Stillen Air to Air setup

JWillis72 · 08-05-2015, 08:31 PM

Quote:

Originally Posted by EliteXpress

My kit is seeing 10.5psi with the Stillen 9 lb pulley and test pipes.

What whp/tq are you getting?

TopgunZ · 08-05-2015, 09:15 PM

Remember, by going a2a we will realize more pressure drop than the original design. Probably about 1 to 1.5 psi.

Yes im on a built motor.

Pushed my dyno back a week. So im on for the 22nd.

Sunday I built a pool slash hot tub in my driveway. A truck and a shop vac have dual purpose.

luigi90210 · 08-05-2015, 09:24 PM

Quote:

Originally Posted by TopgunZ

Interesting. I have a series of questions though.

Are you going for CARB approval? Why are you recircing your dump back into intake and why are you plumbing into the valve cover?

Is your Y pipe sitting vertical and you are going to have one pipe underneath the other? Looks like that would be a long split.

Why do you have the BPV/BOV after the IC? This is going to pass hot air from the SC through the IC so at a standstill, any light, and such it is going to pre-heat soak your IC, isn't it?

Don't need to go for carb approval. Intercoolers on gas motors are not regulated and can be added, modified, or removed without issues even if the kit is aftermarket, so if you wanted to run an air to air intercooler over the supplied air to water setup its perfectly fine. However you would not technically be able to change the tune but no smog tech/bar tech can see if the tune has been altered so who cares.

Its funny how many things are not carb regulated in California.

Edit oh you would have to recirc the BPV as opposed to letting it vent to atmosphere but if the tech can't see it venting visually, you're fine, the smog techs can not legally tear apart your car just to inspect it, so if its out of sight no sense in worrying about it.

EliteXpress · 08-05-2015, 09:52 PM

Quote:

Originally Posted by JWillis72

What whp/tq are you getting?

426WHP 336TQ

JWillis72 · 08-06-2015, 06:37 AM

Quote:

Originally Posted by EliteXpress

426WHP 336TQ

Did you ever dyno it on the 8lb pulley? I'm getting 418/312 on the stock Stillen set up but I am also at sea level + 10-20.

ANMVQ · 08-06-2015, 10:47 AM

Quote:

Originally Posted by JWillis72

Did you ever dyno it on the 8lb pulley? I'm getting 418/312 on the stock Stillen set up but I am also at sea level + 10-20.

Those sound about right on the stock pulley I was making 412 and 300 WTRQ , stock set up, What PSI are you actually seeing tho, I was seeing 9 PSI.

JWillis72 · 08-06-2015, 10:54 AM

I think it was 8.6-8.7, I have a AFR/ boost gauge but the boost is on the outside dial part so I don't pay a lot of attention to it.

EliteXpress · 08-06-2015, 12:13 PM

Quote:

Originally Posted by JWillis72

Did you ever dyno it on the 8lb pulley? I'm getting 418/312 on the stock Stillen set up but I am also at sea level + 10-20.

Never dyno on the stock pully.

ANMVQ · 08-06-2015, 12:28 PM

Quote:

Originally Posted by EliteXpress

Never dyno on the stock pully.

:/ Whys this ?

EliteXpress · 08-06-2015, 01:40 PM

Quote:

Originally Posted by ANMVQ

:/ Whys this ?

Labor and more dyno time, really was no need to.

ANMVQ · 08-07-2015, 07:23 AM

Quote:

Originally Posted by EliteXpress

Labor and more dyno time, really was no need to.

Ok so you confused me, Why wouldn't you dyno on the stock pulley almost NO one runs their can tune, so you road tuned your car :/

BTW what labor? you drive car on the dyno strap it down and make 3 pulls for 70$

JWillis72 · 08-07-2015, 07:30 AM

He's saying he never tuned it on the 8lb not that you shouldn't tune with the 8 lb if thats what your using.

ANMVQ · 08-07-2015, 07:36 AM

Quote:

Originally Posted by JWillis72

He's saying he never tuned it on the 8lb not that you shouldn't tune with the 8 lb if thats what your using.

Ah thanx man so he was happy with making 40 more WHP? Or was he one of those who made 400 WHP on the "Stillen tune". or just go right to the 9LBS and hold your breath that the motor doesn't pop ? Thanx JWillis72

JWillis72 · 08-07-2015, 08:10 AM

I've seen him and others do the 9lb pulley with no problems. The ones that seem to have problems are on the 9lb and upgraded impeller.

jwick · 08-07-2015, 08:19 AM

Quote:

Originally Posted by JWillis72

I think it was 8.6-8.7, I have a AFR/ boost gauge but the boost is on the outside dial part so I don't pay a lot of attention to it.

Words never said by a turbo guy. One of the benefits to having your boost set by the pulley size

08-07-2015, 07:30 AM	#177 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 45	He's saying he never tuned it on the 8lb not that you shouldn't tune with the 8 lb if thats what your using. ANMVQ and EliteXpress like this.

08-07-2015, 08:10 AM	#179 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 45	I've seen him and others do the 9lb pulley with no problems. The ones that seem to have problems are on the 9lb and upgraded impeller. EliteXpress likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom intake setup -- Stillen G3's, Velocity Stacks, Custom Front Crash Beam, pics	'10Anamoly	Intake/Exhaust	26	02-14-2015 10:59 AM
My new setup :)	Flushnismo	Nissan 370Z Photos / Spyshots / Video / Media Gallery	30	06-29-2012 11:03 AM
[WTB] wtb nismo seats stillen g3 cai stillen headers and stillen exhaust	bloodvayne	Parts for sale (Private Classifieds)	1	12-18-2011 09:25 PM
Stillen Sway bars - 305 rear tires - setup?	FricFrac	Track / Autocross / Drifting / Dragstrip	2	02-15-2011 10:33 AM
Full Stillen Bolt-On Setup - Videos!	RCZ	Intake/Exhaust	114	06-15-2009 04:32 PM

08-06-2015, 10:54 AM	#172 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 45	I think it was 8.6-8.7, I have a AFR/ boost gauge but the boost is on the outside dial part so I don't pay a lot of attention to it.