these cars. I’ve read over the instructions for the procedure, and to me it does not really seem all that difficult, just a lot of parts and steps. I am no expert when it comes to boosting a vehicle so I am sure there are a ton of unwritten things that goes along with such a project. But I’m just curious on what to look forward to when I attempt to install my own kit. Lack of equipment? Time? Sent from my iPhone using Tapatalk

10-27-2018, 01:50 PM	#3 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	It has been done before with a Fast Intentions kit. Their kit has very good instructions. The AAM nobody wants that are in the know because of all of the pitfalls it has. Plus they have poor customer service. The intercooler (CAC) is too small, the turbo's have internal gates which will cause boost creap, etc. It has been said before and I will say it again. You need at least 25k to start a TT upgrade. If you don't have the cash for that laying around you don't need to do the upgrade. The TT kit itself is the cheapest part of the build. jwick, Chuck33079, Jap**Vet* and 1 others like this.

10-27-2018, 01:53 PM	#4 (permalink)
CRiZO Track Member Join Date: Nov 2017 Location: Dallas Posts: 672 Drives: in traffic Rep Power: 20699	Just labor intensive. Boosting a car is boosting a car. Most of my cars have been turbo'd, people seem to think it's complicated but it's not if you're mechanically inclined and have any sort of project management skills. The Z will be a frustratingly tight space to work in though. I couldn't imagine doing it without a lift. Personally I'd avoid AAM, their business seems to be a mess. No surprise about the 420a lol. The DSM guys are the cheapest people on the planet and spend just as much as everyone else because they're always breaking **** lol. Jap**Vet* likes this. Last edited by CRiZO; 10-27-2018 at 01:57 PM.

10-27-2018, 06:16 PM	#8 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465057	I installed my BP kit in my buddy’s garage. wideglideleon likes this. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

10-27-2018, 09:26 PM	#9 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3382	I have always said to customer that are looking at installing a Boosted Performance turbo kit...if you can remove your OEM catalytic converters, you can install the turbo kit. It is probably the biggest P.I.T.A to do really...well, some may find the fuel pump a bit overwhelming, but that has to be done with every single forced induction kit out there. Now with the Oil-less turbos, it is also much easier, no need to mess with anything oil related. Just splice two T fitting in to the heater core hoses, and that's it as far as liquids for the turbo go. The rest of the kit assembles like Lego. Should also mention that most of these kits I have sold (close to 100 for the VHR alone) have been installed by the customers themselves. JARblue, James10694, jchammond and 2 others like this. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg Last edited by Boosted Performance; 10-27-2018 at 09:43 PM.

10-27-2018, 01:16 PM	#2 (permalink)
Jap**Vet* Enthusiast Member Join Date: Nov 2017 Location: Illinois Posts: 479 Drives: 2009 370z Rep Power: 115134	I have never done it myself but I knew a guy Kyle that boosted his 420a Talon. He and his dad ran a small shop and it took them about 12 hours. That was a single turbo and components from a gst eclipse. It ended up pushing a rod into the valves. It certainly isn't a task for the faint of heart and both were somewhat mechanically inclined lol

10-27-2018, 04:09 PM	#7 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3376	I installed a GTM supercharger stage 2 kit on my 2015 nismo and a boosted performance kit on my 2017 nismo .. both were done over a weekend and was pretty easy to do .. not sure if you was referring to the AAM KIT or any self installed kit ... from my understanding the twin turbo kits require removing the motor for install.

10-27-2018, 10:09 PM	#10 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	Great Customer Service! __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

11-13-2018, 02:22 AM	#14 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 917 Drives: 2010 370z Nismo Rep Power: 13	I installed my boosted performance kit on my 2010 370z. The only work I did before that was oil changes and an exhaust install. I did skip the fuel pump though, I'm horrible with electrical work. madwi likes this. __________________ Boosted Performance Single Turbo 618whp/489 tq

11-13-2018, 03:44 AM	#15 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	I’m gonna finish helping a friend complete his in a couple weeks; a lot of preliminary things were performed before even touching any shiny parts,,,getting lift operational,removal of old exhaust,diff & transmission....replace rear diff bushings,clutch,flywheel,pressure plate,cmak & clean up all bolts & holes with re-threader (for ease of installation),,,also remove inverted torx bolts in manifolds & punch out holes to size of others...the larger fasteners keep gaskets alignment better & less worry of breaking from vibrations etc...also upon installation of diff,cv axles,flywheel,clutch & tranny...used loctite where required & torque wrench for proper tightness. I’m gonna take my time performing tasks as these...being the 1st time working with a BP kit- Want to ensure everything is perfect. Not much left to do,,,a nice CJM fuel system & some plumbing...hopefully the weather will be decent enough to draw some lines on some nearby asphalt Rusty, madwi and JLarson like this. __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Installers/Shops	km1346	Texas	7	10-26-2014 12:33 AM
Clear Bra Installers	Quantum	Canada	0	04-01-2014 06:56 AM
Car security installers	Tribalpinoy91	Mid-Atlantic Region	0	10-02-2013 03:59 PM
MN 3M di-noc installers?	JunoonX	Mid Western Region	0	08-10-2011 11:02 PM
installers need advice please	boomboom	Audio & Video	26	11-12-2010 11:02 PM