Topgunz - air to air upgrade

TopgunZ · 08-27-2018, 08:08 AM

Remove bumper. Remove intake Y pipe and boot to SC. Loosen the serpentine belt using a 3/8" drive on the auto tensioner. Remove the 8 or so bolts holding the supercharger bracket on to the face of the engine. Pull entire assembly out.

PM me your email and I can send the stillen install manual so you can take a look how it goes on, just reverse it.

skinnywhitepi · 08-27-2018, 08:25 AM

I’ll take a look at it. If I’m stuck I’ll get back to you. Thanks
I also pm’d you. Didn’t know you had replied. Thanks

G3RSTY7 · 08-27-2018, 01:26 PM

Are there any good indicators of belt slip aside from rubber shavings around blower? I have minimal shavings, i don’t see any slip on datalogs through 7300rpm it makes or at least holds boost at 1.3bars but i’m still peaking at 4.5psi. I’m using soapy spray around supercharger and coupler for leaks, and then pressurized smoke test from front of intercooler.
That said, still managed to make a STI sell his car, and i was pretty happy with how well i hung with an R6 and very modded GTR all things considered and i’m not even on e85 tuning yet

TopgunZ · 08-27-2018, 01:29 PM

Quote:

Originally Posted by G3RSTY7

Are there any good indicators of belt slip aside from rubber shavings around blower? I have minimal shavings, i don’t see any slip on datalogs through 7300rpm it makes or at least holds boost at 1.3bars but i’m still peaking at 4.5psi. I’m using soapy spray around supercharger and coupler for leaks, and then pressurized smoke test from front of intercooler.
That said, still managed to make a STI sell his car, and i was pretty happy with how well i hung with an R6 and very modded GTR all things considered and i’m not even on e85 tuning yet

Your only making 4.5psi? Have you taken it to the dyno? What is your whp?

redondoaveb · 08-27-2018, 01:40 PM

According to the rep I talked to at Vortech, if you see any belt dust, you have belt slippage.

G3RSTY7 · 08-27-2018, 02:05 PM

Quote:

Originally Posted by TopgunZ

Your only making 4.5psi? Have you taken it to the dyno? What is your whp?

I haven’t, still etuning with Seb. Belt dust is likely from when I first put it on I wouldn’t be surprised if i cleaned it off i wouldnt see any more. Must be a leak somewhere. Confusing as before I had a new blower shaft put in i was peaking at 5.8psi and that was with belt/pulley walking and slipping it’s way to death.
I guess if i just put marks on the belt and pulley i would in theory know for sure if it was slipping

G3RSTY7 · 08-29-2018, 04:05 PM

Quick question what is the ID of the blue couplers around the intercooler? 2.5”? 3”?
Played around with boost today, couldn’t find an obvious leak. Put an analog pressure gauge on the evap line and it read just above 6psi at about 6k rpms. So thinking that will be about 7psi at redline. I have the stock 8lb pulley (i believe).. and the billet top end impeller. I live at 5,500’ elevation so perhaps 7psi out of my calculated expectation of about 9psi could be within margin of error for altitude? Still want my own leak down coupler to be sure. What are your boost numbers with what pulley?

redondoaveb · 08-29-2018, 04:59 PM

I never ran mine with the stock 8lb pulley but with the 9lb pulley my car made a little over 10psi.Also, that was with the Si trim sc.

TopgunZ · 08-29-2018, 05:57 PM

The only blue coupler you should have is the one off the supercharger. The in/out of the intercooler is 2.5".

skinnywhitepi · 09-03-2018, 11:25 PM

Somebody please tell me if there is another thread for this or if someone knows. I’m installing my A2A kit and just re-installed the plenum and throttle bodies. The coolant hoses for the bodies, does the short hose go between the two 90° metal tubes coming off of them? Thanks

G3RSTY7 · 09-03-2018, 11:37 PM

Can you see or do you need better angle?

skinnywhitepi · 09-04-2018, 04:08 AM

Thank G3RSTY7 but I think I need a different angle. Are the two 90° connections connected with the small short hose between the two bodies. I have a pic of mine but don Know how to load it up

skinnywhitepi · 09-04-2018, 08:32 AM

Hey TopgunZ. Is it possible to send you an email with pics about some of the install of your kit? Thanks

EVOHUNTER · 09-04-2018, 05:41 PM

welp i can say, dont buy the low to mid range impeller.
Hits 9 psi at like 5800 rpm, then it starts sliding off. at first we thought belt slip, but not slipping at all.

only hit 427 whp and 368 ftlbs.

I think this impeller would be suited better on a mustang etc.. after about 6000 rpm, the boost starts tapering off. it feels way faster then before, but i think thats cause its boosting sooner.

milkcow500 · 09-04-2018, 05:44 PM

Crap where'd you get this impeller from? I have a low mid range impeller from SCR that I haven't put in yet.

Quote:

Originally Posted by EVOHUNTER

welp i can say, dont buy the low to mid range impeller.
Hits 9 psi at like 5800 rpm, then it starts sliding off. at first we thought belt slip, but not slipping at all.

only hit 427 whp and 368 ftlbs.

I think this impeller would be suited better on a mustang etc.. after about 6000 rpm, the boost starts tapering off. it feels way faster then before, but i think thats cause its boosting sooner.

