Topgunz - air to air upgrade

Pauly Z · 08-15-2016, 06:40 PM

Ok, back from Tampa. Parts are all from Napa.
Pulley- 54 mm #36375
Belt- Micro V 6 rib #061093
You will also need a bolt, washers, and a drive belt pulley spacer.

You need to take your time to ensure that the belt is lined up properly on each pulley. TAKE YOUR TIME or else you could cause some damage.

I have not had one issue with this setup and have no belt slip what so ever.

Sent from my SM-N920V using Tapatalk

TopgunZ · 08-15-2016, 08:06 PM

Quote:

Originally Posted by TBatt

So you are saying that if I clock the volute by about 10 degrees it will make up for six inches of length? Go back and look at the J pipe picture I posted. It is 15 inches long from one end to the other and is about six inches too short to work. Changing the clocking may get me an additional inch but not enough to work. I think the J pipe that I have is too short. Please check the dimension of what I should have.

Right now I am focusing on the belt slip issue. Hopefully Pauly Z can get us the parts list we need to add in the idler and longer belt.

10 degrees was just a number is used as a comparison. However, I am saying if you follow the install instructions then it should work. Your clocking is WAY off. Line it up like in the pictures in the work instructions. With the volute aimed straight at the fender like that there is no way for a 45 to geometrically make a 90 degree turn. If the volute is perfectly horizontal, in order for it to go to another object that is below it, it would have to make a 90 degree bend. If the volute is 45 degrees already and you add a 45 degree coupler then it will be able to align with another plane that is below that plane.

I measured my J pipe and it is the exact same length of mine and the other 10 kits that have been installed per instructions and they do not have any problems. Milkcow did have a problem after swapping some things around but he was making 10psi after the shop installed it and i spoke to them on the phone and they never mentioned the coupler kinking once. They did however have the IC brackets on upside down and I have fixed that by marking the direction on the back side of the brackets.

TBatt · 08-15-2016, 08:46 PM

Okay, thanks for the info. Not sure when I will have time to do this but will give it a try the next time I have things apart.

What kind of gap should I have between the volute and frame rail?

TBatt · 08-15-2016, 08:54 PM

Quote:

Originally Posted by Pauly Z

Ok, back from Tampa. Parts are all from Napa.
Pulley- 54 mm #36375
Belt- Micro V 6 rib #061093
You will also need a bolt, washers, and a drive belt pulley spacer.

You need to take your time to ensure that the belt is lined up properly on each pulley. TAKE YOUR TIME or else you could cause some damage.

I have not had one issue with this setup and have no belt slip what so ever.

Sent from my SM-N920V using Tapatalk

Many thanks! The only other pulley I could find was a 50mm but it was way too wide at 1.5 inches where we need 28 mm (1.1 inches). I'll get the pulley from NAPA tomorrow and check out their bolts and such while I'm there.

I have the 8 rib and 6 rib belts on the way. I am trying an experiment to see if I can remove one rib from the 8 rib to make it a 7. If it doesn't work then the 6 will go on.

Question, just how tight does the 8 rib SC belt need to be? Right now mine is very tight. Anyone measured it with a belt tension meter?

TopgunZ · 08-15-2016, 08:57 PM

Basically trim the lip all the way down to the frame, then I'd leave a good 2mm gap in there for motor movement.

Let me find a pic.

Also, the sc shouldn't be too tight. All your slip is in the serp. I could twist mine almost 90.

TopgunZ · 08-15-2016, 09:08 PM

Boom

BOLIO 671 · 08-23-2016, 06:31 AM

Is there anyone that has bought this kit that is able to provide the dimensions and weight of the kit when it was shipped to you? I'm in the process of trying to figure the shipping to where I am at as the shipping costs for this kit only covers the 48 states and I am over seas.

Any info will be greatly appreciated. I reached out to Topz but I guess he's been busy

TopgunZ · 08-23-2016, 12:00 PM

If someone can help Bolio out that would be great. SInce i ship one box directly from Treadstone i do not have a way to measure that. I am away for work until Friday again so i can get you a dimension on the box that i send when i get back.

