Fast Intentions Stage 2 TT build by MA-Motorsports.

Spooler · 03-06-2018, 02:03 PM

I am creating a TT build thread to pass the time and passing the time is brutal. So, I am going to list out what I am doing.

Fast Intentions Stage 2.5 TT kit
Fast Intentions Crash bar
Fast Intentions 3" exhaust with Carbon Fiber mufflers
ATS Triple Carbon Clutch with external Nissan CSC
2-Walboro 450
CJ Motorsports duel fuel pump setup
IDA1700cc injectors
MA-Motorsports custom built fuel return system for E85
JWT C2 exhaust cams with new water pump, Timing chains, Guides and tensioners
Upgraded front cover Oil galley gaskets/fasteners
Suckerpunch oil pump
MA-Motorsports ATI fluid damper (already on the car)
CJ Motorsports baffled oil pan (already on the car)
34 row FI oil cooler (already on the car)
Carrillo Pro Rods
MA-Motorsports Diamond Forged pistons
Compression will stay at stock 11 to 1
OS Giken 1.5 LSD (already on the car)
Z1 Motorsports Poly Diff bushings (already on the car)
MA-Motorsports Diff cooler
Finite Element Design Carbon Fiber 3" cooling ducts
"Looking for 3" front brake backing plates"
Z1 2-piece rotors front and rear (already on the car)
Carbotech XP8 pads front/rear (already on the car)
E85 content gauge, etc.
Eboost2 boost controller/gauge
Galeforce custom single gauge pillar
Ecuteck tuning with Flexfuel
Junk Yard long block
DSS Pro Level Axles

I am building the motor with Carrillo rods and Ma-Motorsports custom Forged pistons, etc.

goeagles11 · 03-06-2018, 02:35 PM

What are your whp and lb-fts torque goals?

Spooler · 03-06-2018, 02:42 PM

The end goal is 800-850hp. I won't be able to do that until after building the engine. For now, it will be 590hp on 93 octane and 650hp on E85 (Ignite E90). The numbers are normal DynoJet numbers. Torque will be limited to 580tq or under. The limiting factor is going to be the torque. It depends on how well the torque can be pushed up in the upper RPM range. Be for warned, Ma-Motorsport dyno reads real low. That will be taken into account when HP/Torque numbers are posted up.

Spooler · 03-06-2018, 02:51 PM

I thought very hard about going with the FI Stage 2.5 with larger turbo's. I just don't feel they are necessary for my goals. The install will be sometime after Zdayz.

Hotrodz · 03-06-2018, 05:22 PM

You should also add a ported lower manifold and cpt.obvious upper manifold. Also you did not mention replacing oil pump gear. Got have all the high horse power go fast parts.

Sent from my SM-N910P using Tapatalk

Spooler · 03-06-2018, 05:25 PM

Quote:

Originally Posted by Hotrodz

You should also add a ported lower manifold and cpt.obvious upper manifold. Also you did not mention replacing oil pump gear. Got have all the high horse power go fast parts.

Sent from my SM-N910P using Tapatalk

Suckerpunch oil pump baby. Ported lower manifold, Hmm. Haven't thought about that.

Hotrodz · 03-06-2018, 05:28 PM

Quote:

Originally Posted by Spooler

Suckerpunch oil pump baby. Ported lower manifold, Hmm. Haven't thought about that.

I have a ported lower. I will get an upper when I build my motor.

Sent from my SM-N910P using Tapatalk

Trips · 03-06-2018, 07:50 PM

You're going to start snapping axles at those HP numbers once its staring to hookup.

Problems I'd love to have

Spooler · 03-06-2018, 08:23 PM

Quote:

Originally Posted by Trips

You're going to start snapping axles at those HP numbers once its staring to hookup.

Problems I'd love to have

There is an upgrade for that.

Hotrodz said I could try his out first.

