Nissan 370Z Forum  

Stillen chargecooler tank leaking

I think the cap is leaking on my stillen chargecooler tank Is this a common issue , is there a better cap available It says that its rated to 16

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Engine & Drivetrain > Forced Induction


Reply
 
LinkBack Thread Tools Display Modes
Old 04-03-2016, 01:26 PM   #1 (permalink)
Base Member
 
Join Date: Dec 2013
Location: Uk
Posts: 94
Drives: 2012 370z GT a/t
Rep Power: 12
Maddog is on a distinguished road
Default Stillen chargecooler tank leaking

I think the cap is leaking on my stillen chargecooler tank

Is this a common issue , is there a better cap available

It says that its rated to 16 psi on the cap which would make it capable of holding the coolant in the tank at over 100 degrees c , does the coolant get anything like that temperature?

If not does the system even need a vented cap ? Could I just get an alloy tank made up and use that instead ?

__________________
Eibach sway bars and 25mm spacers, Stillen kit , Level 10 trans, Quaife diff
Maddog is offline   Reply With Quote
Old 04-04-2016, 09:27 AM   #2 (permalink)
Base Member
 
blobbish's Avatar
 
Join Date: Feb 2014
Location: UK
Posts: 58
Drives: 370z Black Edition
Rep Power: 15
blobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond reputeblobbish has a reputation beyond repute
Default

I have a temp gauge in my tank (as you know) and after a hard drive and it sitting soaking heat for an hour I don't see the reservoir get anywhere near 40*C nevermind 100*C. Cant comment on pressure though.

I recall that your kit is running the stillen cooler, but I don't think that can make that much difference.
blobbish is offline   Reply With Quote
Old 04-04-2016, 09:45 AM   #3 (permalink)
Track Member
 
B&W_Evader's Avatar
 
Join Date: Aug 2011
Location: CA
Posts: 972
Drives: slower than before
Rep Power: 387
B&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond reputeB&W_Evader has a reputation beyond repute
Default

I don't think making it a closed system is a good thing. I wonder what the temp (and then pressure) could go up to if you have a pump failure.
__________________
|RIP|6spd-sport|OSG-LSD|XP8|RBF600|Eibach Sways|RE-71R|FI-34Row|Gen3-CAI|Yaw P.S.|
B&W_Evader is offline   Reply With Quote
Old 04-04-2016, 12:05 PM   #4 (permalink)
A True Z Fanatic
 
ANMVQ's Avatar
 
Join Date: Mar 2011
Location: Framingham MA
Posts: 2,732
Drives: 2014 Q50 AWD
Rep Power: 19
ANMVQ will become famous soon enoughANMVQ will become famous soon enough
Default

The system is not closed, I found out the hard way (water go it) the is a open hole on top of the SC. The right brass allen bolt has a hole in the middle :/ IT's open 100 % of the time.
__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,
ANMVQ is offline   Reply With Quote
Old 04-04-2016, 02:57 PM   #5 (permalink)
Base Member
 
Join Date: Dec 2013
Location: Uk
Posts: 94
Drives: 2012 370z GT a/t
Rep Power: 12
Maddog is on a distinguished road
Default

I got the opportunity to check Blobbish's car today , his cap is different , was much tighter than mine and the rubber washer looks thicker, also the edge of the top of the tank has a wider shoulder meaning greater surface area for the washer to seal

My car has an early kit around three years old and has done about 30,000 miles , his kit is new

It could be that the cap has been over tightened in the past and the thread is damaged.

I have ordered some nitrile sheet so will fabricate some new thicker washers and see if that helps

__________________
Eibach sway bars and 25mm spacers, Stillen kit , Level 10 trans, Quaife diff
Maddog is offline   Reply With Quote
Old 04-04-2016, 04:24 PM   #6 (permalink)
A True Z Fanatic
 
ANMVQ's Avatar
 
Join Date: Mar 2011
Location: Framingham MA
Posts: 2,732
Drives: 2014 Q50 AWD
Rep Power: 19
ANMVQ will become famous soon enoughANMVQ will become famous soon enough
Default

I would maybe change the whole tank to one that holds more coolant
__________________
14 Q50 AWD, ARK, ECUTEK (SEB), Takda,
ANMVQ is offline   Reply With Quote
Old 04-05-2016, 04:29 AM   #7 (permalink)
Base Member
 
Join Date: Dec 2013
Location: Uk
Posts: 94
Drives: 2012 370z GT a/t
Rep Power: 12
Maddog is on a distinguished road
Default

Any suggestions of one? I may well get one made up out of alloy
__________________
Eibach sway bars and 25mm spacers, Stillen kit , Level 10 trans, Quaife diff
Maddog is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
fuel tank 305 full tank jamesj1996 Nissan 370Z General Discussions 15 09-20-2014 09:33 PM
Zenclosure Box Leaking. Minhtin Audio & Video 6 09-08-2014 11:21 PM
[FOR SALE] OEM parts: radiator hose, coolant tank, windshield washer tank, fuel pump, etc. 98intrigue Parts for sale (Private Classifieds) 19 02-21-2014 02:40 PM
Stillen Fascia and Washer Tank kielbasa16 Exterior & Interior 6 06-04-2013 02:02 PM
Roof leaking megls Nissan 370Z Roadster (Convertible) 9 08-01-2011 08:28 PM


All times are GMT -5. The time now is 03:11 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2