Low oil pressure!

jmroy6 · 02-17-2018, 09:59 PM

Quick update:

Finally ripped the car apart today, oil galley gaskets were all intact, looks like this motor got the updated versions because they were some composite metal material instead of the old paper style. Anyway i didn't take it apart for no reason even though the gaskets didnt fail, the shitty fasteners did. On the upper galley two fastener were less than hand tight. So this is why i was getting low oil pressure drops, but no ecm codes (p0011,p0021)

Rusty · 02-18-2018, 12:02 AM

Very lucky that they didn't back all the way out and land in the timing chain.

Spooler · 02-18-2018, 10:40 PM

Quote:

Originally Posted by jmroy6

Quick update:

Finally ripped the car apart today, oil galley gaskets were all intact, looks like this motor got the updated versions because they were some composite metal material instead of the old paper style. Anyway i didn't take it apart for no reason even though the gaskets didnt fail, the shitty fasteners did. On the upper galley two fastener were less than hand tight. So this is why i was getting low oil pressure drops, but no ecm codes (p0011,p0021)

Due to this reason right here I am going to have mine done when I get my TT install done. Might as well do exhaust cams and an oil pump upgrade too. The motor will be out, why not.

Rusty · 02-18-2018, 11:20 PM

Quote:

Originally Posted by Spooler

Due to this reason right here I am going to have mine done when I get my TT install done. Might as well do exhaust cams and an oil pump upgrade too. The motor will be out, why not.

This is on my to do list.

NissanTracker · 03-03-2018, 09:11 PM

Quote:

Originally Posted by jmroy6

Quick update:
On the upper galley two fastener were less than hand tight. So this is why i was getting low oil pressure drops, but no ecm codes (p0011,p0021)

Looks like it was replaced and the mechanic didn't torque them down correctly?

Spooler · 03-03-2018, 11:08 PM

Quote:

Originally Posted by NissanTracker

Looks like it was replaced and the mechanic didn't torque them down correctly?

Noop, common issue.

jmroy6 · 03-03-2018, 11:23 PM

Nope, this was the first time the motor has been apart since i bought it. the two of the fasteners circled in red backed out on upper galley.

Quote:

Originally Posted by NissanTracker

Looks like it was replaced and the mechanic didn't torque them down correctly?

jmroy6 · 03-04-2018, 04:29 PM

Added DIY thread

http://www.the370z.com/engine-drivet...ml#post3735570

gbrettin · 03-05-2018, 05:10 PM

I've read too many horror stories about the oil galley gaskets going out. I ordered EPS's kit:

https://www.facebook.com/epstuningtx/

ht4e · 06-20-2018, 01:22 PM

Quote:

Originally Posted by jmroy6

Quick update:

Finally ripped the car apart today, oil galley gaskets were all intact, looks like this motor got the updated versions because they were some composite metal material instead of the old paper style. Anyway i didn't take it apart for no reason even though the gaskets didnt fail, the shitty fasteners did. On the upper galley two fastener were less than hand tight. So this is why i was getting low oil pressure drops, but no ecm codes (p0011,p0021)

Thanks for the DIY, I am glad you got it resolved. Based on the profile, I am assuming you are SC?
I am looking into a Z, and previously had a BRZ but the oil pressure light/ oil level never came on then boom the motor spun a bearing. When the motor was removed to assess the damage, there was no oil in the oil pan...
I wonder if any of these manufacture sensors are truly functional...

Spooler · 06-20-2018, 02:48 PM

Quote:

Originally Posted by ht4e

Thanks for the DIY, I am glad you got it resolved. Based on the profile, I am assuming you are SC?
I am looking into a Z, and previously had a BRZ but the oil pressure light/ oil level never came on then boom the motor spun a bearing. When the motor was removed to assess the damage, there was no oil in the oil pan...
I wonder if any of these manufacture sensors are truly functional...

There is no gauge or light that will replace checking your oil. Once the light comes on or the oil pressure drops, it is too late. The damage is done.

Rusty · 06-20-2018, 08:17 PM

Normal idle oil pressure is about 35 lbs. I have the warning light on my gauge set at 30 lbs. Hopefully if anything happens. I will be able to shut it down before damage. The factory warning light pops on at about 5 lbs.

Jayhovah · 06-21-2018, 03:50 PM

Quote:

Originally Posted by Rusty

Normal idle oil pressure is about 35 lbs. I have the warning light on my gauge set at 30 lbs. Hopefully if anything happens. I will be able to shut it down before damage. The factory warning light pops on at about 5 lbs.

