TAKING ORDERS for winter 2017 turbo kits

James10694 · 10-04-2017, 01:07 AM

After speaking with sasha we came to the conclusion that I more than likely have the right turbo. However the down pipe flange could have potentially warped during welding. I plan on bringing the downpipe to a shop to have the flange grinded down a bit so that it can fit into the compressor housing.

James10694 · 10-04-2017, 07:34 PM

If any of y'all decide to upgrade your radiators or do a coolant change during your install... Don't forget to tighten all the fittings going to the turbo and heater core lines.... Or you'll have a nice mess to clean up

James10694 · 10-05-2017, 02:19 AM

Finally got that b!tch in there. I ended up borrowing a buddy's angle grinder and just went at it. It took my a few times of going back and forth between the turbo and the grinder. In the end I didn't even get the down pipe to push into the turbo all the way. I used the v band clamp to pull the 2 together.

MoulaZ · 10-05-2017, 04:42 AM

Glad to hear it, and gorgeous photo. Also helps me with my RHD ambitions.

Any chance you could take a few more shots of the Air Filter and where it sits in relation to the steering rack? Would be IMMENSELY helpful!

*edit* Attached a photo of mine from way back. Trying to figure out of it'll clear that knuckle without any adjustments */edit*

solidus · 10-05-2017, 08:25 AM

Quote:

Originally Posted by MoulaZ

Glad to hear it, and gorgeous photo. Also helps me with my RHD ambitions.

Any chance you could take a few more shots of the Air Filter and where it sits in relation to the steering rack? Would be IMMENSELY helpful!

*edit* Attached a photo of mine from way back. Trying to figure out of it'll clear that knuckle without any adjustments */edit*

The knuckle in your pic would definitely obstruct the filter. The solution would be running intake tubing up into the fender or forward into the crowded Bay. I racked my brain after the second filter purchase due to melting. We'll all benefit if you figured that one out. Take pics when you do.

Sent from my SAMSUNG-SM-G890A using Tapatalk

Elmo370z · 10-05-2017, 11:41 AM

Quote:

Originally Posted by Boosted Performance

Jwick, it is not that. For whatever reason a one customer was sent the wrong turbine housing. The down pipe now has a 1/4" lip (3" diameter pipe) past the V-band on the turbine side. This allows for a tongue and groove connection, eliminates the need for RTV, and does not mess with the wideband sensor readings...a much better seal.

So the housing that was sent with that turbo did not have the 3.05" inside diameter outlet flange to allow for the the protruding piece to go in to.

Someone said you are stopping production and focusing on supercharger kits, is this true? I need a snail in my life.

Senna-F1 · 10-05-2017, 12:02 PM

Quote:

Originally Posted by Elmo370z

Someone said you are stopping production and focusing on supercharger kits, is this true? I need a snail in my life.

Yes, someone said he was stopping production, but they did not say he was doing SC kits. He was referring to the RJM SC, and was now interested to see where it went.

Elmo370z · 10-05-2017, 12:50 PM

[QUOTE=Senna-F1;3698181]Yes, someone said he was stopping production, but they did not say he was doing SC kits. He was referring to the RJM SC, and was now interested to see where it went.[/QUOT

Stopping production in nomore will be made? or one last batch and done? SASHA!!!!!!!!!!!!! i want a kit damnit lol. I have cash in hand

Senna-F1 · 10-05-2017, 12:54 PM

[QUOTE=Elmo370z;3698189]

Quote:

Originally Posted by Senna-F1

Yes, someone said he was stopping production, but they did not say he was doing SC kits. He was referring to the RJM SC, and was now interested to see where it went.[/QUOT

Stopping production in nomore will be made? or one last batch and done?

Sasha never said he was stopping. Only that one user did, and Ive never seen anyone else say it. So, for now, I'd wait to hear from Sasha. As you know, last word form Sasha was about 6 kits by end of Sept, which has come and gone w/o taking any orders, so let's just wait to see what Sasha himself says.

Elmo370z · 10-05-2017, 01:14 PM

[QUOTE=Senna-F1;3698190]

Quote:

Originally Posted by Elmo370z

Sasha never said he was stopping. Only that one user did, and Ive never seen anyone else say it. So, for now, I'd wait to hear from Sasha. As you know, last word form Sasha was about 6 kits by end of Sept, which has come and gone w/o taking any orders, so let's just wait to see what Sasha himself says.

I hate those 6 people,

. I been checking this damn thread everyday to put my order in.

Senna-F1 · 10-05-2017, 01:16 PM

[QUOTE=Elmo370z;3698199]

Quote:

Originally Posted by Senna-F1

I hate those 6 people,

. I been checking this damn thread everyday to put my order in.

Im pretty sure he didn't take any orders. He said he'd let people know, and he hasn't done that yet.

Boosted Performance · 10-05-2017, 02:22 PM

Gentlemen....I AM NOT STOPPING THE PRODUCTION OF VHR KITS!

The DE and HR kits, yes, but NOT VHR (370z kits).

