Stage 2 sc build has begun

tiller · 04-16-2016, 09:56 PM

Quote:

Originally Posted by Jinxx

I'm trying to get in a shop Monday for a Dyno run just to see the numbers ... Most shops are booked up and trying to squeeze me in

Cool,let me know some numbers when you get them,very curious

Jinxx · 04-17-2016, 01:28 AM

I'm still on the can tune so I don't expect very good numbers ..... However the pulley change made my data logs look better

tiller · 04-17-2016, 09:05 AM

Ecutek and seb at specialty have been amazing so far man,amazing customer service

Jinxx · 04-18-2016, 01:34 PM

soooo I dynode the car today ...... car was maxing injectors out so I need to upgrade...unless I have room to increase the fuel with the 650cc ... as it was it made 480whp and 350tq @7200 rpms but started leaning out around 6500 rpms and at 7200 was around 12.8 afr.... I don't know how to post a pic or vid yet ill post it when I figure it out

Jinxx · 04-18-2016, 03:32 PM

first dyno run can tune .......the 480whp is a 5th gear pull...the 390whp is a fourth gear pull [ATTACH]

[/ATTACH]

TopgunZ · 04-18-2016, 03:59 PM

90 whp difference in 5th gear?

What max psi did you hit?

Jinxx · 04-18-2016, 05:04 PM

Quote:

Originally Posted by TopgunZ

90 whp difference in 5th gear?

What max psi did you hit?

I didn't get the psi off the 4th gear pull but I got it for the 5th gear .. 12.3 lbs at 7200

tiller · 04-18-2016, 06:53 PM

What kind of dyno is it?you should be able to hit 500whp on 650 injectors on 12lbs of boost,do you think the uprev is holding you back?where's your wideband o2 mounted on pipe

Jinxx · 04-18-2016, 11:32 PM

It's a dynojet .... Not sure if I have any adjustment left in the tune ... I never installed the voltage regulator for the fuel system Seb says at this point voltage regulator won't help and I could verify the fuel pressure .. If it's a pressure drop tunning would help if pressure doesn't drop then I could tune it but recommends me going to return fuel system ..... Not sure how I wanna go about it yet ... Prolly should just do the return kit

tiller · 04-20-2016, 08:39 PM

Quote:

Originally Posted by Jinxx

It's a dynojet .... Not sure if I have any adjustment left in the tune ... I never installed the voltage regulator for the fuel system Seb says at this point voltage regulator won't help and I could verify the fuel pressure .. If it's a pressure drop tunning would help if pressure doesn't drop then I could tune it but recommends me going to return fuel system ..... Not sure how I wanna go about it yet ... Prolly should just do the return kit

I'd call cjm,I've had great dealings with them

Jinxx · 04-20-2016, 10:03 PM

I talked to him today ... I think the return will the best route to take .... Always something .... But still I can't complain too much

tiller · 04-23-2016, 09:59 PM

Quote:

Originally Posted by Jinxx

I talked to him today ... I think the return will the best route to take .... Always something .... But still I can't complain too much

Are you going with ecutek?

Jinxx · 04-23-2016, 10:45 PM

No not going with ecutek ..... I'll hold out for a while for up rev to update

tiller · 04-24-2016, 01:12 PM

We're you able to see where exactly your fueling issues on the dyno were happening?like rpm wise?do you have an FPR gauge on your rail?

Jinxx · 04-24-2016, 03:41 PM

I don't have a fuel pressure gauge ...and I think it would have been fine with the 92mm pulley and prolly a little rich .....but after changing to the 85mm pulley the boost comes on much sooner and running 40-50% more boost ..requiring more fuel ..once I get the return fuel system to be able to increase the fuel pressure as boost increases it should be good...I would think the 92mm would have ran around 450ish whp.....

