Stillen Supercharger boost

NoAiMiSe1 · 08-23-2017, 05:14 AM

Good day Forums,
-
I've been reading this forum to upgrade my SC and solve almost all my problems, so thank you guys for that.

Today i am facing a problem that is unusual and would like the support from you guys.

What i have is a base 370 with a Stillen SC kit, since i installed the kit i got a boost of max 7 psi, then i made all the following upgrade:

- NISMO exhaust system
- FI test pipe
- SC upgrade with Vortech
- 9 lbs pulley upgrade from Stillen (got 1 size smaller belt)
- QRJ 38 mm blow-off valve
- GTR spark plugs
- 1000 CC injectors

yet with all those changes, i am still getting only 7 psi max!! at this point this is killing me and doesn't make any sense . I also tried taking out the blow-off valve and make a run by blocking the hose, got the same boost!

i really would like your feedback on this and hope i can fix this problem.

imazman · 08-23-2017, 08:11 AM

I would get a boost/vaccuum leak test done. I ha two small leaks, one at a throttle body and one at the small hose at front of SC boot. They were very small and weren't the cause of my issues...but definitely hav it done.

Chuck33079 · 08-23-2017, 08:26 AM

The way that kit is set up, you'll lose a couple of psi with test pipes. It's pretty common.

overtureZ · 08-23-2017, 09:37 AM

Do you get a nice vent to atmosphere sound with that BOV?

As for your issue I would say get with TBatt and his no-slip setup, sounds like a slip issue

TopgunZ · 08-23-2017, 10:00 AM

Are you going with the Si trim and the 9psi pulley on the water setup? We all know the outcome of that combination...

TBatt · 08-23-2017, 10:53 AM

Check your belt tensioner. It should look like this. If not, you may have a belt slip issue that I can help you with. I've been selling a lot of kits that will fix belt slip.

Don't rule out a leak though. You can do the leak check pretty easy if you have a compressor and a good regulator. That is how I found mine.

Jayhovah · 08-23-2017, 11:01 AM

Quote:

Originally Posted by TopgunZ

Are you going with the Si trim and the 9psi pulley on the water setup? We all know the outcome of that combination...

It's like a broken Queen record that's stuck on the chorus of "Another One Bites The Dust"...

As an aside, it's sad and disturbing how many motors a setup like that has killed, considering how robust this platform really is.

TopgunZ · 08-23-2017, 11:46 AM

Yes, this platform can take a beating. Strong pistons and rods. But when it is advancing timing with insane heat coming in it doesnt take long for pre-det to take it out.

If only there was a way to get the charge temps down and let the engine know what temp the air is coming in....lol..

NoAiMiSe1 · 08-23-2017, 11:49 AM

Quote:

Originally Posted by imazman

I would get a boost/vaccuum leak test done. I ha two small leaks, one at a throttle body and one at the small hose at front of SC boot. They were very small and weren't the cause of my issues...but definitely hav it done.

i will check if they do a vacuum leak test here, i live in Saudi Arabia, so i am not sure if that is even possible here.

Quote:

Originally Posted by Chuck33079

The way that kit is set up, you'll lose a couple of psi with test pipes. It's pretty common.

True, but when i first installed the kit i didn't have test pipe and it was at 7 psi max also. it feels like thats the maximum pressure that it can reach

Quote:

Originally Posted by overtureZ

Do you get a nice vent to atmosphere sound with that BOV?

As for your issue I would say get with TBatt and his no-slip setup, sounds like a slip issue

well, i dont get a vent sound from the BOV, nothing from the originial BOV that came with the kit or with QRJ. i dont get a sound at all, its like the valve is not releasing anything.

Quote:

Originally Posted by TopgunZ

Are you going with the Si trim and the 9psi pulley on the water setup? We all know the outcome of that combination...

would you share the outcome of that? i am using a SI Trim with 9 psi pulley on a water setup.

Quote:

Originally Posted by TBatt

Check your belt tensioner. It should look like this. If not, you may have a belt slip issue that I can help you with. I've been selling a lot of kits that will fix belt slip.

Don't rule out a leak though. You can do the leak check pretty easy if you have a compressor and a good regulator. That is how I found mine.

please share a link of a belt that you recommend and i will ask the mechanic to have look at it. also, would you have by any chance a link explaining how to do leak test?

