Hey Guys Has anyone experience with the following Pulleys of Vortech? Adjust for the "STILLEN- Kit"? 8-Rib High-Traction Supercharger Pulleys | Vortech Superchargers (See also the attached Image from me
|
|
LinkBack | Thread Tools | Display Modes |
01-14-2016, 12:50 PM | #1 (permalink) |
Track Member
Join Date: Jun 2011
Location: In the Mountains
Posts: 649
Drives: VW UP! 1.0 Ltr
Rep Power: 15 |
8-Rib High-Traction Supercharger Pulleys
Hey Guys
Has anyone experience with the following Pulleys of Vortech? Adjust for the "STILLEN- Kit"? 8-Rib High-Traction Supercharger Pulleys | Vortech Superchargers (See also the attached Image from me ) Thanks a lot for Your reply Ivo
__________________
/// ONE LAST RIDE /// R.I.P. FAIRLADY Z /// |
01-14-2016, 12:52 PM | #2 (permalink) |
Track Member
Join Date: Jun 2011
Location: In the Mountains
Posts: 649
Drives: VW UP! 1.0 Ltr
Rep Power: 15 |
BTW: YES, i'm in contact with Vortech
But they can give me no experience of my request! (Nevertheless, super nice people and very quick response to my request!)
__________________
/// ONE LAST RIDE /// R.I.P. FAIRLADY Z /// Last edited by swiss370Z; 01-14-2016 at 12:55 PM. |
01-14-2016, 01:35 PM | #3 (permalink) |
Track Member
Join Date: Apr 2013
Location: Huntsville, AL
Posts: 832
Drives: 2019 GT-R
Rep Power: 20168 |
Very interesting! Looks like a good alternative to the cog belt.
Thanks for pointing this out!
__________________
RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE! |
01-14-2016, 01:38 PM | #4 (permalink) |
Track Member
Join Date: Jul 2011
Location: Edmonton, Canada
Posts: 681
Drives: BOOSTED3-7-0
Rep Power: 15 |
what do you want to know? ive done a full custom setup.
If you don't want to have a custom tension backet made. put a 3.50" on the jack shaft side. I when 3.12" on jack side and 2.70 on supercharger side.
__________________
|
01-14-2016, 01:42 PM | #5 (permalink) |
Track Member
Join Date: Apr 2013
Location: Huntsville, AL
Posts: 832
Drives: 2019 GT-R
Rep Power: 20168 |
EVOHunter, did you use these 8 rib pulleys for your setup?
__________________
RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE! |
01-14-2016, 02:20 PM | #6 (permalink) |
Track Member
Join Date: Jul 2011
Location: Edmonton, Canada
Posts: 681
Drives: BOOSTED3-7-0
Rep Power: 15 |
Yes 8 Rib 2.70" bought it off the vortech site.
But remember, if you put on a 2.70" on the blower, you need a custom tension bracket to allow more tension, and 3" idler pulley on the tensioner assembly. ive been through this all on a thread ill post it for you! But like I said, the easiest way is put a bigger pulley on the jack shaft side, then you can still use your stock bracket, pulley and belt I find it funny how Vortech says you can go from a 3.20 to a 3.15 and from a 3.20 to a 2.75" with the stock idler pulley and bracket. it does not work! I know 100% .
__________________
Last edited by EVOHUNTER; 01-14-2016 at 02:28 PM. |
01-14-2016, 03:19 PM | #8 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
They are just shot-blasted. So they provide a little better grip then the electro polished
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
01-14-2016, 04:24 PM | #9 (permalink) |
Track Member
Join Date: Apr 2013
Location: Huntsville, AL
Posts: 832
Drives: 2019 GT-R
Rep Power: 20168 |
Cool! Thanks!
I've been following the Jwillis72 saga.......or should I say soap opera. I feel his pain.
