Looks good man. Just so people aren't confused, brackets, block off plate and gasket maker come with it too.
|
|
LinkBack | Thread Tools | Display Modes |
08-06-2016, 06:31 PM | #946 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
Looks good man.
Just so people aren't confused, brackets, block off plate and gasket maker come with it too.
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
08-08-2016, 04:37 AM | #947 (permalink) |
A True Z Fanatic
Join Date: Mar 2010
Location: GUAHAN
Posts: 1,198
Drives: To & From then Back
Rep Power: 3399 |
Just to clarify...the pipe with the BPV in the pic by the intercooler only fits a 25mm and u would have to purchase an upgraded pipe on eBay for a 50mm flange in order to run the Tial right?
__________________
2013 Nismo Z34 / FI TT #091 / IG: @lilzilla_z34 |
08-08-2016, 08:35 AM | #948 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
Yes this is correct and you would then need 2 couplers and two 2.5" t bolt clamps. However, if you let me know in advance I will send the couplers and clamps instead of the T-coupler.
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
08-08-2016, 05:16 PM | #949 (permalink) | |
Track Member
Join Date: Apr 2013
Location: Huntsville, AL
Posts: 832
Drives: 2019 GT-R
Rep Power: 20168 |
Quote:
Does anyone know what size idler pulley he used? What about using the SC idler pulley? Its off now because I went to a larger idler because of the smaller SC pulley.
__________________
RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE! |
|
08-08-2016, 05:20 PM | #950 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
Its a 2" pulley. Is the supercharger idler a 2"?
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
08-08-2016, 05:59 PM | #951 (permalink) |
Track Member
Join Date: Apr 2013
Location: Huntsville, AL
Posts: 832
Drives: 2019 GT-R
Rep Power: 20168 |
I think so. I will have to check when I get home. Drove the truck today.
I have sent a message to Gates about the possibility of getting a seven rib belt made. It never hurts to ask.....
__________________
RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE! |
08-08-2016, 07:40 PM | #952 (permalink) |
Base Member
Join Date: May 2015
Location: NYC
Posts: 176
Drives: 11 G37xs
Rep Power: 43 |
Hey guys, is this correct? I installed the tial, but I'm only getting half my psi now. I don't remember the coupler to the sc being crimped so badly.
Sent from my SM-N910V using Tapatalk |
08-09-2016, 04:30 PM | #954 (permalink) |
Enthusiast Member
Join Date: Oct 2014
Location: OKC, OK
Posts: 316
Drives: 2010 370Z 7AT S/C
Rep Power: 18 |
Yeah no way it can be that crimped. Adjust the couplers on the intercooler and BOV and pull the pipes out where they aren't as deep into the couplers but make sure there is at least 3/4-1" of the pipe still inside the coupler where the clamps can get a good grip. That should straighten up that coupler on the volute quite a bit where it isn't crimped like that.
__________________
AtA SC|9 lb pulley|2.85" SC|3.47" Jack|E85|CJM S1-SE|ID1000s|Walboro 485|Zeitronix FF|Stillen CBE|AP Racing|Level 10|F.I. Flex plate|Nismo-S tune|EcuTek RaceRom|Sebz|Speed density|Haltech|3GsCustoms Dual pod a-pillar|Carbon Signal GTR gauges|Fujimura|Built| CP Pistons/Carrillo rods|PortPolishHeads/intakes|928motorsports IG: evanosteenz34 |
08-09-2016, 04:35 PM | #955 (permalink) |
Base Member
Join Date: May 2015
Location: NYC
Posts: 176
Drives: 11 G37xs
Rep Power: 43 |
Thanks guys. I was adjusting it for a good 1-2 hours last night, but no luck. I'm going to try messing with it again tonight/tomorrow. I'm also going to purchase a couple hump hose couplers for the bottom. I'm hoping that'll help me out a bit as well. I'm really trying to avoid swapping out for a 90 degree coupler.
|
08-09-2016, 04:40 PM | #956 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
Did any of the guys that went with the Tial setup run into this issue?
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
08-09-2016, 04:54 PM | #957 (permalink) | |
Base Member
Join Date: Apr 2014
Location: Sylvester, Ga.
Posts: 197
Drives: '10 370Z 7AT
Rep Power: 11 |
Quote:
Sent from my SM-N920V using Tapatalk
__________________
Custom Air to Air Stillen SC Setup, CJM S-1S FRS, ID1000 Injectors, Aeromotive 340 Stealth Pump, Test Pipes, Topspeed Exhaust, Z1 Oil Pan Spacer, Swift Springs, Adjustable Rear Camber Arms, 20 and 25mm Spacers, Custom Gauges, and Ecutek |
|
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Best upgrade/mod for 200-300$? | louiey370z | Engine & Drivetrain | 10 | 06-10-2015 12:59 AM |
Upgrade? | Dzel | Other Vehicles | 83 | 03-08-2014 06:55 PM |
Upgrade | Darryl79 | New Roadster 370Z Owner | 7 | 08-23-2012 03:21 PM |
Big 3 upgrade ??? | dbkustomz | Audio & Video | 6 | 06-30-2012 08:00 AM |