SS_Firehawk · 03-06-2018, 08:43 PM

You're Specialty Z clutch comes with a new Tilton Slave

Sell that CSC you have

SS_Firehawk · 03-06-2018, 08:47 PM

I'm having my C2 cams done before boost, but it looks really close to the same direction I've been moving. I've done my bushings, diff, mounts, clutch, flywheel, crash bar, cooling ducts, and pads. I have Heads, cams, damper, oil pump gears, and looking at picking up the CJM fueling stuff for E85. Big diff is I'm spending to have the heads ported, then maybe boost and/or build the bottom end.

This will give me a good picture of what I'm looking at. I'm watching this

Spooler · 03-06-2018, 09:18 PM

Quote:

Originally Posted by SS_Firehawk

I'm having my C2 cams done before boost, but it looks really close to the same direction I've been moving. I've done my bushings, diff, mounts, clutch, flywheel, crash bar, cooling ducts, and pads. I have Heads, cams, damper, oil pump gears, and looking at picking up the CJM fueling stuff for E85. Big diff is I'm spending to have the heads ported, then maybe boost and/or build the bottom end.

This will give me a good picture of what I'm looking at. I'm watching this

I want to build the motor too. I am thinking on it still. I just hate to waste 50k miles of good motor. I may like it at that pre built motor level and not want to go higher. We shall see. I am a boost addict just like everyone else, I doubt it.

elperuano · 03-06-2018, 09:32 PM

Nice build sheet! I'd say go for the rebuild while it's all out. Save time and money. If you're a boost addict like the rest of us, that power will feel slow in a week and you're gonna want more!

Hotrodz · 03-06-2018, 09:41 PM

Quote:

Originally Posted by Spooler

I want to build the motor too. I am thinking on it still. I just hate to waste 50k miles of good motor. I may like it at that pre built motor level and not want to go higher. We shall see. I am a boost addict just like everyone else, I doubt it.

I have been boosted for about 4.5 years and I have about 55K on the motor and about 35k boosted. You know how I drive...a lot like you. She does not get babied. I am torn with the same thinking do I build sooner than later knowing there is good life in the motor but 35k miles boosted with a few thousand at the track well I would say the motor is like 75 or 80K. I would say if you got the cash do it now and be done. Doing it later just mean more money and down time. Just my two cent.

jchammond · 03-06-2018, 09:43 PM

Don’t Destroy MA’s Dyno!

Sent from my iPad using Tapatalk

03-06-2018, 02:03 PM	#1 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,832 Drives: 2013 Nismo 370z Rep Power: 2684392	Fast Intentions Stage 2 TT build by MA-Motorsports. I am creating a TT build thread to pass the time and passing the time is brutal. So, I am going to list out what I am doing. Fast Intentions Stage 2.5 TT kit Fast Intentions Crash bar Fast Intentions 3" exhaust with Carbon Fiber mufflers ATS Triple Carbon Clutch with external Nissan CSC 2-Walboro 450 CJ Motorsports duel fuel pump setup IDA1700cc injectors MA-Motorsports custom built fuel return system for E85 JWT C2 exhaust cams with new water pump, Timing chains, Guides and tensioners Upgraded front cover Oil galley gaskets/fasteners Suckerpunch oil pump MA-Motorsports ATI fluid damper (already on the car) CJ Motorsports baffled oil pan (already on the car) 34 row FI oil cooler (already on the car) Carrillo Pro Rods MA-Motorsports Diamond Forged pistons Compression will stay at stock 11 to 1 OS Giken 1.5 LSD (already on the car) Z1 Motorsports Poly Diff bushings (already on the car) MA-Motorsports Diff cooler Finite Element Design Carbon Fiber 3" cooling ducts "Looking for 3" front brake backing plates" Z1 2-piece rotors front and rear (already on the car) Carbotech XP8 pads front/rear (already on the car) E85 content gauge, etc. Eboost2 boost controller/gauge Galeforce custom single gauge pillar Ecuteck tuning with Flexfuel Junk Yard long block DSS Pro Level Axles I am building the motor with Carrillo rods and Ma-Motorsports custom Forged pistons, etc. gbrettin, JARblue, Total D and 10 others like this. Last edited by Spooler; 05-23-2019 at 02:31 PM.

