Fast Intentions Stage 2 TT build by MA-Motorsports.

Rusty · 11-23-2018, 03:04 PM

If you don't want to cut holes. Think you will end up with a new hood.

Spooler · 11-23-2018, 06:51 PM

Quote:

Originally Posted by Rusty

If you don't want to cut holes. Think you will end up with a new hood.

Na, it will be TracSpec vents like you and Bob have.

Spooler · 11-23-2018, 06:55 PM

Went by to get a 5000lb winch and they were all sold out. Just my luck. They were on sale too.

Hotrodz · 11-23-2018, 07:44 PM

Quote:

Originally Posted by Spooler

Went by to get a 5000lb winch and they were all sold out. Just my luck. They were on sale too.

I bought a CHAMPION 3650W/4500W GEN 240V RV generator for $280 from Tractor Trailer Supply.

Sent from my SM-G965U using Tapatalk

Spooler · 11-23-2018, 07:49 PM

Quote:

Originally Posted by Hotrodz

I bought a CHAMPION 3650W/4500W GEN 240V RV generator for $280 from Tractor Trailer Supply.

Sent from my SM-G965U using Tapatalk

That is what I have. It works like a champ and starts the 2nd pull just about everytime.

Spooler · 11-24-2018, 02:08 PM

I got my new CSF radiator and 2 more liters of OS Giken diff fluid today from Z1 Motorsports. I didn't pay for Saturday delivery. Now that's what you call service. WOW.

Spooler · 11-24-2018, 02:11 PM

After Bob's little track fiasco, I am having all of my oil lines upgraded to XRP Racing lines via MA. They are already using them for my fuel system they are building.

URBiN~HURMiT · 11-24-2018, 03:44 PM

Quote:

Originally Posted by Spooler

800hp at the wheel on E85. I won't be going over 19.5psi of boost. So, whatever it makes, it makes. I should be able to hit those numbers on 18.5 psi of boost. I am staying with the stock compression ratio, 11:1.

Just found this thread ... haven't read all the way through it yet but will offer this post for now.
My car is at MA-Motorsports as well.
They built the sleeved block with their design 11:1 CR Pistons and Carrillo H Rods.
JW Stage 2 exhaust cams.
CJM Stage 2 Fuel Rails
CJM Twin 450 Fuel Pumpsl
CJM Intercooler
E-85 flex fue
AAM Stage 2 EFR 71/63 Turbos with external waste gates
AAM upper intake
AAM oil pan
Ecutek Tune
Quaife LSD with MA-M diff cooler
OS Giken twin disc clutch

Dyno'd at 667 rwhp on their Mainline Dyno which reads 17% less than the more common Dyno Jet.
This translated to 780 rwhp on a DynoJet
Calculating BHP using Fuel Flow it came up to 1K BHP. (this factors out to 850 rwhp with a 15% hp loss due to the drivetrain)

4 boost settings on the EVC6 controller = 13 psi spring pressure | 16 psi | 20 psi | 25 psi |
My goal was 800 to 850 rwhp so I'm happy with that. The car is still streetable and reliable.

I did go down to test drive the car a few weeks ago to shake it down and find the little bugs that need attention.

The car is awesome so far - but the turbo's smoke due to poor oil drain - the location and angle of the drain from the turbo's into the oil pan does't allow for sufficient (gravity) drainage.

MA-M will have the car for a little while longer to fix that and to put in a roll bar.

Will be following your build with Great Interest !!!

URBiN~HURMiT · 11-24-2018, 03:58 PM

Quote:

Originally Posted by Rusty

The bad thing is your car sits there while others get worked on. That's one of the things that I don't like about shops. Sometimes they load their selves up with more work then they can handle.

all part of it ... mines been at MA-M for an inch shy of 2 years as well ...
prior to that it was at AAM for almost 2 years as well ...
AAM blew the built motor and tried to cover it up.
That's why it's now at MA-M and I Highly recommend these guys.

You've probably seen my car down there ... it's the PG one with the 17" wheels and big tires.

URBiN~HURMiT · 11-24-2018, 04:13 PM

Quote:

Originally Posted by 370z2Fast

I hear you! I just started my twin turbo build. Bought the AAM Competition kit and can't wait to get this thing done. Rebuilding my engine too

A few pointers with the AAM kit
The location of the turbos aren't conducive for efficient oil drain = turbo smoke
If you have the EFR 71/63's you definitely need the larger I/C and may want to go with external waste gates because they 'modify' the IWG actuator linkage by bending it for clearance.
I've been advised by MA-Motorsports that this can be potentially dangerous.

Good Luck with your build !!!

