Switch Panel on console

kenchan · 10-02-2009, 02:01 PM

nevermind, i just ordered a pair of LED strips from amazon.

like $16.

also ordered the pioneer backup camera and foglamp so will do all together. going to relocate the bypass switch to one of the rockers.

so for me:
Rocker1: DVD bypass sw
Rocker2: interior LED (footwell area)
Rocker3: rear foglamp

dcrew1x · 10-02-2009, 04:27 PM

Let me know how your interior LED install goes!

Post a DIY fosho!

M.J. · 10-02-2009, 05:28 PM

Quote:

Originally Posted by kenchan

nevermind, i just ordered a pair of LED strips from amazon.

like $16.

Sorry Ken. I've been working on my wheel/tire package and wasn't following the thread. But I got my LED's from here LED's and I bought these My LED's in straight chrome blue.
I set up my switches pretty much the same way.
1. Sub Amp Bypass
2. Interior Lights
3. Momentary on for something someday maybe

M.J. · 10-02-2009, 05:31 PM

Quote:

Originally Posted by Race

Anyone have any tips on getting the dummy covers out? Can it be done without removing the entire center console? I've scratched up that little area and ruined one butter knife already...

The dummy switch covers go down and out the bottom so you gotta take the cup holder out. The replacement switches will go in from the top.

kenchan · 10-02-2009, 10:34 PM

Quote:

Originally Posted by M.J.

Sorry Ken. I've been working on my wheel/tire package and wasn't following the thread. But I got my LED's from here LED's and I bought these My LED's in straight chrome blue.
I set up my switches pretty much the same way.
1. Sub Amp Bypass
2. Interior Lights
3. Momentary on for something someday maybe

thanks for the info.

guess i'll try them next time around.

speedoflife · 10-02-2009, 11:54 PM

LED's 2
Here is another good website as well. Nice install man! Super clean.

kenchan · 10-03-2009, 09:36 AM

MJ- when you did your LED's did you pull the +12v from the center console's cigarette socket? I was looking through the servicemanual and thought that would be a very easy tap(?).

I can use that for the rear fog too since the bulb is 21w (1.75A).

kenchan · 10-05-2009, 12:19 AM

i realized it's kinda tough to get at that center console 12v so left it as is and removed
the front 12v and converted it into my power source.

i never use that front socket plus people keep kicking it by accident when something's
plugged in so removed it completely. 2 screws and that whole assembly comes off.

regular spade connectors slide right in. very convenient.

kenchan · 10-05-2009, 10:47 AM

here's wat my switch box looks like today... lol

i should have my rockers in by Wed...hopefully. my car is in pieces right now waiting on several items to come in.

M.J. · 10-06-2009, 02:38 AM

Project in progress. Parts all over the place. I know how that goes.

kenchan · 10-06-2009, 12:28 PM

Quote:

Originally Posted by M.J.

Project in progress. Parts all over the place. I know how that goes.

yah, my car is in pieces right now in the garage. got 4 different little projects going at the same time.

so any pictures of your interior light install?

kenchan · 10-07-2009, 01:43 PM

gotz my rocker switches this am.

looks to be high quality.

i also wired up these LED strips last night, just a matter of hooking
up the switches. these come with double stick tape on the back
side so i mounted them under the seats where there is a stainless
bar that runs side to side (and stationary even if you moved the
seats).

will take some shots tonight. put a sharpie in the pict for size reference.

now the only problem i got is removing the damn dummy
rear fog lamp. the bolt spins with the 10mm nut on both.

i think im going to drill into them and bust them off.

theDreamer · 10-07-2009, 01:45 PM

Which bolt? The higher or the lower one?
When putting mine back in the higher one (if under the car the one on the left side) went in and then started spinning near the end.

kenchan · 10-07-2009, 02:17 PM

Quote:

Originally Posted by theDreamer

Which bolt? The higher or the lower one?
When putting mine back in the higher one (if under the car the one on the left side) went in and then started spinning near the end.

both of them. like the DIY, i took my ratchet VERY SLOWLY but the bolt spun from the getgo...

theDreamer · 10-07-2009, 02:19 PM

Quote:

Originally Posted by kenchan

both of them. like the DIY, i took my ratchet VERY SLOWLY but the bolt spun from the getgo...