Quote:

Originally Posted by Jayhovah

It's like a broken Queen record that's stuck on the chorus of "Another One Bites The Dust"...

As an aside, it's sad and disturbing how many motors a setup like that has killed, considering how robust this platform really is.

you just made me google "Another One Bites The Dust" !!

whats wrong with this setup?

Jayhovah · 08-23-2017, 11:50 AM

Quote:

Originally Posted by TopgunZ

Yes, this platform can take a beating. Strong pistons and rods. But when it is advancing timing with insane heat coming in it doesnt take long for pre-det to take it out.

If only there was a way to get the charge temps down and let the engine know what temp the air is coming in....lol..

We can only dream.

Jayhovah · 08-23-2017, 11:57 AM

Quote:

Originally Posted by NoAiMiSe1

whats wrong with this setup?

The #1 thing that's wrong with this setup is that the air cooler is AFTER that MAF sensors, which the ECU uses to get intake temperature and hence gets completely inaccurate data. This is very dangerous.

The #2 thing is the water cooler is just not adequate for prolonged use. Also dangerous, particularly when your ECU has no idea it has heatsoaked.

Topz is the resident expert on this and offers an Air-to-Air conversion kit which solves all the problems. ALOT safer, and ALOT more power....and pretty inexpensive to boot. No downsides. No brainer.

I am sure others will chime in with more detailed info.

Chuck33079 · 08-23-2017, 12:01 PM

Quote:

Originally Posted by NoAiMiSe1

True, but when i first installed the kit i didn't have test pipe and it was at 7 psi max also. it feels like thats the maximum pressure that it can reach

That's not the maximum pressure it can reach. You were at 7psi with the restriction of the stock cats. You added the parts to run higher boost, but then removed the cats for test pipes. 7+2-2=7

Boost is not flow. Boost is pressure. Removing restrictions will lower boost, but increase flow. Did you dyno the car before/after the switch to test pipes? What you lost in boost may not lead to a 1:1 loss in power, especially with the increase in VE from the engine not straining to push air through the cats. .

TopgunZ · 08-23-2017, 02:58 PM

With an aggressive setup like you have your intake temps are going to be very hot. Too hot for the water setup stillen provides. That is why they only sell the small pulley and the SC trim that came on the supercharger. Otherwise, why wouldnt they want to market a kit that makes much more horsepower. They know the water design (needed for carb approval) is only safe when boosting to a certain limit for longevity to the motor. And that limit is what they sell with the kit. It is not designed to add smaller pulleys and add larger trim supercharger components.

It is not a matter of if your motor will blow, its when. And being in a hot desert climate im sure it will happen sooner than later. Depending on your driver habits, it may take months or.... 1 day at the track.

NoAiMiSe1 · 08-27-2017, 04:53 PM

Quote:

Originally Posted by TBatt

Check your belt tensioner. It should look like this. If not, you may have a belt slip issue that I can help you with. I've been selling a lot of kits that will fix belt slip.

Don't rule out a leak though. You can do the leak check pretty easy if you have a compressor and a good regulator. That is how I found mine.

and we have a winner!!
it looks like its the belt tensioner after all, we replaced it and managed to get 8-9 psi. at this point i am thinking of buying a one size smaller belt to better adjust this problem or go with the kit your talking about

belt tensioner picture
https://goo.gl/photos/pAaDczsDAsTuDfeg9

can you share with me the link for that kit so i can review it and share it with my guy.

also, would someone please share a link for the air-to-air kit, i also would like to review the setup to better manage my car.

i really appreciate all the support for you guys.

TopgunZ · 08-28-2017, 09:58 AM

Right now it is the thread directly above this one. Sounds like you will need to read the entire thing. Pull out the wall charger.