Come January I will have 30 kits ready to go...in the mean time i will be taking a few orders in the next couple of weeks. I have focused a bit more on getting the DE/HR inventory out the door...hence the delay on the VHR kits. I am not comfortable taking a deposit and then have you guys wait 4 months for product delivery.

I think I have replied to all the PM's as well. If not, please resend.

Boosted Performance · 10-05-2017, 03:04 PM

Quote:

Originally Posted by solidus

The knuckle in your pic would definitely obstruct the filter. The solution would be running intake tubing up into the fender or forward into the crowded Bay. I racked my brain after the second filter purchase due to melting. We'll all benefit if you figured that one out. Take pics when you do.

Sent from my SAMSUNG-SM-G890A using Tapatalk

I have ordered a VHR passenger side manifold, and will be working on a heat shield.

James10694 · 10-05-2017, 04:09 PM

Looking for someone to chime in on this potential issue. One of my IC pipes is contacting the steering knuckle. Is this something I definitely need to adjust?

Elmo370z · 10-05-2017, 04:20 PM

Quote:

Originally Posted by Boosted Performance

Gentlemen....I AM NOT STOPPING THE PRODUCTION OF VHR KITS!

The DE and HR kits, yes, but NOT VHR (370z kits).

Come January I will have 30 kits ready to go...in the mean time i will be taking a few orders in the next couple of weeks. I have focused a bit more on getting the DE/HR inventory out the door...hence the delay on the VHR kits. I am not comfortable taking a deposit and then have you guys wait 4 months for product delivery.

I think I have replied to all the PM's as well. If not, please resend.

Whew

10-04-2017, 01:07 AM	#361 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 916 Drives: 2010 370z Nismo Rep Power: 13	After speaking with sasha we came to the conclusion that I more than likely have the right turbo. However the down pipe flange could have potentially warped during welding. I plan on bringing the downpipe to a shop to have the flange grinded down a bit so that it can fit into the compressor housing. Hotrodz likes this. __________________ Boosted Performance Single Turbo 618whp/489 tq

10-04-2017, 07:34 PM	#362 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 916 Drives: 2010 370z Nismo Rep Power: 13	If any of y'all decide to upgrade your radiators or do a coolant change during your install... Don't forget to tighten all the fittings going to the turbo and heater core lines.... Or you'll have a nice mess to clean up __________________ Boosted Performance Single Turbo 618whp/489 tq

10-05-2017, 02:19 AM	#363 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 916 Drives: 2010 370z Nismo Rep Power: 13	Finally got that b!tch in there. I ended up borrowing a buddy's angle grinder and just went at it. It took my a few times of going back and forth between the turbo and the grinder. In the end I didn't even get the down pipe to push into the turbo all the way. I used the v band clamp to pull the 2 together. GaleForce, Hotrodz, Elmo370z and 2 others like this. __________________ Boosted Performance Single Turbo 618whp/489 tq

10-05-2017, 12:50 PM	#368 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	[QUOTE=Senna-F1;3698181]Yes, someone said he was stopping production, but they did not say he was doing SC kits. He was referring to the RJM SC, and was now interested to see where it went.[/QUOT Stopping production in nomore will be made? or one last batch and done? SASHA!!!!!!!!!!!!! i want a kit damnit lol. I have cash in hand Last edited by Elmo370z; 10-05-2017 at 12:55 PM.

10-05-2017, 02:22 PM	#372 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3382	Gentlemen....I AM NOT STOPPING THE PRODUCTION OF VHR KITS! The DE and HR kits, yes, but NOT VHR (370z kits). Come January I will have 30 kits ready to go...in the mean time i will be taking a few orders in the next couple of weeks. I have focused a bit more on getting the DE/HR inventory out the door...hence the delay on the VHR kits. I am not comfortable taking a deposit and then have you guys wait 4 months for product delivery. I think I have replied to all the PM's as well. If not, please resend. scratchdvinyl, GaleForce, Chuck33079 and 6 others like this. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

10-05-2017, 04:09 PM	#374 (permalink)
James10694 Track Member Join Date: Oct 2013 Location: Las Vegas NV Posts: 916 Drives: 2010 370z Nismo Rep Power: 13	Looking for someone to chime in on this potential issue. One of my IC pipes is contacting the steering knuckle. Is this something I definitely need to adjust? __________________ Boosted Performance Single Turbo 618whp/489 tq

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GReddy 20G 'Tuner' Twin Turbo Kit \| 450+rwhp @ .4Bar \| Now Taking Orders \| FREE S&H!	AJ@ECSMotorsports	Drivetrain/Engine	57	04-09-2013 11:52 AM
Jp vizage 370z polyurathane lip kit. Taking pre orders	LOU@AMPLIFIED	Body Interior/Exterior	22	09-09-2011 02:41 AM
Taking orders for LED/Angel Eyes Headlights.	Tee's Z	Exterior & Interior	17	08-01-2010 11:46 AM
Forged Distributing Taking Orders	Forged DST	Wheels & Tires	51	10-23-2009 09:37 PM
Dealers Not taking anymore custom orders	YamahaR6	Canada	18	05-20-2009 10:31 PM