Since the OEM sensor is just a switch... I wonder if maybe we can replace it with one that has a more meaningful threshold (like the 30# you have your warning set to).

SouthArk370Z · 06-21-2018, 04:09 PM

Quote:

Originally Posted by Jayhovah

Since the OEM sensor is just a switch... I wonder if maybe we can replace it with one that has a more meaningful threshold (like the 30# you have your warning set to).

Yes you can - as long as it's a mechanical switch and compatible with engine oil. Might have to use an adapter to match pipe threads. If you can figure out which sending unit has the setting you want, it should be an easy job. You may be able to order what you need from McMaster-Carr, et al.

Edit: And the switch action (NO or NC) needs to match.

filip00 · 11-16-2021, 06:19 AM

Hey guys, one question regarding the part number. I'm scheduling a preventative gallery gasket replacement and I have ordered the gallery gaskets as per the part number: 13533-JK21A. The part arrived and the guys at Nissan tell me that the part which arrived doesn't quite seem like it's fully metal - more like mixture of paper-like gasket as well as the metal one. Is that OK? I mean, are the renewed gaskets FULLY metal, or are they more like a mixture of both?

Thanks for the info!

02-17-2018, 09:59 PM	#31 (permalink)
jmroy6 Base Member Join Date: Sep 2015 Location: CT Posts: 179 Drives: Spirited Rep Power: 235	Quick update: Finally ripped the car apart today, oil galley gaskets were all intact, looks like this motor got the updated versions because they were some composite metal material instead of the old paper style. Anyway i didn't take it apart for no reason even though the gaskets didnt fail, the shitty fasteners did. On the upper galley two fastener were less than hand tight. So this is why i was getting low oil pressure drops, but no ecm codes (p0011,p0021) Rusty likes this. __________________ 2012 370z GTM SC Last edited by jmroy6; 02-17-2018 at 10:01 PM.

02-18-2018, 12:02 AM	#32 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,172 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Very lucky that they didn't back all the way out and land in the timing chain. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

03-04-2018, 04:29 PM	#38 (permalink)
jmroy6 Base Member Join Date: Sep 2015 Location: CT Posts: 179 Drives: Spirited Rep Power: 235	Added DIY thread http://www.the370z.com/engine-drivet...ml#post3735570 Rusty likes this. __________________ 2012 370z GTM SC

03-05-2018, 05:10 PM	#39 (permalink)
gbrettin A True Z Fanatic Join Date: Oct 2010 Location: Portage, MI Posts: 2,279 Drives: Tricycle Rep Power: 589151	I've read too many horror stories about the oil galley gaskets going out. I ordered EPS's kit: https://www.facebook.com/epstuningtx/ GaleForce and Rusty like this.

06-20-2018, 08:17 PM	#42 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,172 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Normal idle oil pressure is about 35 lbs. I have the warning light on my gauge set at 30 lbs. Hopefully if anything happens. I will be able to shut it down before damage. The factory warning light pops on at about 5 lbs. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

11-16-2021, 06:19 AM	#45 (permalink)
filip00 Track Member Join Date: May 2021 Location: slovenia Posts: 556 Drives: 370z pack Rep Power: 125427	Hey guys, one question regarding the part number. I'm scheduling a preventative gallery gasket replacement and I have ordered the gallery gaskets as per the part number: 13533-JK21A. The part arrived and the guys at Nissan tell me that the part which arrived doesn't quite seem like it's fully metal - more like mixture of paper-like gasket as well as the metal one. Is that OK? I mean, are the renewed gaskets FULLY metal, or are they more like a mixture of both? Thanks for the info! Last edited by filip00; 11-16-2021 at 08:00 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Zero oil pressure	bimbimbop	Forced Induction	9	11-01-2017 12:36 AM
Tire pressure	vikingpilot	Wheels & Tires	4	03-17-2017 04:39 AM
Low Oil Pressure Light? Help please!	NismoZ370	Engine & Drivetrain	9	06-15-2016 11:46 PM
[FOR SALE] AEM Oil Pressure Sensor	40 to 332	Parts for sale (Private Classifieds)	0	09-13-2015 01:35 PM
Oil Pressure Gauge	jpit	Engine & Drivetrain	3	03-16-2010 10:33 PM