03-06-2018, 02:42 PM	#3 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,832 Drives: 2013 Nismo 370z Rep Power: 2684392	The end goal is 800-850hp. I won't be able to do that until after building the engine. For now, it will be 590hp on 93 octane and 650hp on E85 (Ignite E90). The numbers are normal DynoJet numbers. Torque will be limited to 580tq or under. The limiting factor is going to be the torque. It depends on how well the torque can be pushed up in the upper RPM range. Be for warned, Ma-Motorsport dyno reads real low. That will be taken into account when HP/Torque numbers are posted up. GaleForce and Rusty like this. Last edited by Spooler; 03-06-2018 at 03:37 PM.

03-06-2018, 02:51 PM	#4 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,832 Drives: 2013 Nismo 370z Rep Power: 2684392	I thought very hard about going with the FI Stage 2.5 with larger turbo's. I just don't feel they are necessary for my goals. The install will be sometime after Zdayz. Rusty and redondoaveb like this.

03-06-2018, 05:22 PM	#5 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	You should also add a ported lower manifold and cpt.obvious upper manifold. Also you did not mention replacing oil pump gear. Got have all the high horse power go fast parts. Sent from my SM-N910P using Tapatalk GaleForce likes this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

03-06-2018, 07:50 PM	#8 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,732 Drives: 🔰 Rep Power: 10	You're going to start snapping axles at those HP numbers once its staring to hookup. Problems I'd love to have BOLIO 671, Rusty, Hotrodz and 3 others like this. __________________

03-06-2018, 02:35 PM	#2 (permalink)
goeagles11 Base Member Join Date: May 2017 Location: South Florida Posts: 81 Drives: 2017 370z Sport Rep Power: 8	What are your whp and lb-fts torque goals?

03-06-2018, 08:43 PM	#10 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7335	You're Specialty Z clutch comes with a new Tilton Slave Sell that CSC you have __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

03-06-2018, 08:47 PM	#11 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7335	I'm having my C2 cams done before boost, but it looks really close to the same direction I've been moving. I've done my bushings, diff, mounts, clutch, flywheel, crash bar, cooling ducts, and pads. I have Heads, cams, damper, oil pump gears, and looking at picking up the CJM fueling stuff for E85. Big diff is I'm spending to have the heads ported, then maybe boost and/or build the bottom end. This will give me a good picture of what I'm looking at. I'm watching this Rusty and Stright_Drop like this. __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

03-06-2018, 09:32 PM	#13 (permalink)
elperuano A True Z Fanatic Join Date: Oct 2011 Location: Southwest FL Posts: 1,374 Drives: G37S Rep Power: 29	Nice build sheet! I'd say go for the rebuild while it's all out. Save time and money. If you're a boost addict like the rest of us, that power will feel slow in a week and you're gonna want more!

03-06-2018, 09:43 PM	#15 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684395	Don’t Destroy MA’s Dyno! Sent from my iPad using Tapatalk Hotrodz likes this. __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Fast Intentions Stage 2 Twin Turbo Kit	Nik@SOHO	Parts for sale (Private Classifieds)	60	10-09-2017 09:11 AM
370Z For Sale 2015 Nismo Tech with Fast Intentions Stage 2 637HP	DPE G	370Z For Sale	2	06-03-2017 12:40 PM
MA Motorsports: FAST Intentions \| HKS \| APEXi \| TANABE	MAMotorsports	Exhaust/Intake	46	05-23-2016 12:12 PM
My 09 NISMO Fast Intentions TT Build	katjmmx	Forced Induction	142	05-19-2016 03:32 PM
[FOR SALE] Fast Intentions Exhaust Build #952 Placement	NismoZ70	Parts for sale (Private Classifieds)	11	03-19-2014 10:27 AM