Topgunz - air to air upgrade

08-23-2017, 05:14 AM	#1 (permalink)
NoAiMiSe1 Base Member Join Date: May 2016 Location: bahrain Posts: 7 Drives: car Rep Power: 9	Stillen Supercharger boost Good day Forums, - I've been reading this forum to upgrade my SC and solve almost all my problems, so thank you guys for that. Today i am facing a problem that is unusual and would like the support from you guys. What i have is a base 370 with a Stillen SC kit, since i installed the kit i got a boost of max 7 psi, then i made all the following upgrade: - NISMO exhaust system - FI test pipe - SC upgrade with Vortech - 9 lbs pulley upgrade from Stillen (got 1 size smaller belt) - QRJ 38 mm blow-off valve - GTR spark plugs - 1000 CC injectors yet with all those changes, i am still getting only 7 psi max!! at this point this is killing me and doesn't make any sense . I also tried taking out the blow-off valve and make a run by blocking the hose, got the same boost! i really would like your feedback on this and hope i can fix this problem. Last edited by NoAiMiSe1; 09-29-2019 at 12:50 PM.

08-23-2017, 08:26 AM	#3 (permalink)
Chuck33079 A True Z Fanatic Join Date: Nov 2011 Location: Houston Posts: 12,265 Drives: 2011 370ztt Rep Power: 29539	The way that kit is set up, you'll lose a couple of psi with test pipes. It's pretty common. Jayhovah and Wilson2608 like this. __________________ 2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

08-23-2017, 09:37 AM	#4 (permalink)
overtureZ Enthusiast Member Join Date: Dec 2015 Location: Middle TN Age: 31 Posts: 319 Drives: Da Boosted Z Rep Power: 9	Do you get a nice vent to atmosphere sound with that BOV? As for your issue I would say get with TBatt and his no-slip setup, sounds like a slip issue turtle64b likes this. __________________ Auto/Z Enthusiast - Mechanical Engineer - Fabricator - Do it for dale

08-23-2017, 10:00 AM	#5 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Are you going with the Si trim and the 9psi pulley on the water setup? We all know the outcome of that combination... Chuck33079, TBatt, Jayhovah and 2 others like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-23-2017, 11:46 AM	#8 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Yes, this platform can take a beating. Strong pistons and rods. But when it is advancing timing with insane heat coming in it doesnt take long for pre-det to take it out. If only there was a way to get the charge temps down and let the engine know what temp the air is coming in....lol.. TBatt, Jayhovah, MoulaZ and 2 others like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-23-2017, 08:11 AM	#2 (permalink)
imazman Base Member Join Date: Jan 2014 Location: PA Posts: 120 Drives: 11' 370Z Nismo Rep Power: 11	I would get a boost/vaccuum leak test done. I ha two small leaks, one at a throttle body and one at the small hose at front of SC boot. They were very small and weren't the cause of my issues...but definitely hav it done.

08-23-2017, 02:58 PM	#13 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	With an aggressive setup like you have your intake temps are going to be very hot. Too hot for the water setup stillen provides. That is why they only sell the small pulley and the SC trim that came on the supercharger. Otherwise, why wouldnt they want to market a kit that makes much more horsepower. They know the water design (needed for carb approval) is only safe when boosting to a certain limit for longevity to the motor. And that limit is what they sell with the kit. It is not designed to add smaller pulleys and add larger trim supercharger components. It is not a matter of if your motor will blow, its when. And being in a hot desert climate im sure it will happen sooner than later. Depending on your driver habits, it may take months or.... 1 day at the track. Chuck33079 and wideglideleon like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-28-2017, 09:58 AM	#15 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Right now it is the thread directly above this one. Sounds like you will need to read the entire thing. Pull out the wall charger. Topgunz - air to air upgrade Chuck33079, Jayhovah, wideglideleon and 1 others like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Upgraded Stillen supercharger kit (black) w/ frozen boost	rasheedb	Parts for sale (Private Classifieds)	12	05-07-2016 05:41 PM
[FOR SALE] Stillen supercharger w/ frozen boost	KingZ	Parts for sale (Private Classifieds)	27	04-02-2016 03:14 AM
[FOR SALE] Froozen boost intercooler For stillen supercharger	EVOHUNTER	Parts for sale (Private Classifieds)	2	11-06-2015 11:42 AM
More boost Stillen SuperCharger kit	teknoprep	Engine & Drivetrain	29	05-21-2015 02:20 AM
Stillen Supercharger Froozen Boost Intercooler Install	EVOHUNTER	DIY Section (Do-It-Yourself)	0	05-16-2015 12:01 PM