Sent from my Pixel 2 XL using Tapatalk

08-27-2018, 08:08 AM	#2476 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Remove bumper. Remove intake Y pipe and boot to SC. Loosen the serpentine belt using a 3/8" drive on the auto tensioner. Remove the 8 or so bolts holding the supercharger bracket on to the face of the engine. Pull entire assembly out. PM me your email and I can send the stillen install manual so you can take a look how it goes on, just reverse it. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-27-2018, 01:26 PM	#2478 (permalink)
G3RSTY7 Base Member Join Date: Aug 2017 Location: Colorado Posts: 103 Drives: Infiniti G37s 6MT Rep Power: 8	Are there any good indicators of belt slip aside from rubber shavings around blower? I have minimal shavings, i don’t see any slip on datalogs through 7300rpm it makes or at least holds boost at 1.3bars but i’m still peaking at 4.5psi. I’m using soapy spray around supercharger and coupler for leaks, and then pressurized smoke test from front of intercooler. That said, still managed to make a STI sell his car, and i was pretty happy with how well i hung with an R6 and very modded GTR all things considered and i’m not even on e85 tuning yet wideglideleon likes this. __________________ 09 G37S RWD 6MT, Topgunz Supercharger, CJM RFS, Walbro 450, 1050x, Nismo 1.5way LSD, Ecutek FF tuned by Seb IG: G3RSTY7 MyG37.com: RickyBobby

08-27-2018, 01:40 PM	#2480 (permalink)
redondoaveb A True Z Fanatic Join Date: Apr 2017 Location: So. Commiefornia Posts: 6,360 Drives: 2014 Nismo Gunmetal Rep Power: 2684374	According to the rep I talked to at Vortech, if you see any belt dust, you have belt slippage. __________________ Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp

08-29-2018, 04:05 PM	#2482 (permalink)
G3RSTY7 Base Member Join Date: Aug 2017 Location: Colorado Posts: 103 Drives: Infiniti G37s 6MT Rep Power: 8	Quick question what is the ID of the blue couplers around the intercooler? 2.5”? 3”? Played around with boost today, couldn’t find an obvious leak. Put an analog pressure gauge on the evap line and it read just above 6psi at about 6k rpms. So thinking that will be about 7psi at redline. I have the stock 8lb pulley (i believe).. and the billet top end impeller. I live at 5,500’ elevation so perhaps 7psi out of my calculated expectation of about 9psi could be within margin of error for altitude? Still want my own leak down coupler to be sure. What are your boost numbers with what pulley? __________________ 09 G37S RWD 6MT, Topgunz Supercharger, CJM RFS, Walbro 450, 1050x, Nismo 1.5way LSD, Ecutek FF tuned by Seb IG: G3RSTY7 MyG37.com: RickyBobby

08-29-2018, 04:59 PM	#2483 (permalink)
redondoaveb A True Z Fanatic Join Date: Apr 2017 Location: So. Commiefornia Posts: 6,360 Drives: 2014 Nismo Gunmetal Rep Power: 2684374	I never ran mine with the stock 8lb pulley but with the 9lb pulley my car made a little over 10psi.Also, that was with the Si trim sc. __________________ Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp

08-27-2018, 08:25 AM	#2477 (permalink)
skinnywhitepi Base Member Join Date: Oct 2013 Location: germany Posts: 13 Drives: 09 Nissan 370Z Rep Power: 12	I’ll take a look at it. If I’m stuck I’ll get back to you. Thanks I also pm’d you. Didn’t know you had replied. Thanks

08-29-2018, 05:57 PM	#2484 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	The only blue coupler you should have is the one off the supercharger. The in/out of the intercooler is 2.5". __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

09-03-2018, 11:25 PM	#2485 (permalink)
skinnywhitepi Base Member Join Date: Oct 2013 Location: germany Posts: 13 Drives: 09 Nissan 370Z Rep Power: 12	Somebody please tell me if there is another thread for this or if someone knows. I’m installing my A2A kit and just re-installed the plenum and throttle bodies. The coolant hoses for the bodies, does the short hose go between the two 90° metal tubes coming off of them? Thanks

09-04-2018, 04:08 AM	#2487 (permalink)
skinnywhitepi Base Member Join Date: Oct 2013 Location: germany Posts: 13 Drives: 09 Nissan 370Z Rep Power: 12	Thank G3RSTY7 but I think I need a different angle. Are the two 90° connections connected with the small short hose between the two bodies. I have a pic of mine but don Know how to load it up

09-04-2018, 08:32 AM	#2488 (permalink)
skinnywhitepi Base Member Join Date: Oct 2013 Location: germany Posts: 13 Drives: 09 Nissan 370Z Rep Power: 12	Hey TopgunZ. Is it possible to send you an email with pics about some of the install of your kit? Thanks

09-04-2018, 05:41 PM	#2489 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 15	welp i can say, dont buy the low to mid range impeller. Hits 9 psi at like 5800 rpm, then it starts sliding off. at first we thought belt slip, but not slipping at all. only hit 427 whp and 368 ftlbs. I think this impeller would be suited better on a mustang etc.. after about 6000 rpm, the boost starts tapering off. it feels way faster then before, but i think thats cause its boosting sooner. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Best upgrade/mod for 200-300$?	louiey370z	Engine & Drivetrain	10	06-10-2015 12:59 AM
Upgrade?	Dzel	Other Vehicles	83	03-08-2014 06:55 PM
Upgrade	Darryl79	New Roadster 370Z Owner	7	08-23-2012 03:21 PM
Big 3 upgrade ???	dbkustomz	Audio & Video	6	06-30-2012 08:00 AM