Fitting the A2A kit onto a HR motor with the stillen kit. I assume the charger mounting bracket from stillen would still be the same on both VHR and HR
|
|
LinkBack | Thread Tools | Display Modes |
12-11-2018, 02:10 AM | #2582 (permalink) | |
Track Member
Join Date: Jul 2010
Location: Brisbane, Australia
Posts: 503
Drives: MY11 370z Black
Rep Power: 16 |
Quote:
|
|
12-14-2018, 09:35 AM | #2583 (permalink) |
Base Member
Join Date: Aug 2017
Location: Colorado
Posts: 103
Drives: Infiniti G37s 6MT
Rep Power: 8 |
It did... then the gas smell started coming back. One morning I was driving to work and car shut off. Fuel hose popped off ethanol sensor. Improper clamp (screw type not spring) for expansion/contraction with cold temps is what I blame. But then I had a leak at my fuel pressure gauge as well (kinda a scary one like one drip/second). So I bought a 3/8SAE female quick connect to 6an male for the ethanol sensor, PTFE line to 6an-3/8NPT at fuel gauge. Will use yellow teflon at fitting. That should fully do it, the return fuel line looks to be all PTFE lined
__________________
09 G37S RWD 6MT, Topgunz Supercharger, CJM RFS, Walbro 450, 1050x, Nismo 1.5way LSD, Ecutek FF tuned by Seb IG: G3RSTY7 MyG37.com: RickyBobby Last edited by G3RSTY7; 12-14-2018 at 09:49 AM. |
12-31-2018, 01:37 PM | #2587 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
01-02-2019, 11:38 PM | #2588 (permalink) |
Base Member
Join Date: Sep 2013
Location: pittsburgh
Posts: 106
Drives: '14 Z Sport Tour 6M
Rep Power: 3367 |
OK, what did you all do about the lack of clearance between the straight coolant hose nipple on the front throttle body & the 90* silicon (rear) Y tube connector?? Depending on how I wiggle the Y tube, I have about 1/4" to 3/8" (absolute max) clearance from the end of the nipple to the silicon connector. No way to get a hose on that.
__________________
TopGunZ Rotrex SC / CJM RFS / 1300 / Ecutek / Dynosty / F.I. TP & CBE / Z1 / Swift / SPL / Whiteline / Hotchkis / Michelin SP4 |
01-03-2019, 08:56 AM | #2589 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
I havent heard of this issue. However, those tubes bend like butter and it would not hurt them to move them around.
Also, there is a lot of information out there on deleting the throttle body coolant all together. That is what I did.
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
01-03-2019, 09:06 AM | #2590 (permalink) | |
A True Z Fanatic
Join Date: Dec 2010
Location: Houston
Posts: 14,532
Drives: '10 G37 6MT
Rep Power: 2465056 |
Quote:
Mine are gone too. I was going to mention that and then I saw he lived in PA. We don’t worry about freezing temps in Texas, so no reason to run the coolant thru the TBs. |
|
01-03-2019, 10:08 AM | #2591 (permalink) |
Base Member
Join Date: Sep 2013
Location: pittsburgh
Posts: 106
Drives: '14 Z Sport Tour 6M
Rep Power: 3367 |
Thanks guys. I rarely, if ever, drive the car in freezing temps, so I think I'll go ahead & bypass them. No sense adding any unnecessary heat to the incoming air, anyway!
__________________
TopGunZ Rotrex SC / CJM RFS / 1300 / Ecutek / Dynosty / F.I. TP & CBE / Z1 / Swift / SPL / Whiteline / Hotchkis / Michelin SP4 |
01-03-2019, 02:31 PM | #2592 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
Just make sure you take a look on how to do it or you will have coolant spraying out at a rapid pace.
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
01-03-2019, 03:51 PM | #2593 (permalink) | |
A True Z Fanatic
Join Date: Dec 2010
Location: Houston
Posts: 14,532
Drives: '10 G37 6MT
Rep Power: 2465056 |
Topgunz - air to air upgrade
Quote:
Yup and it’s a pita to get a rubber fitting on the backside between the block and the firewall. Edit - the rubber cap is difficult but the zip tie to hold it on is the real pita. Last edited by jwick; 01-03-2019 at 04:23 PM. |
|
01-04-2019, 10:27 AM | #2594 (permalink) |
Base Member
Join Date: Sep 2013
Location: pittsburgh
Posts: 106
Drives: '14 Z Sport Tour 6M
Rep Power: 3367 |
So I took a slightly different route. I simply used the existing hose (C) from the back of the engine & rotated it from the right side of the engine to the left side & connected it to the return nipple on the hard heater line (E). Alternatively, I was going to plug both nipples, but this has fewer points of potential failure. PLUS - I didn't have to mess w/ getting a clamp on that nipple between the block & the firewall!
__________________
TopGunZ Rotrex SC / CJM RFS / 1300 / Ecutek / Dynosty / F.I. TP & CBE / Z1 / Swift / SPL / Whiteline / Hotchkis / Michelin SP4 |
02-06-2019, 10:44 PM | #2595 (permalink) |
A True Z Fanatic
Join Date: Apr 2017
Location: So. Commiefornia
Posts: 6,360
Drives: 2014 Nismo Gunmetal
Rep Power: 2684374 |
Here are my 4 different power levels with the wastegate and ebc.
Blue- High boost on e85 Red- Low boost on e85 Green- Boost off on e85 Gold- Boost off on 91 octane
__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo 700+whp |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Best upgrade/mod for 200-300$? | louiey370z | Engine & Drivetrain | 10 | 06-10-2015 12:59 AM |
Upgrade? | Dzel | Other Vehicles | 83 | 03-08-2014 06:55 PM |
Upgrade | Darryl79 | New Roadster 370Z Owner | 7 | 08-23-2012 03:21 PM |
Big 3 upgrade ??? | dbkustomz | Audio & Video | 6 | 06-30-2012 08:00 AM |