Fast Intentions Stage 2 TT build by MA-Motorsports.

Spooler · 01-10-2021, 03:13 AM

Quote:

Originally Posted by GeauxTigers1

“Falls through??” Why you say negative words like that! Lol

What’s the CJM one? I can’t find anything on it but a forum thread from a few years ago mentioning it but not real details, price, numbers etc.

I hope we get a price next week. It is the easiest route. Otherwise the choice get's slimmed way way down.

GeauxTigers1 · 01-10-2021, 03:15 AM

Quote:

Originally Posted by jchammond

That’s a one-off that Charles built, but requires some fabbing to install & probably a different intercooler.
Spooler is on top of his game with all of this, very valuable information in this whole thread!

Ha yep! I think I just found it. Looks so freaking sweet but a reroute of just about everything in our engine bay. 😫

https://conceptzperformance.com/cj-m...de_p_28400.php

jchammond · 01-10-2021, 03:15 AM

Quote:

Originally Posted by Spooler

I doubt it. We are all lined up because turbo cars have a limit. Once the headgasket issue is fixed the next problem is the plastic intake. I will retune to 30psi and boost by gear. I want to hear those turbo's sing...

30# would really make them sing

Just think; engine is rated for up to 40#

jchammond · 01-10-2021, 03:17 AM

Quote:

Originally Posted by GeauxTigers1

Ha yep! I think I just found it. Looks so freaking sweet but a reroute of just about everything in our engine bay. 😫

https://conceptzperformance.com/cj-m...de_p_28400.php

That looks similar; seems like the one I remember had twin TB’s up front

I could be mistaken though

Spooler · 01-10-2021, 03:18 AM

Quote:

Originally Posted by jchammond

30# would really make them sing

Just think; engine is rated for up to 40#

That would be out of my turbo's efficiency range I beat. What I would call blowing hot air. The next weak link would be the crank if the block is good to go. Nobody really knows since we are getting into new territory.

Spooler · 01-10-2021, 03:19 AM

That one.

CJM Billet Intake Manifold

Spooler · 01-10-2021, 03:22 AM

Quote:

Originally Posted by GeauxTigers1

Ha yep! I think I just found it. Looks so freaking sweet but a reroute of just about everything in our engine bay. 😫

https://conceptzperformance.com/cj-m...de_p_28400.php

I am not sure on the price. The problem is it takes a while for Phunk to make it IF he even has time. You would pay and forget about it for a while until it hits your doorstep type deal.

jchammond · 01-10-2021, 03:23 AM

Found a pic

SeeThruHead · 01-10-2021, 03:31 AM

Well I just read from page 25 to page 87 in one sitting. Wow what a roller coaster. Car is a monster. Amazing how transparent this build has been. I haven't watched all the videos yet but so much LEARNING. wow

Spooler · 01-10-2021, 03:34 AM

Quote:

Originally Posted by SeeThruHead

Well I just read from page 25 to page 87 in one sitting. Wow what a roller coaster. Car is a monster. Amazing how transparent this build has been. I haven't watched all the videos yet but so much LEARNING. wow

Mr. Squeeze took 2 weeks to read it 60 or so pages back. LOL It has been a rollercoaster ride that is for sure.

SeeThruHead · 01-10-2021, 03:47 AM

Yeah I have it set to 40 posts per page so there’s only 87 pages total. The first 25 tool we a week but then when you got the car back the first time. And it blew up, I couldn’t stop reading. Good stuff.

EDIT:

So Spooler. I watching some of the videos and thinking about my own build, i'm trying to learn from what you've done here. I'm wondering about displacement now. Would increasing displacement allow me to reach higher HP with lower boost and lower compression (and worse fuel, we don't have ethanol at the pump here, i'm not going to mix my own fuel). The Brian Crower stroker kit comes to mind. Boring larger on the stock block seems iffy from the information I've gathered from your thread, would allow for much easier distortion of the cylinder it seem. But larger sleeves maybe? What's the reason you didn't increase displacement in either of your engine builds?

Spooler · 01-10-2021, 04:15 PM

Quote:

Originally Posted by SeeThruHead

Yeah I have it set to 40 posts per page so there’s only 87 pages total. The first 25 tool we a week but then when you got the car back the first time. And it blew up, I couldn’t stop reading. Good stuff.

