Stillen Air to Air setup

JWillis72

My plates should be ready tomorrow but my car has a long way to go before tuning.


Sent from my iPhone using Tapatalk

JWillis72

Sent from my iPhone using Tapatalk

TopgunZ

Nice work! So whats your ETA to see the dyno?

__________________
ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

JWillis72

The plan is for the shop to get the supercharger rebuilt and back in with the injectors and GTR plugs and get it to the other shop to weld the piping sometime next week. Hopefully my headers will ship Monday or Tuesday and can go in the week after next. You will probably get to the dyno before me but I hope to not be far behind because I've paid to be at Sebring Oct 3-4.


Sent from my iPhone using Tapatalk

JWillis72

I think I am going to have them kind of follow your intake but in aluminum pipe and the MAFs in 2 3" sections. If that doesn't work we will speed density tune it.


Sent from my iPhone using Tapatalk

roplusbee

Do you mind if I ask why you went with GT-R plugs over the HKS plugs? I went through two sets of GT-R plugs in an abnormally short time (Greddy TT Kit). When I came to terms with my wallet and bought the HKS plugs, I had no more issues. Just curious.......

__________________
2007 350Z NISMO #0618: Zerolift | UPREV | F.I. | Greddy | Competition Clutch | Injector Dynamics | Aeromotive | Pioneer | JL

jwick

Ecutek and a Juke MAP sensor...FTW!

__________________
'10 G37T 6MT Graphite/Graphite - BP - G37T Build

JWillis72

I was recommended them but don't remember by who and the shop does tons of GTRs so I didn't have to order them. My car is behind the white one.

.


Sent from my iPhone using Tapatalk

JWillis72

Why a Juke MAP? We are doing Ecutech.


Sent from my iPhone using Tapatalk

EVOHUNTER

youll need to tap a map sensor into the manifold. Remove the MAF signal wire from both MAfs, Those then have to be wired into the MAP sensor.

After this, Speed density is possible.

__________________

jwick

Just what my tuner suggests. I assume it's the cheaper and easier solution.

I didn't get into all the details cuz still several months away from the Ecutek switch.

__________________
'10 G37T 6MT Graphite/Graphite - BP - G37T Build

StillenZ84

Right. I was told by John Visconti that it requires a 4 BAR Map sensor. Where can you get one? I can't find one anywhere.

__________________
AtA SC|9 lb pulley|2.85" SC|3.47" Jack|E85|CJM S1-SE|ID1000s|Walboro 485|Zeitronix FF|Stillen CBE|AP Racing|Level 10|F.I. Flex plate|Nismo-S tune|EcuTek RaceRom|Sebz|Speed density|Haltech|3GsCustoms Dual pod a-pillar|Carbon Signal GTR gauges|Fujimura|Built| CP Pistons/Carrillo rods|PortPolishHeads/intakes|928motorsports IG: evanosteenz34

JWillis72

I think a 3 BAR bar would work unless you are doing something big. The 4 bar I looked at said they were for 20-43 lb of boost.


Sent from my iPhone using Tapatalk

StillenZ84

Ok cool. Yeah I saw that also. I definitely don't see going that much boost ever.

__________________
AtA SC|9 lb pulley|2.85" SC|3.47" Jack|E85|CJM S1-SE|ID1000s|Walboro 485|Zeitronix FF|Stillen CBE|AP Racing|Level 10|F.I. Flex plate|Nismo-S tune|EcuTek RaceRom|Sebz|Speed density|Haltech|3GsCustoms Dual pod a-pillar|Carbon Signal GTR gauges|Fujimura|Built| CP Pistons/Carrillo rods|PortPolishHeads/intakes|928motorsports IG: evanosteenz34

EVOHUNTER

The easiest way would be to use a 3 bar Gm MAP sensor. This has a 3 wire connecter, one would be ground to the body, 2 would be a 5V source, and 3 would be signal wired into your MAF signal wire. Theres a vacuum port on the sensor, Have a vacuum line from the intake manifold to the sensor. This is where I'm kinda stumped. Do we wire both MAF signal wires into one map sensor? Do we Run 2 map sensors? You could run 2, it wouldn't be hard.

__________________