BP turbo build/advice

hc_416 · 05-03-2017, 11:37 PM

I do have a built lower end from aam, its that the wastegates are not workgin right and i have to figer out why...

solidus · 05-04-2017, 07:10 AM

Well hell you should be good then. I say pull the wastegates, take them apart and make sure they're assembled corretly, put in the 5lb springs and then configure the lines the way I showed you. Then set up your boost controller correctly. You said you plumbed all the lines again but did you use new silicone or reuse the old? If you used the old lines did you carefully check each line for holes. I had a small hole near the passenger side wastegate that caused that wastegate to remain closed. It was tiny but I imagine with 23+ psi it expanded enough to cause a ruckus. You're past the hard stuff this is just where it get's tedius and irritating because now you just want to spool.

jwick · 05-04-2017, 09:24 AM

Unless you only want to run 10lbs, you'll need more than a 5lb spring in the WG. I'd put at least the half bar spring, maybe one step bigger.

hc_416 · 05-04-2017, 10:33 AM

Quote:

Originally Posted by solidus

Well hell you should be good then. I say pull the wastegates, take them apart and make sure they're assembled corretly, put in the 5lb springs and then configure the lines the way I showed you. Then set up your boost controller correctly. You said you plumbed all the lines again but did you use new silicone or reuse the old? If you used the old lines did you carefully check each line for holes. I had a small hole near the passenger side wastegate that caused that wastegate to remain closed. It was tiny but I imagine with 23+ psi it expanded enough to cause a ruckus. You're past the hard stuff this is just where it get's tedius and irritating because now you just want to spool.

I will look again, I did not replace every hose, i think i reused two of them. I will go back and check. I will be taking off the waste gates this weekend, I have some time.

Quote:

Originally Posted by jwick

Unless you only want to run 10lbs, you'll need more than a 5lb spring in the WG. I'd put at least the half bar spring, maybe one step bigger.

I am wondering if I swaped the hose's wrong. That is what I am going to check first. then I will take them apart after. Hey were do i get a BOV spring?

jwick · 05-04-2017, 12:07 PM

No clue where to get a different BOV spring.

I also wouldn't go swapping WG springs without a retune. You want to make sure you are tuned for the boost you'll run. Also have your tuner give you a map setting for just WG pressure and then a map for each of your EBC settings (I.e. If you have a low and high boost setting, you'll need a separate map for both).

Boosted Performance · 05-05-2017, 12:38 AM

PM your ship to address and I'll get a BOV spring shipped over to you.

hc_416 · 05-12-2017, 01:51 PM

THE BOOST CONTROLLER IS BROKEN!!!! I BELIEVE THAT THE SOLENOID IS BROKEN/FROZEN. I hooked up the wastes-gate with no boost controller and it worked fine and only boosted to 7 psi. So Do you guys think I should buy a new solenoid, or try a different brand? My brother said that BC is a troublesome and not worth the problems. Any ideas or suggestions? I am also just waiting for the BOV spring to get that right so next week i'm hoping to be close to the new tune and ready to rock for the summer!!!

Hotrodz · 05-12-2017, 02:04 PM

If you are going to be tuned with EcuTek you don't necessarily need a bc. Some are running without one. I would talk to your tuner.

Sent from my SM-N910P using Tapatalk

jwick · 05-12-2017, 02:23 PM

Quote:

Originally Posted by hc_416

THE BOOST CONTROLLER IS BROKEN!!!! I BELIEVE THAT THE SOLENOID IS BROKEN/FROZEN. I hooked up the wastes-gate with no boost controller and it worked fine and only boosted to 7 psi. So Do you guys think I should buy a new solenoid, or try a different brand? My brother said that BC is a troublesome and not worth the problems. Any ideas or suggestions? I am also just waiting for the BOV spring to get that right so next week i'm hoping to be close to the new tune and ready to rock for the summer!!!

What boost controller is it?

jwick · 05-12-2017, 02:24 PM

Quote:

Originally Posted by Hotrodz

If you are going to be tuned with EcuTek you don't necessarily need a bc. Some are running without one. I would talk to your tuner.

Sent from my SM-N910P using Tapatalk

You'd still have to have some kind of solenoid even if Ecutek is controlling boost. I know Ecutek can do it but I've never seen details on how exactly it works.

Hotrodz · 05-12-2017, 03:02 PM

I agree! I know it has been done and I think Hojin was setup that way. I think Seb has setup a few as well.