__________________
RJM pedal, Hotchkis Sway Bars, FI TDX, FOG Light, Z1 Slotted Drilled rotors, Stillen SC, Quaife ATB, Z1 Oil cooler, AEM Gauge Set, Galeforce gauge mount, Avant Garde M590 Hypersilver w/RE-11, TopgunZ A2A kit., ECUtek tuned by Seb: ROLL TIDE! |
01-15-2016, 12:28 PM | #11 (permalink) |
Track Member
Join Date: Jun 2011
Location: In the Mountains
Posts: 649
Drives: VW UP! 1.0 Ltr
Rep Power: 15 |
I'll order the following items from Vortech:
2A038-347 8-Rib Supercharger Pulley (3.47") jack side and 2A038-300 8-Rib High-Traction Supercharger Pulley (3.00 ") supercharger side I will Report......(in April.....) Thanks for the Info Guys
__________________
/// ONE LAST RIDE /// R.I.P. FAIRLADY Z /// |
01-25-2016, 05:49 PM | #12 (permalink) |
Enthusiast Member
Join Date: Oct 2014
Location: OKC, OK
Posts: 316
Drives: 2010 370Z 7AT S/C
Rep Power: 18 |
I ordered the same pulleys and the original bolts to bolt them in are too short for the new pulleys. Anyone have experience with this and what did you have to do for them to fit right? Another thing I noticed was if you do replace one the other must be replaced also as it sticks out 1/4" further than the other which would make the belt not flush on both pulleys.
__________________
AtA SC|9 lb pulley|2.85" SC|3.47" Jack|E85|CJM S1-SE|ID1000s|Walboro 485|Zeitronix FF|Stillen CBE|AP Racing|Level 10|F.I. Flex plate|Nismo-S tune|EcuTek RaceRom|Sebz|Speed density|Haltech|3GsCustoms Dual pod a-pillar|Carbon Signal GTR gauges|Fujimura|Built| CP Pistons/Carrillo rods|PortPolishHeads/intakes|928motorsports IG: evanosteenz34 |
01-25-2016, 05:53 PM | #13 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
Are you guys really going to throw 12psi at this kit with that w2a?
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
01-25-2016, 06:42 PM | #14 (permalink) |
Enthusiast Member
Join Date: Oct 2014
Location: OKC, OK
Posts: 316
Drives: 2010 370Z 7AT S/C
Rep Power: 18 |
I was planning on switching out the supercharger pulley for the 3" for now which would gain 1/2 to 1 psi over the 9.5 psi I have now. I ordered the 3.47" to change out when I do go ata in the very near future.
The original plan was to put the 3.47" on combined with the stock stillen pulley which would put me between 10-11 psi. We had the stock stillen on and went to put the 3.47" on and ran into the problem stated earlier. Now the plan is to put the 9 lb pulley and 3" supercharger pulley on before my new tune tomorrow.
__________________
AtA SC|9 lb pulley|2.85" SC|3.47" Jack|E85|CJM S1-SE|ID1000s|Walboro 485|Zeitronix FF|Stillen CBE|AP Racing|Level 10|F.I. Flex plate|Nismo-S tune|EcuTek RaceRom|Sebz|Speed density|Haltech|3GsCustoms Dual pod a-pillar|Carbon Signal GTR gauges|Fujimura|Built| CP Pistons/Carrillo rods|PortPolishHeads/intakes|928motorsports IG: evanosteenz34 Last edited by StillenZ84; 01-25-2016 at 07:01 PM. |
01-25-2016, 06:59 PM | #15 (permalink) |
A True Z Fanatic
Join Date: Jun 2012
Location: Minneapolis
Posts: 2,651
Drives: 06 350Z , 09 370Z MT
Rep Power: 6834 |
When are you going to dyno that 3.0"?
__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[WTB] NST Pulleys | chuckie311 | Parts for sale (Private Classifieds) | 1 | 11-13-2014 10:48 PM |
Stillen Performance Intakes, Exhaust, Oil Coolers, Pulleys, & SUPERCHARGER! Intense! | INTENSEPOWER | Exhaust/Intake | 50 | 05-02-2012 02:28 AM |
[FOR SALE] NST Pulleys | B.A.Q | Parts for sale (Private Classifieds) | 17 | 10-04-2011 01:49 AM |
What pulleys? | import111 | Engine & Drivetrain | 1 | 10-03-2010 06:14 PM |
Considering NST Pulleys | Rooskey | Nissan 370Z General Discussions | 4 | 07-23-2010 05:07 AM |