Topgunz full supercharger kits!!

turtle64b · 07-15-2018, 08:27 PM

I just swapped out my SC-side pulleys for the Vortech high-traction and the larger idler. Wasn't terribly difficult. I fashioned my own spacer out of a 3/4" x 1" x 1" steel spacer from Lowe's. The shaft is 0.785" and the required spacing is 3/8", just FYI. I cut the spacer to 3/8" and dremelled out the inner surface until it fit on snugly with a little effort. Remember, the idler pulley also needs a 3/8" spacer (or washers, since they don't spin)!!!

I bought a 3/8-24 x 2" bolt for the jackshaft and I used the old jackshaft bolt for the new SC pulley.

Also FYI, I had an old 8-rib belt lying around that I used to wrap the SC pulley while loosening the pulley bolt.

I can get pictures of the specifics, if desired.

redondoaveb · 07-15-2018, 08:49 PM

Quote:

Originally Posted by turtle64b

I just swapped out my SC-side pulleys for the Vortech high-traction and the larger idler. Wasn't terribly difficult. I fashioned my own spacer out of a 3/4" x 1" x 1" steel spacer from Lowe's. The shaft is 0.785" and the required spacing is 3/8", just FYI. I cut the spacer to 3/8" and dremelled out the inner surface until it fit on snugly with a little effort. Remember, the idler pulley also needs a 3/8" spacer (or washers, since they don't spin)!!!

I bought a 3/8-24 x 2" bolt for the jackshaft and I used the old jackshaft bolt for the new SC pulley.

Also FYI, I had an old 8-rib belt lying around that I used to wrap the SC pulley while loosening the pulley bolt.

I can get pictures of the specifics, if desired.

I already have the spacer from 928, thanks for the info on it needing to be 3/8" and the bolt length, good info. I was going to use washers on the idler pulley.

EVOHUNTER · 07-16-2018, 10:26 AM

i cannot believe how far you have come with this kit Topz, its been 2 years since ive been around here lol. kudos.

TopgunZ · 07-16-2018, 12:30 PM

Quote:

Originally Posted by EVOHUNTER

i cannot believe how far you have come with this kit Topz, its been 2 years since ive been around here lol. kudos.

No kidding. THere must be an empty grave somewhere up there.

Are you still on the Stillen?

EVOHUNTER · 07-16-2018, 02:34 PM

Yes i do, its been sitting for 2 years now LOL!

Im having it tuned this week. hopefully my fuel system holds, stock jack and stock serp side, 2.80" on blower with low/mid range impeller.

I like that little tensioner/pulley for the serp side belt, can you sell me that little piece? lol
i bet that baby helps with belt slippage

batboyvaj · 07-16-2018, 10:39 PM

Do you have anyone running this kit with a TI trim? Or a V2 head unit?

TopgunZ · 07-17-2018, 07:56 AM

Quote:

Originally Posted by batboyvaj

Do you have anyone running this kit with a TI trim? Or a V2 head unit?

Not that I am aware of.

Ezemaxima · 07-20-2018, 04:24 AM

Quote:

Originally Posted by TopgunZ

Not that I am aware of.

Would you sell the kit without the Stillen intake manifold, i wanna run a GTR R35 intake manifold with RJM adaptor?

nizzan4u2nv · 07-20-2018, 05:13 PM

Quote:

Originally Posted by Ezemaxima

Would you sell the kit without the Stillen intake manifold, i wanna run a GTR R35 intake manifold with RJM adaptor?

Not gonna work...

wideglideleon · 07-20-2018, 06:14 PM

will not work!

G3RSTY7 · 07-23-2018, 12:48 PM

Quote:

Originally Posted by nizzan4u2nv

Not gonna work...