But, if someone that has recently received a kit they could measure both boxes also.

TopgunZ · 08-23-2016, 03:45 PM

Just so you guys know, there should be a handful of guys putting up dyno numbers later this week and into next week. The results are going to be awesome!

BOLIO 671 · 08-24-2016, 06:44 AM

Quote:

Originally Posted by TopgunZ

If someone can help Bolio out that would be great. SInce i ship one box directly from Treadstone i do not have a way to measure that. I am away for work until Friday again so i can get you a dimension on the box that i send when i get back.

But, if someone that has recently received a kit they could measure both boxes also.

Yes. I just need an the box dimensions and an estimated weight on both boxes to get me a figure for shipping since I am over seas! Any info would be greatly appreciated.

BOLIO 671 · 08-26-2016, 10:12 PM

Topz did the pipes come in? I'm ready to jump on this

nic370 · 08-27-2016, 03:14 AM

Hi from the UK guys
I've been reading threw this and it looks Awsome

Little background on my situation i had a stillen kit on my last 370 and now have it ready to go on my new 370 but think this is a must before I fit the kit again

Topgunz
What sort of wait is there on your kit ?

Is that intercooler fitting behind the stock crash bar or do we throw that in the bin ? (Trash)

And thanks for comming up with This its Awsome

https://m.facebook.com/story.php?sto...46146868748619

Here's my last car it was first on Ecutek here in uk and custom code written around this car before its release

And then I smashed it

Sent from my SM-G920F using Tapatalk

SlyZGuy · 08-27-2016, 07:02 AM

Quote:

Originally Posted by TopgunZ

If someone can help Bolio out that would be great. SInce i ship one box directly from Treadstone i do not have a way to measure that. I am away for work until Friday again so i can get you a dimension on the box that i send when i get back.

But, if someone that has recently received a kit they could measure both boxes also.

Mine is in the shop now getting installed I'll see if they still have the original boxes I can at least try to get dimensions.

I'll have dyno #'s by Monday or Tuesday at the latest as well...

TopgunZ · 08-27-2016, 11:31 AM

Pipes are about a week behind schedule. They should be done end of this coming week.

The box I ship is 26x10x10 and weighs around 12 lbs.

If I had to guess on the intercooler box I'd say 8x20x30 and around 20lbs.

Optimiser · 08-28-2016, 10:36 PM

Are the intercooler dimensions of 20" X 15.25" X 3.50" for the Air to Air setup just for the core only, or do they include the tanks top and bottom? I can't quite tell from the pics.
Thanks.

08-15-2016, 06:40 PM	#991 (permalink)
Pauly Z Base Member Join Date: Apr 2014 Location: Sylvester, Ga. Posts: 197 Drives: '10 370Z 7AT Rep Power: 11	Ok, back from Tampa. Parts are all from Napa. Pulley- 54 mm #36375 Belt- Micro V 6 rib #061093 You will also need a bolt, washers, and a drive belt pulley spacer. You need to take your time to ensure that the belt is lined up properly on each pulley. TAKE YOUR TIME or else you could cause some damage. I have not had one issue with this setup and have no belt slip what so ever. Sent from my SM-N920V using Tapatalk __________________ Custom Air to Air Stillen SC Setup, CJM S-1S FRS, ID1000 Injectors, Aeromotive 340 Stealth Pump, Test Pipes, Topspeed Exhaust, Z1 Oil Pan Spacer, Swift Springs, Adjustable Rear Camber Arms, 20 and 25mm Spacers, Custom Gauges, and Ecutek

08-15-2016, 08:46 PM	#993 (permalink)
TBatt Track Member Join Date: Apr 2013 Location: Huntsville, AL Posts: 832 Drives: 2019 GT-R Rep Power: 20168	Okay, thanks for the info. Not sure when I will have time to do this but will give it a try the next time I have things apart. What kind of gap should I have between the volute and frame rail? __________________ RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE!

