Preparation for the STILLEN supercharger

jmlenz · 03-10-2010, 06:51 PM

Quote:

Originally Posted by MMC Racing

I don't think this has been asked - what PSI is that dyno at?

Thems is fightin words!

Buddy Revell · 03-10-2010, 10:34 PM

Quote:

Originally Posted by MMC Racing

I don't think this has been asked - what PSI is that dyno at?

Apparently, someone HAS been using the ignore button.

ChrisSlicks · 03-10-2010, 11:00 PM

Quote:

Originally Posted by 370z4Steve

looks like a basic 3:1 ratio 91 to 100

4:1. You want the err on the low side for tuning.

1slow370 · 03-11-2010, 04:42 AM

Quote:

Originally Posted by RCZ

I think we could get away with 10 psi on a good 93oct tune. As far as being maxed out, I don't think the Stillen kit is near maxed out. As I understand it, they have enough room on that compressor to go well beyond the limit of our internals.

Anyone know what the max psi is for that blower?

I mean that it is maxed out in the sense that after purchase of said kit it is going to cost you like another 6grand to safely up the power. hell if you don't change your clutchand flywheel just buying one of those kits is already over the max the car will take. I like to work in terms of the package as a whole. I think 10 psi would be doable as a race tune but i shure as hell would pulley down to no more than 6-8 for regular use. 10 psi is def. meth injection territory to me. hell i'd think of putting meth on an n/a car just so i could run a nitro booster in it. i'd try to find the most oxygenated shyt i could find.

G35s-Q8 · 03-11-2010, 06:40 AM

So, i have some questions here for Kyle&Josh@Stillen, are you going to send out the S/C kits with uni-chip or control box just like you did the the old 350z S/C?
Or are you planning to use Osiris UpRev reflash and tune?
Do you thing the UpRev is better than uni-chip for tuning?
And what made you go with that route for the tuning? (uni-chip vs uprev tuning).

RCZ · 03-11-2010, 09:19 AM

^ You're gonna have to wait for the release like all of us. It should be coming soon.

CinZinnati · 03-11-2010, 09:43 AM

So, I have a couple simpler questions. Kyle seemed to suggest that if you haven't done anything to your car yet...don't. But for those of us who have, I'm curious as to why there would by any issue with for example HFC's. I understand the headers, but isn't a less restrictive exhaust good no matter what..or is just a tuning thing because they aren't testing the car with these particular types of setups? And for those of use who have the Gen 3 intakes, what's the best option since we gotta rip 'em out

G Fo12ce · 03-11-2010, 10:58 AM

If you go Supercharger, I think this is the best option for your intake:HERE

Zsteve · 03-11-2010, 11:24 AM

arent both systems developing thier own intake, to fit the SC system, Im sure piping is different now. And he said a CBE is fine.

RCZ · 03-11-2010, 11:44 AM

Quote:

Originally Posted by CinZinnati

So, I have a couple simpler questions. Kyle seemed to suggest that if you haven't done anything to your car yet...don't. But for those of us who have, I'm curious as to why there would by any issue with for example HFC's. I understand the headers, but isn't a less restrictive exhaust good no matter what..or is just a tuning thing because they aren't testing the car with these particular types of setups? And for those of use who have the Gen 3 intakes, what's the best option since we gotta rip 'em out

From what I remember Kyle was specifically talking about the headers. Everything else is fine...You will not be able to use your G3's, so you should maybe start selling them soon. Leave whatever exhaust you have on, that will be fine. The thing is that any time you free up the exhaust with headers, hfc's and whatever else, you will see small increments in peak boost. You should be fine either way...I wouldnt worry about it. Specially if you are not getting the CARB kit.

Silo · 03-11-2010, 11:53 AM

Quote:

Originally Posted by RCZ

. The thing is that any time you free up the exhaust with headers, hfc's and whatever else, you will see small increments in peak boost.

That's the case with turbos, but not with superchargers. Superchargers make their peak boost at rpm redline. They are not "load" dependant like turbos nor will the reduced backpressure on the "exhaust side" change the pressure ratios since there simply is no exhaust housing on a supercharger.

Kyle@STILLEN · 03-11-2010, 12:09 PM

Quote:

Originally Posted by 1slow370

I mean that it is maxed out in the sense that after purchase of said kit it is going to cost you like another 6grand to safely up the power. hell if you don't change your clutchand flywheel just buying one of those kits is already over the max the car will take. I like to work in terms of the package as a whole. I think 10 psi would be doable as a race tune but i shure as hell would pulley down to no more than 6-8 for regular use. 10 psi is def. meth injection territory to me. hell i'd think of putting meth on an n/a car just so i could run a nitro booster in it. i'd try to find the most oxygenated shyt i could find.

There will be room to gain more power with either kit I'm sure. GTM has already announced that they feel comfortable running more boost with their kit and just like our 350Z/G35 kit ours will be able to run more safely later on.

Quote:

Originally Posted by G35s-Q8

So, i have some questions here for Kyle&Josh@Stillen, are you going to send out the S/C kits with uni-chip or control box just like you did the the old 350z S/C?
Or are you planning to use Osiris UpRev reflash and tune?
Do you thing the UpRev is better than uni-chip for tuning?
And what made you go with that route for the tuning? (uni-chip vs uprev tuning).

This will be a part of the press release which will be coming soon. We used a piggy back system on our superchargers for the VQ35 and the VK56 (Titan, Armada) engines but it was not the Unichip offering.