EDIT:

So Spooler. I watching some of the videos and thinking about my own build, i'm trying to learn from what you've done here. I'm wondering about displacement now. Would increasing displacement allow me to reach higher HP with lower boost and lower compression (and worse fuel, we don't have ethanol at the pump here, i'm not going to mix my own fuel). The Brian Crower stroker kit comes to mind. Boring larger on the stock block seems iffy from the information I've gathered from your thread, would allow for much easier distortion of the cylinder it seem. But larger sleeves maybe? What's the reason you didn't increase displacement in either of your engine builds?

I didn't see a need in increasing displacement. To go to a 4.0 liter I would have needed a stroker crank. I am happy with the power I have to be honest. The car is a handful now. More than most can drive. I have been driving turbo cars for years. Good luck getting in the 700hp range on pump gas. It can be done but longevity I do not know. You can go to a much larger bore with Darton MID sleeves. If you have never had a high hp car, start out at a lower hp and work your way up.

SeeThruHead · 01-10-2021, 06:38 PM

Quote:

Originally Posted by Spooler

I didn't see a need in increasing displacement. To go to a 4.0 liter I would have needed a stroker crank. I am happy with the power I have to be honest. The car is a handful now. More than most can drive. I have been driving turbo cars for years. Good luck getting in the 700hp range on pump gas. It can be done but longevity I do not know. You can go to a much larger bore with Darton MID sleeves. If you have never had a high hp car, start out at a lower hp and work your way up.

Yep that's the plan. I've layed out my stages and will be staying NA for a while before going to moderate boost. Staying on that for a while before building the engine and turning it up. I have a lot of driver training and track days in mind.

Spooler · 01-10-2021, 11:24 PM

Anybody want to upgrade their manual transmission? See other thread. PPG is interested.

Built Manual Transmission

Spooler · 01-11-2021, 05:10 PM

We are still waiting on SOHO...

01-10-2021, 03:31 AM	#3474 (permalink)
SeeThruHead Track Member Join Date: Jun 2020 Location: Toronto Posts: 716 Drives: Red '18 Sport Manual Rep Power: 23498	Well I just read from page 25 to page 87 in one sitting. Wow what a roller coaster. Car is a monster. Amazing how transparent this build has been. I haven't watched all the videos yet but so much LEARNING. wow FL 4Motion, GeauxTigers1, Rusty and 5 others like this. __________________ My Build thread STH Build Plan Thread Images too big fix here

01-10-2021, 03:47 AM	#3476 (permalink)
SeeThruHead Track Member Join Date: Jun 2020 Location: Toronto Posts: 716 Drives: Red '18 Sport Manual Rep Power: 23498	Yeah I have it set to 40 posts per page so there’s only 87 pages total. The first 25 tool we a week but then when you got the car back the first time. And it blew up, I couldn’t stop reading. Good stuff. EDIT: So Spooler. I watching some of the videos and thinking about my own build, i'm trying to learn from what you've done here. I'm wondering about displacement now. Would increasing displacement allow me to reach higher HP with lower boost and lower compression (and worse fuel, we don't have ethanol at the pump here, i'm not going to mix my own fuel). The Brian Crower stroker kit comes to mind. Boring larger on the stock block seems iffy from the information I've gathered from your thread, would allow for much easier distortion of the cylinder it seem. But larger sleeves maybe? What's the reason you didn't increase displacement in either of your engine builds? __________________ My Build thread STH Build Plan Thread Images too big fix here Last edited by SeeThruHead; 01-10-2021 at 02:15 PM.

01-10-2021, 11:24 PM	#3479 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	Anybody want to upgrade their manual transmission? See other thread. PPG is interested. Built Manual Transmission GeauxTigers1 and Hotrodz like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Fast Intentions Stage 2 Twin Turbo Kit	Nik@SOHO	Parts for sale (Private Classifieds)	60	10-09-2017 09:11 AM
370Z For Sale 2015 Nismo Tech with Fast Intentions Stage 2 637HP	DPE G	370Z For Sale	2	06-03-2017 12:40 PM
MA Motorsports: FAST Intentions \| HKS \| APEXi \| TANABE	MAMotorsports	Exhaust/Intake	46	05-23-2016 12:12 PM
My 09 NISMO Fast Intentions TT Build	katjmmx	Forced Induction	142	05-19-2016 03:32 PM
[FOR SALE] Fast Intentions Exhaust Build #952 Placement	NismoZ70	Parts for sale (Private Classifieds)	11	03-19-2014 10:27 AM

01-10-2021, 03:19 AM	#3471 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	That one. CJM Billet Intake Manifold

01-11-2021, 05:10 PM	#3480 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	We are still waiting on SOHO...