Carbon fiber amuse install help needed

Originally Posted by wheee!

That is another thing with the Extreme dimensions kit, it uses the stock under shroud.

Originally Posted by nomodsjk

Anyone know if my zspeed under Shroud will still fit? I love that thing and for 200$ you can't beat it. It comes with a removable pannel for oil changes

Originally Posted by pfdaxe

Needed some trimming on the inside because of my oil cooler. They have about a 4"x4" opening for the drain plug, but with my adapter plate and larger filter, I'll have to make a larger opening. The FRP cuts like butter. I also have to move my HID fogs in a bit to clear the opening.

Originally Posted by equalme

Did anybody fit their own amuse front bumper? If so, just curious if you had to trim the fender lining at all...I'm having a hell of a time getting the AJ bumper on.

Originally Posted by simota1

for the front bumper.... you will have to CUT the oem splash guards so the bumper will fit.... you do this even with the real kit so no worries... now the hard part is that on the front diffuser part... the holes dont line up at all..... none of them do... so you will have to dremel new holes so that you can put the bolts in the factory parts

Originally Posted by FairladyZ10PG

How are other amuse owners changing their oil? I can't jack up my car without having to remove the sideskirts. Just trying to get ideas since I can't fit my jack under the car even with the home made wooden ramps (not high enough).

Originally Posted by axmea?

Its a hot mess with these skirts. You need two low profile jacks from harbor freight and four stands to do it right or take it to a local shop like I do.

Originally Posted by definitionxmk

i roll up on some wood. jack it up w more wood touching the jack and the frame, then put the jack stand. i then jack up the other side and the same way to level it out. then i have to take off the whole front bumper to get to the oil filter (oil filter relocation kit). it sucks.

Originally Posted by simota1

for the amuse side .... i assume its from shine... if it is... then no mods needed... they fit really nice.... remove the stock one by unbolting the 8 10mm bolts under the car the screws in the front portion in back of the tire and the ones in the rear tire located in front of it... pull the upper portion of the side skirt to release the tabs and take out the double stick mounting tape.. then slide it forward and voila install the new ones....

Originally Posted by KaienZ34

From my bro simota...

AMUSE SIDE SKIRTS INSTALL!!!!


alright man.... LOL its like 2am here but i gotta at least finish this one.... here is the fun part... your gonna have to drill.... reason being the side skirts that carbon signal provides you has no holes whatsoever but before you freak out.... its actually really easy

step one...

man i wish i took pictures lol ok... there are two screws phillip heads... in the front of the rear tire.... and one phillip head in the front... which is located in the back of the front tire..... i find it easier to jack up the car at its jack points so there is plenty of room to work with.... you have to remove the rear tire.... unscrew the two screws in the back and the one in the front

step two

un bolt all of the 10mm bolts located underneath the stock side skirt... there is maybe like 8 if im not mistaken.... and one pop in fastener.... remove all of that... here is the tricky part... when you open the door... the immediate curve where the body and side skirt meets in the door jam there is double stick tape there.... just pull on it and break the seal of the mounting tape....now you have to pull towards you until you hear a small snap... which means you unlocked the clips.... id say a good 4-5 inches around the mounting tape area..... thats how much you pull forward... no more than that or else youll snap the clips.... now once it is forward.... you have to push towards the front of your car... this will unlock the remainder of all the clips holding the side skirt repeat the step on the pass and your all set

step three

get the carbon signal side skirts... and look at it.... you will see little places where there should have been a hole.... pay close attention to them you can easily tell because the finish on that part is rough and a circle outline is there... now you have to drill precisely all those holes out.... and youll never guess what... they bolt up precisely..... the clips that was on you stock side skirts are useless.... they wont mount on your amuse skirts.... all you have to do is add mounting tape where you removed it and bolt up all the 10mm underneath and your all set.... put back the phillip screws in the rear and the front
remount your rear tire unjack your z... and do it on the other side

step four

step back grab a beer and now sir you have the rear and side skirts mounted....

Originally Posted by GaleForce

Also, the side skirts, just behind the doors where it meets the body (the horizontal line) will need to be brought out a little to meet up nicely with the existing body. Other than that, the fitment is pretty good.

Originally Posted by CarbonSignal

For rear Amuse bumper you need to create some kind of bracket for license plate lights that dont think can be done at home as DIY

Originally Posted by Ire

what does everyone do about the white foam that peeks through the mesh on the rear? Im thinking of just getting some black wrap and sticking it over the white. either that or plastidipping it.

Originally Posted by wheee!

Going to 'carve' mine down a bit for more clearance and paint it black....

Originally Posted by Realale

I just removed it altogether. You would have to shave it down so thin I really don't think it would do anything.

Originally Posted by wheee!

I agree now after looking at it again tonight. It's going to stay off the car and the bumper fits better too.

Originally Posted by simota1

one more thing fellas... im having a problem with my oem exhaust making contact with my amuse rear.... im scared it'll lead to a crack soon.... i just noticed it today...

Originally Posted by simota1

so after looking at my rear bumper there is definitely pressure....... its pushing my amuse bumper 1/2" forward im scared it'll crack it when i drive it

Originally Posted by cooltoy

The light is for a Toyota Sequoya part number is 81570-42071.

Originally Posted by Riptide67

Been considering the canards. Did you drill an tap them in or 3m?

Originally Posted by pfdaxe

I was on the fence with getting these, but thought I'd try a different look. They came with screws so I drilled from the back prior to putting the bumper on. One note; these are made for Aero Jackets Amuse bumpers. They have a slight curve to them. My shine Auto was flat where these mount. I ended up (after screwing them on) using some black silicone body seam filler to fill in the small gap. It blended in nicely and can't even tell.

Originally Posted by Riptide67

What's everything going to run you with the shipping of the vehicle too? I priced shipping at 1k east to.west and that was only one trip lol.