Quote:

Originally Posted by CinZinnati

So, I have a couple simpler questions. Kyle seemed to suggest that if you haven't done anything to your car yet...don't. But for those of us who have, I'm curious as to why there would by any issue with for example HFC's. I understand the headers, but isn't a less restrictive exhaust good no matter what..or is just a tuning thing because they aren't testing the car with these particular types of setups? And for those of use who have the Gen 3 intakes, what's the best option since we gotta rip 'em out

Sorry if I gave the impression that you shouldn't do anything to your car. You absolutely should prepare the car with a cat-back exhaust, clutch and flywheel, suspension, brakes, and more. I just don't recommend installing headers (shorty's or long tube's) until we have a chance to test it. We saw on the VQ35 supercharger that you could lose up to a pound of boost by installing headers. They did improve efficiency though so you would make more horsepower. It was a weird trade off but basically in the end you did not make any more power on the dyno. However, everyone who drove with that setup acknowledged that there was a definite improvement in throttle response.

Basically...We just don't recommend installing headers until we have the opportunity to test them for you.

Quote:

Originally Posted by Silo

That's the case with turbos, but not with superchargers. Superchargers make their peak boost at rpm redline. They are not "load" dependant like turbos nor will the reduced backpressure on the "exhaust side" change the pressure ratios since there simply is no exhaust housing on a supercharger.

You are correct. Superchargers continue building boost all the way to RPM redline. However, we have seen where installing headers can drop up to a pound of boost because of the reduction in back pressure.

Silo · 03-11-2010, 12:21 PM

Quote:

Originally Posted by Kyle@STILLEN

You are correct. Superchargers continue building boost all the way to RPM redline. However, we have seen where installing headers can drop up to a pound of boost because of the reduction in back pressure.

Exactly... "drop"! RCZ was talking about increase. By the way, the boost drop on your 350Z s/c is is pretty much a screw-type blower issue only as it is an air pump rather than a compressor.

Kyle@STILLEN · 03-11-2010, 12:35 PM

Quote:

Originally Posted by Silo

Exactly... "drop"! RCZ was talking about increase. By the way, the boost drop on your 350Z s/c is is pretty much a screw-type blower issue only as it is an air pump rather than a compressor.

Exactly. We aren't expecting an issue with the Vortech unit but we also don't want to promise anything to anyone until we have the opportunity to test it. One thing we noticed was that the VK56 did not lose any boost with the long tube cat delete headers that we made but it did run a bit lean. The 350Z/G35 supercharger on the other hand did drop boost but the a/f ratio was fine.

Each engine reacts a little bit differently so we're just playin' it safe.

RCZ · 03-11-2010, 12:45 PM

Oops, thats right, was trying to help quick before I had to run out and was thinking turbo instead of sc. My bad.

03-11-2010, 09:43 AM	#1042 (permalink)
CinZinnati Base Member Join Date: Apr 2009 Location: Cincinnati Age: 45 Posts: 28 Drives: 09 Solid Red 370z Rep Power: 16	So, I have a couple simpler questions. Kyle seemed to suggest that if you haven't done anything to your car yet...don't. But for those of us who have, I'm curious as to why there would by any issue with for example HFC's. I understand the headers, but isn't a less restrictive exhaust good no matter what..or is just a tuning thing because they aren't testing the car with these particular types of setups? And for those of use who have the Gen 3 intakes, what's the best option since we gotta rip 'em out __________________ '09 Solid Red 370z with Stillen CBE, HFC's, and Gen 3 air intakes

03-11-2010, 10:58 AM	#1043 (permalink)
G Fo12ce Premium Member Join Date: Nov 2009 Location: Socal Posts: 996 Drives: Sold! Rep Power: 52	If you go Supercharger, I think this is the best option for your intake:HERE __________________ Nismo Suspension: New Owners Check Here!

03-11-2010, 11:24 AM	#1044 (permalink)
Zsteve A True Z Fanatic Join Date: Sep 2009 Location: TX Posts: 3,298 Drives: the 2 balled club Rep Power: 22	arent both systems developing thier own intake, to fit the SC system, Im sure piping is different now. And he said a CBE is fine. __________________ 2010 LS3 C6 Silver coupe corvette

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stillen Supercharger estimates???	NewYorkJon34	Forced Induction	454	01-23-2010 12:05 AM
Southern "Winter" preparation?	Matt	South East Region	1	11-27-2009 06:23 PM
Titan supercharger	madmocasin	Forced Induction	41	11-09-2009 02:23 AM
Will Stillen Supercharger & G3 intakes Connect?	NewYorkJon34	Forced Induction	23	10-31-2009 01:09 AM

03-11-2010, 06:40 AM	#1040 (permalink)
G35s-Q8 Base Member Join Date: Mar 2010 Location: Kuwait Posts: 20 Drives: 08 G35 Sedan Rep Power: 15	So, i have some questions here for Kyle&Josh@Stillen, are you going to send out the S/C kits with uni-chip or control box just like you did the the old 350z S/C? Or are you planning to use Osiris UpRev reflash and tune? Do you thing the UpRev is better than uni-chip for tuning? And what made you go with that route for the tuning? (uni-chip vs uprev tuning).

03-11-2010, 09:19 AM	#1041 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1119	^ You're gonna have to wait for the release like all of us. It should be coming soon.

03-11-2010, 12:45 PM	#1050 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1119	Oops, thats right, was trying to help quick before I had to run out and was thinking turbo instead of sc. My bad.