Fast Intentions Stage 2 TT build by MA-Motorsports.

Elmo370z · 06-07-2021, 06:24 PM

Quote:

Originally Posted by BettyZ

723. Moncef really struggles with tunes over 700.

Why would you have monqueef tune your car?

redondoaveb · 06-07-2021, 06:39 PM

Quote:

Originally Posted by Elmo370z

Why would you have monqueef tune your car?

For the pops and bangs. He's getting married. The only popping and banging he'll be doing is in his car

Elmo370z · 06-07-2021, 07:27 PM

Quote:

Originally Posted by redondoaveb

For the pops and bangs. He's getting married. The only popping and banging he'll be doing is in his car

He good at doing that.

Spooler · 06-07-2021, 08:07 PM

Quote:

Originally Posted by redondoaveb

For the pops and bangs. He's getting married. The only popping and banging he'll be doing is in his car

Yup, the representative is getting ready to leave. The real wife will show up not longer after.

Trips · 06-08-2021, 02:09 AM

I'm going to ask those engaging in some personal and off topic comments to STOP!

There's no reason for it in a fellow members build thread. (Albeit I'm a little late to the party)

I'm going to ask to take the off topic comments to the non-tech section of the forum.

I would also appreciate it if we can drop the borderline personal/harassment comments.

Thanks Trips

JARblue · 06-08-2021, 08:48 AM

Quote:

Originally Posted by Trips

Thanks Trips

You're welcome

Spooler · 06-08-2021, 10:31 AM

I ordered the Tial 1.06 AR exhaust housings yesterday from F.I. If the turbo's fall short I will have them put on. If not, I will hold until a later date. To put them on I would have to drop the motor. You can see on my previous dyno graphs that my HP/TQ falls off on the top end. If I do this it will take some spool up and midrange away and move it to the top end. I am detuning some of that anyway so I don't think it will hurt too bad. Not sure. Will wait and see.

Spooler · 06-08-2021, 10:34 AM

Quote:

Originally Posted by madwi

Red= 12psi 93octane
Blue= 17psi Ignite Red
Green= 25psi Ignite Red

Bringing this back from the dead again. I am going to take a little TQ away from the midrange to help with traction.

JARblue · 06-08-2021, 10:37 AM

Quote:

Originally Posted by Spooler

I am going to take a little TQ away from the midrange to help with traction.

Cooltoy is a photoshop wiz if you need help with the graph

Spooler · 06-08-2021, 10:43 AM

Quote:

Originally Posted by JARblue

Cooltoy is a photoshop wiz if you need help with the graph

We'll see what can be done on the dyno. It should be this week sometime. The 5130 rpm TQ spike at 25psi of boost is what I want to decrease. It needs to be a slower ramp even at 17psi. When the boost is turned up even more
it will get out of control quick. A spin fest isn't any fun.

Spooler · 06-08-2021, 10:59 AM

Dang graphs look better than what I remembered. LOL

Spooler · 06-08-2021, 11:09 AM

The changes.

New HKS sparkplugs
New SOHO cast intake manifold
New SOHO catch can setup
New Z1 coil packs
New 4 port MAC valve

Not many. We'll see what Nick can do.

Spooler · 06-08-2021, 11:12 AM

The biggest upgrade for me is Boost by gear. I couldn't use 25psi of boost except in the high gears before. Being on a boost controller sucked. ECUTEK boost by gear this time.

Spooler · 06-08-2021, 11:17 AM

Oh yeah, I messed up. I had MA connect my coolant lines to the throttle bodies on the first engine. I forgot all about it. They have now been removed. IAT's will come down some.

SeeThruHead · 06-08-2021, 11:28 AM

i'm curious to see if a the 4 port mac valve will provide you with enough resolution/accuracy or if you'll switch to something with more control

06-08-2021, 02:09 AM	#3815 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,732 Drives: 🔰 Rep Power: 10	I'm going to ask those engaging in some personal and off topic comments to STOP! There's no reason for it in a fellow members build thread. (Albeit I'm a little late to the party) I'm going to ask to take the off topic comments to the non-tech section of the forum. I would also appreciate it if we can drop the borderline personal/harassment comments. Thanks Trips FL 4Motion, Rusty, Hotrodz and 1 others like this. __________________

06-08-2021, 10:31 AM	#3817 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	I ordered the Tial 1.06 AR exhaust housings yesterday from F.I. If the turbo's fall short I will have them put on. If not, I will hold until a later date. To put them on I would have to drop the motor. You can see on my previous dyno graphs that my HP/TQ falls off on the top end. If I do this it will take some spool up and midrange away and move it to the top end. I am detuning some of that anyway so I don't think it will hurt too bad. Not sure. Will wait and see. Mr.Squeeze, Rusty, Hotrodz and 1 others like this. Last edited by Spooler; 06-08-2021 at 10:46 AM.

06-08-2021, 10:59 AM	#3821 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	Dang graphs look better than what I remembered. LOL Mr.Squeeze and JARblue like this.

06-08-2021, 11:09 AM	#3822 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	The changes. New HKS sparkplugs New SOHO cast intake manifold New SOHO catch can setup New Z1 coil packs New 4 port MAC valve Not many. We'll see what Nick can do. FL 4Motion, JARblue, Hotrodz and 1 others like this. Last edited by Spooler; 06-08-2021 at 11:22 AM.

06-08-2021, 11:12 AM	#3823 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	The biggest upgrade for me is Boost by gear. I couldn't use 25psi of boost except in the high gears before. Being on a boost controller sucked. ECUTEK boost by gear this time. FL 4Motion, JARblue, Rusty and 2 others like this. Last edited by Spooler; 06-08-2021 at 11:24 AM.

06-08-2021, 11:17 AM	#3824 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	Oh yeah, I messed up. I had MA connect my coolant lines to the throttle bodies on the first engine. I forgot all about it. They have now been removed. IAT's will come down some. JARblue, Rusty and Hotrodz like this.

06-08-2021, 11:28 AM	#3825 (permalink)
SeeThruHead Track Member Join Date: Jun 2020 Location: Toronto Posts: 716 Drives: Red '18 Sport Manual Rep Power: 23498	i'm curious to see if a the 4 port mac valve will provide you with enough resolution/accuracy or if you'll switch to something with more control __________________ My Build thread STH Build Plan Thread Images too big fix here

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Fast Intentions Stage 2 Twin Turbo Kit	Nik@SOHO	Parts for sale (Private Classifieds)	60	10-09-2017 09:11 AM
370Z For Sale 2015 Nismo Tech with Fast Intentions Stage 2 637HP	DPE G	370Z For Sale	2	06-03-2017 12:40 PM
MA Motorsports: FAST Intentions \| HKS \| APEXi \| TANABE	MAMotorsports	Exhaust/Intake	46	05-23-2016 12:12 PM
My 09 NISMO Fast Intentions TT Build	katjmmx	Forced Induction	142	05-19-2016 03:32 PM
[FOR SALE] Fast Intentions Exhaust Build #952 Placement	NismoZ70	Parts for sale (Private Classifieds)	11	03-19-2014 10:27 AM