Sucks to hear, and it is not exactly an easy area to do work in to begin with.

10-02-2009, 04:27 PM	#17 (permalink)
dcrew1x Track Member Join Date: Jun 2009 Location: SoCal Posts: 821 Drives: Graphite Bullet Rep Power: 369	Let me know how your interior LED install goes! Post a DIY fosho! __________________ 2009 PG 6MT Sports Stillen Gen3 CAI \| Stillen CBE \| AMS Short Shifter \| Nismo Brace Kit

10-07-2009, 01:45 PM	#28 (permalink)
theDreamer A True Z Fanatic Join Date: Feb 2009 Location: Texas Posts: 30,879 Drives: 370z Rep Power: 4210	Which bolt? The higher or the lower one? When putting mine back in the higher one (if under the car the one on the left side) went in and then started spinning near the end. __________________ theDreamer's Z // Fast Intentions // Uprev // GTM // HKS // TEIN theDreamer's Silvia // URAS // GREDDY Houston Zs // Facebook // Twitter // Instagram

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to Remove Passenger-side door panel?	kailua	Audio & Video	5	09-10-2014 08:54 PM
Lower Engine Panel Removal Opinions?	CCCLXXZ	Nissan 370Z General Discussions	5	08-25-2009 08:36 PM
Euro Fog Light Switch	Jason	Exterior & Interior	3	06-22-2009 03:26 PM
So You Need a VIN To Order An SRM Switch	CBRich	Nissan 370Z General Discussions	6	06-03-2009 03:10 PM
Messed up my driver side rocker panel.	JonnieN	Nissan 370Z General Discussions	2	05-23-2009 07:29 PM

10-02-2009, 02:01 PM	#16 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	nevermind, i just ordered a pair of LED strips from amazon. like $16. also ordered the pioneer backup camera and foglamp so will do all together. going to relocate the bypass switch to one of the rockers. so for me: Rocker1: DVD bypass sw Rocker2: interior LED (footwell area) Rocker3: rear foglamp

10-02-2009, 11:54 PM	#21 (permalink)
speedoflife Enthusiast Member Join Date: Aug 2009 Location: MS/TX Posts: 268 Drives: '06 Pontiac G.P. Rep Power: 16	LED's 2 Here is another good website as well. Nice install man! Super clean.

10-03-2009, 09:36 AM	#22 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	MJ- when you did your LED's did you pull the +12v from the center console's cigarette socket? I was looking through the servicemanual and thought that would be a very easy tap(?). I can use that for the rear fog too since the bulb is 21w (1.75A).

10-05-2009, 12:19 AM	#23 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	i realized it's kinda tough to get at that center console 12v so left it as is and removed the front 12v and converted it into my power source. i never use that front socket plus people keep kicking it by accident when something's plugged in so removed it completely. 2 screws and that whole assembly comes off. regular spade connectors slide right in. very convenient.

10-05-2009, 10:47 AM	#24 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	here's wat my switch box looks like today... lol i should have my rockers in by Wed...hopefully. my car is in pieces right now waiting on several items to come in.

10-06-2009, 02:38 AM	#25 (permalink)
M.J. Base Member Join Date: Feb 2009 Location: Honolulu, Hawaii Posts: 68 Drives: '09 370 White, 6spd. Rep Power: 16	Project in progress. Parts all over the place. I know how that goes.

10-07-2009, 01:43 PM	#27 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	gotz my rocker switches this am. looks to be high quality. i also wired up these LED strips last night, just a matter of hooking up the switches. these come with double stick tape on the back side so i mounted them under the seats where there is a stainless bar that runs side to side (and stationary even if you moved the seats). will take some shots tonight. put a sharpie in the pict for size reference. now the only problem i got is removing the damn dummy rear fog lamp. the bolt spins with the 10mm nut on both. i think im going to drill into them and bust them off.