08-15-2016, 08:57 PM	#995 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Basically trim the lip all the way down to the frame, then I'd leave a good 2mm gap in there for motor movement. Let me find a pic. Also, the sc shouldn't be too tight. All your slip is in the serp. I could twist mine almost 90. Jazz8560 likes this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM Last edited by TopgunZ; 08-15-2016 at 09:00 PM.

08-15-2016, 09:08 PM	#996 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Boom Jazz8560 and StillenZ84 like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-23-2016, 06:31 AM	#997 (permalink)
BOLIO 671 A True Z Fanatic Join Date: Mar 2010 Location: GUAHAN Posts: 1,198 Drives: To & From then Back Rep Power: 3399	Is there anyone that has bought this kit that is able to provide the dimensions and weight of the kit when it was shipped to you? I'm in the process of trying to figure the shipping to where I am at as the shipping costs for this kit only covers the 48 states and I am over seas. Any info will be greatly appreciated. I reached out to Topz but I guess he's been busy __________________ 2013 Nismo Z34 / FI TT #091 / IG: @lilzilla_z34

08-23-2016, 12:00 PM	#998 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	If someone can help Bolio out that would be great. SInce i ship one box directly from Treadstone i do not have a way to measure that. I am away for work until Friday again so i can get you a dimension on the box that i send when i get back. But, if someone that has recently received a kit they could measure both boxes also. BOLIO 671 likes this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-23-2016, 03:45 PM	#999 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Just so you guys know, there should be a handful of guys putting up dyno numbers later this week and into next week. The results are going to be awesome! BOLIO 671, Jazz8560 and 2016 like this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-26-2016, 10:12 PM	#1001 (permalink)
BOLIO 671 A True Z Fanatic Join Date: Mar 2010 Location: GUAHAN Posts: 1,198 Drives: To & From then Back Rep Power: 3399	Topz did the pipes come in? I'm ready to jump on this wideglideleon likes this. __________________ 2013 Nismo Z34 / FI TT #091 / IG: @lilzilla_z34

08-27-2016, 03:14 AM	#1002 (permalink)
nic370 Base Member Join Date: Apr 2015 Location: uk Posts: 187 Drives: 370 Rep Power: 10	Hi from the UK guys I've been reading threw this and it looks Awsome Little background on my situation i had a stillen kit on my last 370 and now have it ready to go on my new 370 but think this is a must before I fit the kit again Topgunz What sort of wait is there on your kit ? Is that intercooler fitting behind the stock crash bar or do we throw that in the bin ? (Trash) And thanks for comming up with This its Awsome https://m.facebook.com/story.php?sto...46146868748619 Here's my last car it was first on Ecutek here in uk and custom code written around this car before its release And then I smashed it Sent from my SM-G920F using Tapatalk Last edited by nic370; 08-27-2016 at 03:18 AM.

08-27-2016, 11:31 AM	#1004 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Pipes are about a week behind schedule. They should be done end of this coming week. The box I ship is 26x10x10 and weighs around 12 lbs. If I had to guess on the intercooler box I'd say 8x20x30 and around 20lbs. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

08-28-2016, 10:36 PM	#1005 (permalink)
Optimiser Enthusiast Member Join Date: Mar 2013 Location: Australia Posts: 455 Drives: 2012 Nissan 370Z MT Rep Power: 20144	Are the intercooler dimensions of 20" X 15.25" X 3.50" for the Air to Air setup just for the core only, or do they include the tanks top and bottom? I can't quite tell from the pics. Thanks.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Best upgrade/mod for 200-300$?	louiey370z	Engine & Drivetrain	10	06-10-2015 12:59 AM
Upgrade?	Dzel	Other Vehicles	83	03-08-2014 06:55 PM
Upgrade	Darryl79	New Roadster 370Z Owner	7	08-23-2012 03:21 PM
Big 3 upgrade ???	dbkustomz	Audio & Video	6	06-30-2012 08:00 AM