Sent from my SM-N910P using Tapatalk

hc_416 · 05-12-2017, 04:57 PM

I have a Greddy profec Oled

jwick · 05-12-2017, 06:39 PM

Quote:

Originally Posted by hc_416

I have a Greddy profec Oled

I went with the old Profec I bought NIB off eBay. Nothing fancy but tried and true. I've never heard anything bad about a Profec. You sure the solenoid is hooked up properly?

solidus · 05-13-2017, 01:38 PM

Quote:

Originally Posted by jwick

I went with the old Profec I bought NIB off eBay. Nothing fancy but tried and true. I've never heard anything bad about a Profec. You sure the solenoid is hooked up properly?

I have the same one he does, pure voodoo to set up.

jwick · 05-13-2017, 02:28 PM

Quote:

Originally Posted by solidus

I have the same one he does, pure voodoo to set up.

Not mine. Other than being in bars, it's just High/Low/Off

05-04-2017, 09:24 AM	#408 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	BP turbo build/advice Unless you only want to run 10lbs, you'll need more than a 5lb spring in the WG. I'd put at least the half bar spring, maybe one step bigger. Chuck33079 and Jayhovah like this. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-04-2017, 12:07 PM	#410 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	No clue where to get a different BOV spring. I also wouldn't go swapping WG springs without a retune. You want to make sure you are tuned for the boost you'll run. Also have your tuner give you a map setting for just WG pressure and then a map for each of your EBC settings (I.e. If you have a low and high boost setting, you'll need a separate map for both). __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-05-2017, 12:38 AM	#411 (permalink)
Boosted Performance The370Z.com Sponsor Join Date: Feb 2010 Location: Edmonton, AB Posts: 1,629 Drives: Z's Rep Power: 3382	PM your ship to address and I'll get a BOV spring shipped over to you. __________________ 750WHP starting @ $7,500 to the door FOR DETAILS VISIT: http://www.the370z.com/members/boosted-performance.html FB: https://www.facebook.com/Boosted-Per...6303179791462/ IG @boostedperformanceyeg

05-12-2017, 02:04 PM	#413 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	If you are going to be tuned with EcuTek you don't necessarily need a bc. Some are running without one. I would talk to your tuner. Sent from my SM-N910P using Tapatalk __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

05-12-2017, 03:02 PM	#416 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	I agree! I know it has been done and I think Hojin was setup that way. I think Seb has setup a few as well. Sent from my SM-N910P using Tapatalk jwick likes this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

05-03-2017, 11:37 PM	#406 (permalink)
hc_416 Enthusiast Member Join Date: Aug 2013 Location: CT Posts: 254 Drives: g37 Rep Power: 12	I do have a built lower end from aam, its that the wastegates are not workgin right and i have to figer out why...

05-04-2017, 07:10 AM	#407 (permalink)
solidus Track Member Join Date: Oct 2014 Location: Orlando, Florida Posts: 694 Drives: 15' Nismo Black 6MT Rep Power: 10081	Well hell you should be good then. I say pull the wastegates, take them apart and make sure they're assembled corretly, put in the 5lb springs and then configure the lines the way I showed you. Then set up your boost controller correctly. You said you plumbed all the lines again but did you use new silicone or reuse the old? If you used the old lines did you carefully check each line for holes. I had a small hole near the passenger side wastegate that caused that wastegate to remain closed. It was tiny but I imagine with 23+ psi it expanded enough to cause a ruckus. You're past the hard stuff this is just where it get's tedius and irritating because now you just want to spool.

05-12-2017, 01:51 PM	#412 (permalink)
hc_416 Enthusiast Member Join Date: Aug 2013 Location: CT Posts: 254 Drives: g37 Rep Power: 12	THE BOOST CONTROLLER IS BROKEN!!!! I BELIEVE THAT THE SOLENOID IS BROKEN/FROZEN. I hooked up the wastes-gate with no boost controller and it worked fine and only boosted to 7 psi. So Do you guys think I should buy a new solenoid, or try a different brand? My brother said that BC is a troublesome and not worth the problems. Any ideas or suggestions? I am also just waiting for the BOV spring to get that right so next week i'm hoping to be close to the new tune and ready to rock for the summer!!!

05-12-2017, 04:57 PM	#417 (permalink)
hc_416 Enthusiast Member Join Date: Aug 2013 Location: CT Posts: 254 Drives: g37 Rep Power: 12	I have a Greddy profec Oled

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Turbo Build	davidson_z34	Forced Induction	33	11-12-2015 08:45 PM
Need Advice on Bottom End Build	604GZ	Engine & Drivetrain	5	04-07-2015 10:09 AM
Single turbo build	jlask370	Forced Induction	13	10-07-2013 01:41 PM
Need advice on stereo build....	mengel	Audio & Video	7	02-08-2011 09:24 AM