IDK pretty sure Brian Burton was running that with his A-A setup on his G. I’ll ask

nizzan4u2nv · 07-23-2018, 02:58 PM

Quote:

Originally Posted by G3RSTY7

IDK pretty sure Brian Burton was running that with his A-A setup on his G. I’ll ask

It could work but not as simply as swapping the manifolds. The entire cold side piping would have to be redone.

redondoaveb · 07-23-2018, 03:16 PM

I believe this is a picture of Brian's G.

G3RSTY7 · 07-23-2018, 03:54 PM

Yep can be done but definitely not cheap. Will add a few thousand to your build cost with just the manifold and adapters alone (they do sell it). And then the piping fab—all for just cosmetic. I’d put that money to wheels or bodywork instead. I’ll post up if Brian gets back to me about it I know he was trying to sell his a while back. I think he was selling his entire kit for $7k though so if that includes piping not as bad

Ezemaxima · 07-24-2018, 11:40 PM

Quote:

Originally Posted by nizzan4u2nv

Not gonna work...

I know it's not going to bolt on cause it's going to be installed on a 2009 M35 but his kit will be the base and I will make necessary adjustments and mods to make it work. I know the sc bracket will bolt on. New pipings n brackets at least is needed to make it work.

07-16-2018, 10:26 AM	#198 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 15	i cannot believe how far you have come with this kit Topz, its been 2 years since ive been around here lol. kudos. ZontheRocks likes this. __________________

07-16-2018, 02:34 PM	#200 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 15	Yes i do, its been sitting for 2 years now LOL! Im having it tuned this week. hopefully my fuel system holds, stock jack and stock serp side, 2.80" on blower with low/mid range impeller. I like that little tensioner/pulley for the serp side belt, can you sell me that little piece? lol i bet that baby helps with belt slippage __________________ Last edited by EVOHUNTER; 07-16-2018 at 02:38 PM.

07-23-2018, 03:54 PM	#209 (permalink)
G3RSTY7 Base Member Join Date: Aug 2017 Location: Colorado Posts: 103 Drives: Infiniti G37s 6MT Rep Power: 8	Yep can be done but definitely not cheap. Will add a few thousand to your build cost with just the manifold and adapters alone (they do sell it). And then the piping fab—all for just cosmetic. I’d put that money to wheels or bodywork instead. I’ll post up if Brian gets back to me about it I know he was trying to sell his a while back. I think he was selling his entire kit for $7k though so if that includes piping not as bad __________________ 09 G37S RWD 6MT, Topgunz Supercharger, CJM RFS, Walbro 450, 1050x, Nismo 1.5way LSD, Ecutek FF tuned by Seb IG: G3RSTY7 MyG37.com: RickyBobby Last edited by G3RSTY7; 07-23-2018 at 03:58 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
street /carb legal turbo or supercharger kits	pyrrhus17	Engine & Drivetrain	9	03-08-2023 06:37 PM
2012-2016 Nismo STILLEN Supercharger Kits on Sale!	Team_STILLEN	Sponsor Classifieds	0	07-12-2016 03:05 PM
STILLEN Supercharger 2009-2011 370Z kits - $500 off!	Team_STILLEN	Sponsor Classifieds	3	06-19-2016 02:06 PM
[FOR SALE] stilllen supercharger full kit.	btimola	Parts for sale (Private Classifieds)	22	12-14-2014 09:23 PM
GTM Performance Engineering stage 2 600hp supercharger kits line-up press release	SAM@GTM	Forced Induction	305	09-27-2012 04:23 PM

07-16-2018, 10:39 PM	#201 (permalink)
batboyvaj Base Member Join Date: Jun 2011 Location: mn Posts: 111 Drives: 2011 370z Rep Power: 14	Do you have anyone running this kit with a TI trim? Or a V2 head unit?

07-20-2018, 06:14 PM	#205 (permalink)
wideglideleon Track Member Join Date: Apr 2015 Location: Tucson AZ Posts: 569 Drives: SC 09 370Z LG 7AT Rep Power: 64085	will not work!