Stock fuel pressure is 52 ...as boost increases it drops soooo with 8lbs pulley fuel pressure would be 44lbs which would support the boost ...with the 12lbs pulley pressure would be around 40lbs and not enough for the boost .....no real way to increase it without the return system

04-18-2016, 03:59 PM	#141 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	90 whp difference in 5th gear? What max psi did you hit? __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

04-24-2016, 03:41 PM	#150 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	I don't have a fuel pressure gauge ...and I think it would have been fine with the 92mm pulley and prolly a little rich .....but after changing to the 85mm pulley the boost comes on much sooner and running 40-50% more boost ..requiring more fuel ..once I get the return fuel system to be able to increase the fuel pressure as boost increases it should be good...I would think the 92mm would have ran around 450ish whp..... Stock fuel pressure is 52 ...as boost increases it drops soooo with 8lbs pulley fuel pressure would be 44lbs which would support the boost ...with the 12lbs pulley pressure would be around 40lbs and not enough for the boost .....no real way to increase it without the return system Last edited by Jinxx; 04-24-2016 at 03:45 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GTM Stage 1.5 supercharger build	snowsurfdirtx	Forced Induction	197	05-07-2017 07:04 AM
GTM Stage 1.5 Supercharged Roadster Build	JVerge5363	Forced Induction	26	06-13-2014 12:02 PM
FRYZIA23 GTM stage 1.5 S/C build	fryzia23	Forced Induction	91	01-16-2014 12:20 AM
New GTM stage 2 TT build	Billy02987	Forced Induction	212	06-04-2011 04:56 PM
The Specialty-Z GTM Stage 2 Build	Seb@SZ	Forced Induction	62	12-12-2010 11:34 AM

04-17-2016, 01:28 AM	#137 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	I'm still on the can tune so I don't expect very good numbers ..... However the pulley change made my data logs look better

04-17-2016, 09:05 AM	#138 (permalink)
tiller Enthusiast Member Join Date: Feb 2011 Location: ontario Posts: 370 Drives: 09 370z touring Rep Power: 14	Ecutek and seb at specialty have been amazing so far man,amazing customer service

04-18-2016, 01:34 PM	#139 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	soooo I dynode the car today ...... car was maxing injectors out so I need to upgrade...unless I have room to increase the fuel with the 650cc ... as it was it made 480whp and 350tq @7200 rpms but started leaning out around 6500 rpms and at 7200 was around 12.8 afr.... I don't know how to post a pic or vid yet ill post it when I figure it out

04-18-2016, 06:53 PM	#143 (permalink)
tiller Enthusiast Member Join Date: Feb 2011 Location: ontario Posts: 370 Drives: 09 370z touring Rep Power: 14	What kind of dyno is it?you should be able to hit 500whp on 650 injectors on 12lbs of boost,do you think the uprev is holding you back?where's your wideband o2 mounted on pipe

04-18-2016, 11:32 PM	#144 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	It's a dynojet .... Not sure if I have any adjustment left in the tune ... I never installed the voltage regulator for the fuel system Seb says at this point voltage regulator won't help and I could verify the fuel pressure .. If it's a pressure drop tunning would help if pressure doesn't drop then I could tune it but recommends me going to return fuel system ..... Not sure how I wanna go about it yet ... Prolly should just do the return kit

04-20-2016, 10:03 PM	#146 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	I talked to him today ... I think the return will the best route to take .... Always something .... But still I can't complain too much

04-23-2016, 10:45 PM	#148 (permalink)
Jinxx Track Member Join Date: Dec 2015 Location: South Carolina Posts: 699 Drives: 2017 nismo 370z Rep Power: 3375	No not going with ecutek ..... I'll hold out for a while for up rev to update

04-24-2016, 01:12 PM	#149 (permalink)
tiller Enthusiast Member Join Date: Feb 2011 Location: ontario Posts: 370 Drives: 09 370z touring Rep Power: 14	We're you able to see where exactly your fueling issues on the dyno were happening?like rpm wise?do you have an FPR gauge on your rail?