Nissan rear hamburger sign

kidkotic2001

I want to replace my rear Nissan hamburger sign with a Z one that I am looking at from the Z store. It says that the rear bumper fascia, behind the rear emblem near the left and right edges, are two (one per side) non-critical small "nipples" for positioning of the factory emblem. These can be trimmed before installation simply (a small knife or razor will work fine).

Has anyone done this and are the two nipples the only think that is needed to be removed. The link to the logo is below.


Motorsport! Big "Z" Rear Emblem, Black with Black Carbon Fiber, 09-12 370Z - The Z Store! Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts

__________________
ThAt WaS a CrAzY nIgHt

Trips

By the sounds of it? Yes

It seems like the ones the Z store carries have no guide holes built into them like the stock emblems.

__________________

pbhakta

Yes, once you remove the nissan burger, the only thing you need to remove using a knife are those two dents that stick out to place those emblems since the backing plate is a solid piece.

__________________

kidkotic2001

Cool Beans,

I apologize for adding it to the general section too.

__________________
ThAt WaS a CrAzY nIgHt

Elan

Thinkin about takin my logo off too. How difficult is it to knife away those dents and make it flush? Taking a knife to my car scares me!

__________________
2009 370Z NISMO #477 | AAM Competition Short Tails | AAM Competition HFCs | K&N Typhoon CAI | Kenwood DPX300U | Rockford Fosgate PRIME R300-4 | Rockford Fosgate Punch P165 | Rockford Fosgate Punch P300-12 | Polk Audio db1001 | 15% Tints | GTR Start Button |

Wonka2581

STOP!!!!! Do not take a knife to your car! Use fishing string. And or look up the DIY on it.

__________________
"I have nothing to offer but blood, toil, tears and sweat""Winston Churchill"

logenl7

no way can fishing line or string smooth those bumps out bud.. they're pretty solid pieces of fiberglass. They pretty much have to be chopped off or ground down (small hand held belt grinder / sander)

Wonka2581

Oh I thought he was attempting to take the burger its self off with a knife.

__________________
"I have nothing to offer but blood, toil, tears and sweat""Winston Churchill"

Trips

First off to remove the Emblem?

Use dental floss or fishing string and work the whole perimeter once it's loose enough pull it off, and remove the left over adhesive with goop.

You could use a utility knife or exacto knife to cut the guide out or use a Dremel grinder, And grind it off.

Be very carefully with whatever approach you feel comfortable with .

__________________

kenchan

emblem

Trips

__________________

Elan

I know about the fishing line method! I was just confused about using the knife to cut the bumps. Just curious. I don't even know if I am going to do this as I don't want to over Z it on the rear. (370Z logo, Z vanity plate)

__________________
2009 370Z NISMO #477 | AAM Competition Short Tails | AAM Competition HFCs | K&N Typhoon CAI | Kenwood DPX300U | Rockford Fosgate PRIME R300-4 | Rockford Fosgate Punch P165 | Rockford Fosgate Punch P300-12 | Polk Audio db1001 | 15% Tints | GTR Start Button |

pbhakta

I dont think it over "Z's" it on the back if you get the emblems. I have it and have a z logo on the license plate cover as well and think it still looks good. Like everyone said, fishing line or dental floss to remove the emblem, and then a knife or dremel to grind down the bumps to fit the new emblem on. I actually dremeled mine down but could have easily just used a knife. Trust me its easy and not scary at all, plus even if you mess up a bit, it doesnt matter, no one will see behind the emblems with the backing plate that is on there. As you can see in the pic below all mistakes will be covered up by the emblem.

__________________

gurneyeagle

It helps if you warm the area with a hair dryer to soften the adhesive. Then work the floss behind the badge. At some point, you will be able to lift the badge slowly.

I used a Dremel to knock down the nubs.

Take your time and you won't have any problems.

__________________
Waiting on the Z35! SOLD - 2011 Gun Metallic Touring 7AT w Sports Pkg & Nav, Nismo Bumper and Rims, RC Grille, RC Brake Ducts, H&R Spacers, Painted Door Hdls, GTR Start Button, Nav By-Pass, EVO R Fog Light, CF Ducktail, CF Interior Trim

Elan

You're tempting me even more...that looks great. I think I'm going to do it now.

__________________
2009 370Z NISMO #477 | AAM Competition Short Tails | AAM Competition HFCs | K&N Typhoon CAI | Kenwood DPX300U | Rockford Fosgate PRIME R300-4 | Rockford Fosgate Punch P165 | Rockford Fosgate Punch P300-12 | Polk Audio db1001 | 15% Tints | GTR Start Button |