Fast Intentions Stage 2 TT build by MA-Motorsports.

Spooler · 05-24-2018, 11:30 AM

I hear ya. I have a 3 day weekend, my diff cooler is going on the car. I will be doing the wiring differently. I refuse to push a switch. I am setting mine up to run off of a thermostat/relay.

Rusty · 05-24-2018, 11:46 AM

Quote:

Originally Posted by Spooler

I hear ya. I have a 3 day weekend, my diff cooler is going on the car. I will be doing the wiring differently. I refuse to push a switch. I am setting mine up to run off of a thermostat/relay.

You have the stock diff cover. So that shouldn't be an issue with using the hoses that came with it. You going to put the temp sensor in a hose? If you do. It will take longer for the heat to reach it, then having it installed in the diff cover.

Spooler · 05-24-2018, 11:57 AM

Quote:

Originally Posted by Rusty

You have the stock diff cover. So that shouldn't be an issue with using the hoses that came with it. You going to put the temp sensor in a hose? If you do. It will take longer for the heat to reach it, then having it installed in the diff cover.

I have the Z1 cover. The temp sensor is at the fitting on the bottom hose. I just have to adjust what temp the cooler comes on. No worries. I have
the same type setup on my Dually's tranny cooler. Works like a charm.

Rusty · 05-24-2018, 12:32 PM

Quote:

Originally Posted by Spooler

I have the Z1 cover. The temp sensor is at the fitting on the bottom hose. I just have to adjust what temp the cooler comes on. No worries. I have
the same type setup on my Dually's tranny cooler. Works like a charm.

With the Z1 cover. You planning on using the top or bottom side port? For the drain port, you using a banjo fitting? Anything else is iffy for ground clearance if you are lowered. You have to watch out for the supply hose routing with the FI exhaust cans. The front of the cooler bracket comes rel close to the cans. I had to rout my hose to the center of the bracket to get it away from the can.

Spooler · 05-24-2018, 12:41 PM

I will be using the bottom side port. All the hoses came with my kit for the Z1 cover. The bottom one is a banjo fitting from what I remember.
I need to go back and check everything. I will be placing an order with Pegusus for additional stuff if needed. I use them also.

Rusty · 05-24-2018, 12:54 PM

At what temp is the senor set for?

Spooler · 05-24-2018, 01:13 PM

Quote:

Originally Posted by Rusty

At what temp is the senor set for?

I will have to look. It came with the kit. I need to see if it has a potentiometer on it to adjust also. If not, I will order what I normally use.

Hotrodz · 05-24-2018, 01:42 PM

Quote:

Originally Posted by Rusty

Thank you.

Glad to be a bad influence.

Give me your credit card. I'll buy what parts I think you need.

My Z is one of my hobbies.

Lol, between my wife and my car, I don't need any help pushing the limits of my credit cards...but thanks for want to help a brother out!

Sent from my SM-G965U using Tapatalk

Spooler · 05-24-2018, 07:21 PM

Quote:

Originally Posted by Hotrodz

That would be it.

Sent from my SM-G965U using Tapatalk

Guess I will need to call them to make me a set when they do yours. LOL It's cheaper for the customer if you do them in bulk. LOL

Spooler · 05-24-2018, 08:06 PM

Quote:

Originally Posted by Rusty

At what temp is the senor set for?

This is what I would normally use.

https://www.summitracing.com/parts/der-16759/overview/

Spooler · 05-25-2018, 01:03 PM

Quote:

Originally Posted by Spooler

This is what I would normally use.

https://www.summitracing.com/parts/der-16759/overview/

I plundered through my diff cooler box last night. I will be ordering a Derale relay to get the job done. I need to order a 2nd one to replace the one that is already on my truck for the A/C condenser fan. It is not working properly when my A/C is on. It has been on the truck since 2006, can't complain.

jchammond · 05-25-2018, 09:13 PM

Quote:

Originally Posted by Spooler

I plundered through my diff cooler box last night. I will be ordering a Derale relay to get the job done. I need to order a 2nd one to replace the one that is already on my truck for the A/C condenser fan. It is not working properly when my A/C is on. It has been on the truck since 2006, can't complain.

Back in the day; Kenworth used an illuminated rocker switch in the dash (2 position).
Down was automatic & up was manual....it illuminated when the fan would come on automatic or illuminated when flipped up to manual.
That's on the old Horton or Bendix air release clutch fans.

Spooler · 05-29-2018, 10:49 AM

I ordered my relay kit from Summit. I hope to have time to deal with it this weekend coming.

Spooler · 05-29-2018, 07:54 PM

I ordered a Zspeed Nismo undertray today. Need to repair the tree limb damage from the Dragon.

Hotrodz · 05-29-2018, 08:09 PM

Quote:

Originally Posted by Spooler

I ordered a Zspeed Nismo undertray today. Need to repair the tree limb damage from the Dragon.

Lol, you should have done that a long time ago. My plastic under tray useless once I got boosted and stated running her hard. It would never stay buttoned up and I wore a big *** hole in it. Between my Zspeed under tray and my aluminum splitter I ain't afraid to scraping at all!

Sent from my SM-G965U using Tapatalk

05-24-2018, 12:41 PM	#170 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,800 Drives: 2013 Nismo 370z Rep Power: 2684392	I will be using the bottom side port. All the hoses came with my kit for the Z1 cover. The bottom one is a banjo fitting from what I remember. I need to go back and check everything. I will be placing an order with Pegusus for additional stuff if needed. I use them also. Rusty likes this. Last edited by Spooler; 05-24-2018 at 12:44 PM.

05-24-2018, 12:54 PM	#171 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,185 Drives: 2011 Nismo GM 6M Rep Power: 2684437	At what temp is the senor set for? __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

05-29-2018, 07:54 PM	#179 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,800 Drives: 2013 Nismo 370z Rep Power: 2684392	I ordered a Zspeed Nismo undertray today. Need to repair the tree limb damage from the Dragon. Hotrodz and jchammond like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Fast Intentions Stage 2 Twin Turbo Kit	Nik@SOHO	Parts for sale (Private Classifieds)	60	10-09-2017 09:11 AM
370Z For Sale 2015 Nismo Tech with Fast Intentions Stage 2 637HP	DPE G	370Z For Sale	2	06-03-2017 12:40 PM
MA Motorsports: FAST Intentions \| HKS \| APEXi \| TANABE	MAMotorsports	Exhaust/Intake	46	05-23-2016 12:12 PM
My 09 NISMO Fast Intentions TT Build	katjmmx	Forced Induction	142	05-19-2016 03:32 PM
[FOR SALE] Fast Intentions Exhaust Build #952 Placement	NismoZ70	Parts for sale (Private Classifieds)	11	03-19-2014 10:27 AM

05-24-2018, 11:30 AM	#166 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,800 Drives: 2013 Nismo 370z Rep Power: 2684392	I hear ya. I have a 3 day weekend, my diff cooler is going on the car. I will be doing the wiring differently. I refuse to push a switch. I am setting mine up to run off of a thermostat/relay.

05-29-2018, 10:49 AM	#178 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,800 Drives: 2013 Nismo 370z Rep Power: 2684392	I ordered my relay kit from Summit. I hope to have time to deal with it this weekend coming.