Spooler · 11-24-2018, 04:14 PM

Quote:

Originally Posted by URBiN~HURMiT

Just found this thread ... haven't read all the way through it yet but will offer this post for now.
My car is at MA-Motorsports as well.
They built the sleeved block with their design 11:1 CR Pistons and Carrillo H Rods.
JW Stage 2 exhaust cams.
CJM Stage 2 Fuel Rails
CJM Twin 450 Fuel Pumpsl
CJM Intercooler
E-85 flex fue
AAM Stage 2 EFR 71/63 Turbos with external waste gates
AAM upper intake
AAM oil pan
Ecutek Tune
Quaife LSD with MA-M diff cooler
OS Giken twin disc clutch

Dyno'd at 667 rwhp on their Mainline Dyno which reads 17% less than the more common Dyno Jet.
This translated to 780 rwhp on a DynoJet
Calculating BHP using Fuel Flow it came up to 1K BHP. (this factors out to 850 rwhp with a 15% hp loss due to the drivetrain)

4 boost settings on the EVC6 controller = 13 psi spring pressure | 16 psi | 20 psi | 25 psi |
My goal was 800 to 850 rwhp so I'm happy with that. The car is still streetable and reliable.

I did go down to test drive the car a few weeks ago to shake it down and find the little bugs that need attention.

The car is awesome so far - but the turbo's smoke due to poor oil drain - the location and angle of the drain from the turbo's into the oil pan does't allow for sufficient (gravity) drainage.

MA-M will have the car for a little while longer to fix that and to put in a roll bar.

Will be following your build with Great Interest !!!

You're the guy that is in my way. LOL I am probably not going to make my HP goals but that is OK. I am going to limit my boost to 18psi since I don't have a closed deck block or an aftermarket intake. We shall see what it makes. I think MA and the machine shop are learning more about these engines as they go and this has delayed mine a bit. I am fine with that. I am expecting to see about 650hp on their dyno. That would be 760hp on a dynojet.

URBiN~HURMiT · 11-24-2018, 04:21 PM

Quote:

Originally Posted by Spooler

Still twiddling my tumbs. Motor is still at the machine shop.

Mine was in the Machine Shop 6 months +
Learned not to count when I'm waiting

Spooler · 11-24-2018, 04:25 PM

Quote:

Originally Posted by URBiN~HURMiT

Mine was in the Machine Shop 6 months +
Learned not to count when I'm waiting

Mine has been in there for 6 months now. It will be there a couple more weeks for sure. I bought a junk yard engine to build off of. Thank goodness I still have my car at home. I will bring it up when they let me know.

URBiN~HURMiT · 11-24-2018, 04:30 PM

Quote:

Originally Posted by Spooler

SEMA will probably mess things up for a week. Not sure if MA is going but I would think they are. They are trying to get one of the cars in the shop finished to make room for me. I will be happy to drag my hooptie up and meet everyone. It will be the first time using the my new trailer. I still need to get a winch and battery installed.

That might be my car they're finishing up ...

URBiN~HURMiT · 11-24-2018, 04:35 PM

Quote:

Originally Posted by Spooler

Still waiting on the motor.... Happy Veterans day everyone. One thing is for sure, you never forget the ladies/fellow's you served with when it got thick. I can still see their faces just like it was yesterday. Wondering how life treated them over the years.

USAF 1966 ~ 1970
Nakhon Phanom RTAFB SEA '69 ~ '70

yep, I'm'a old guy

11-23-2018, 03:04 PM	#361 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,220 Drives: 2011 Nismo GM 6M Rep Power: 2684438	If you don't want to cut holes. Think you will end up with a new hood. Hotrodz likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

11-24-2018, 02:08 PM	#366 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	I got my new CSF radiator and 2 more liters of OS Giken diff fluid today from Z1 Motorsports. I didn't pay for Saturday delivery. Now that's what you call service. WOW. Rusty, Hotrodz and old guy like this.

11-24-2018, 02:11 PM	#367 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	After Bob's little track fiasco, I am having all of my oil lines upgraded to XRP Racing lines via MA. They are already using them for my fuel system they are building. Rusty, Hotrodz and old guy like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Fast Intentions Stage 2 Twin Turbo Kit	Nik@SOHO	Parts for sale (Private Classifieds)	60	10-09-2017 09:11 AM
370Z For Sale 2015 Nismo Tech with Fast Intentions Stage 2 637HP	DPE G	370Z For Sale	2	06-03-2017 12:40 PM
MA Motorsports: FAST Intentions \| HKS \| APEXi \| TANABE	MAMotorsports	Exhaust/Intake	46	05-23-2016 12:12 PM
My 09 NISMO Fast Intentions TT Build	katjmmx	Forced Induction	142	05-19-2016 03:32 PM
[FOR SALE] Fast Intentions Exhaust Build #952 Placement	NismoZ70	Parts for sale (Private Classifieds)	11	03-19-2014 10:27 AM

11-23-2018, 06:55 PM	#363 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	Went by to get a 5000lb winch and they were all sold out. Just my luck. They were on sale too.