Mines CF lip Install help!!

BlackZ85 · 06-10-2012, 02:34 AM

So I put on the lip today with 3M double sided tape and screw in 1 bolt on both the bottom corners of the lip which are the only holes that match up to the oem bumper, is that enought to hold the lip while going high speeds? And will the tape comes off if i wash my car alot?

azn370z · 06-10-2012, 02:51 AM

A few bolts up front doesn't hurt. I have a varis lip and I took my z well over the speed limit and it didn't fly off. But a small crack turned into a bigger one from the downforce.

2ndChance · 06-10-2012, 12:51 PM

I always recomend 3M urethane silicone for mounting lips.. it sticks to either FRP CF or PU extremely well, I have a ebay cheap sunline replica lip and went top speed several times, a few bumps, it's still very secured...

But remember it will be hell to take it off later.

BlackZ85 · 06-10-2012, 01:36 PM

there's no where i can put the screws in the front, the only place i can drill a few holes is the back, where the plastic and the lip meets.

that can looks dangerous hahaha, drove around going 45mph and it's still held on good but my heart stops a few time the faster i go, i just want to know what else i can do beside the tape and the 2 screw at the bottom so i don't have to worry about it coming off.

Baer383 · 06-10-2012, 02:15 PM

If you used 3M adhesives promoter pads before you put the double sided tape on then it won't come off.

Automotive Adhesion Promoter Pad 4298

BlackZ85 · 06-10-2012, 03:07 PM

how does that work?, the page doesn't give me much info

Quote:

Originally Posted by Baer383

If you used 3M adhesives promoter pads before you put the double sided tape on then it won't come off.

Automotive Adhesion Promoter Pad 4298

Baer383 · 06-10-2012, 03:21 PM

Quote:

Originally Posted by BlackZ85

how does that work?, the page doesn't give me much info

Just open up the package pull out the small yellow sponge and it all ready has the product on it and wipe it where you want to put the tape.

Note once you stick the tape on you won't be able to pull it back off to reposition it.

BlackZ85 · 06-10-2012, 03:24 PM

will it mess up my paint if i decide to remove the lip in the future?

Baer383 · 06-10-2012, 03:34 PM

Quote:

Originally Posted by BlackZ85

will it mess up my paint if i decide to remove the lip in the future?

yes and no there is a special tool I use at my work to remove taped on pin stripe and left over double sided tape,

3M 07498 Stripe Off Wheel

here it is in action
Toyota Tacoma Eraser Wheel Photo 7

BlackZ85 · 06-10-2012, 03:38 PM

if i go 100mph and it doesn't come off then i'll give it a shot! thanks!

Baer383 · 06-10-2012, 03:42 PM

Quote:

Originally Posted by BlackZ85

if i go 100mph and it doesn't come off then i'll give it a shot! thanks!

N/P

06-10-2012, 02:34 AM	#1 (permalink)
BlackZ85 Enthusiast Member Join Date: Jan 2012 Location: falls church, VA Posts: 321 Drives: 2011 370Z M6/sport Rep Power: 13	Mines CF lip Install help!! So I put on the lip today with 3M double sided tape and screw in 1 bolt on both the bottom corners of the lip which are the only holes that match up to the oem bumper, is that enought to hold the lip while going high speeds? And will the tape comes off if i wash my car alot?

06-10-2012, 02:51 AM	#2 (permalink)
azn370z A True Z Fanatic Join Date: Nov 2008 Location: Seattle Posts: 1,722 Drives: z34 - R1 Rep Power: 490	A few bolts up front doesn't hurt. I have a varis lip and I took my z well over the speed limit and it didn't fly off. But a small crack turned into a bigger one from the downforce. __________________ 2010 k23 H&R sport springs / Spc rear camber arms / SSR SP1 / Berk cbe / Varis cf lip / Nismo S-Tune side skirts

06-10-2012, 02:15 PM	#5 (permalink)
Baer383 A True Z Fanatic Join Date: Aug 2010 Location: Lawrenceville,Ga Posts: 4,293 Drives: My foot up your azz Rep Power: 30	If you used 3M adhesives promoter pads before you put the double sided tape on then it won't come off. Automotive Adhesion Promoter Pad 4298 __________________ 2013 ZL1 754 rwhp 747 rwtq

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
mines front lip+mines air scoops+seibon hood+MCR canadrs on MB Z	zuperman 370	Exterior & Interior	33	04-15-2011 02:32 AM
Mines Lip Molded	370Ztune	Nissan 370Z Photos / Spyshots / Video / Media Gallery	31	11-10-2010 08:20 PM
Mines new ECU	Zsteve	Tuning	16	02-04-2010 09:49 AM
Mines ecu	zrider	Tuning	2	11-19-2009 06:18 PM

06-10-2012, 12:51 PM	#3 (permalink)
2ndChance Base Member Join Date: Feb 2011 Location: Panama Posts: 240 Drives: like he stole it Rep Power: 199	I always recomend 3M urethane silicone for mounting lips.. it sticks to either FRP CF or PU extremely well, I have a ebay cheap sunline replica lip and went top speed several times, a few bumps, it's still very secured... But remember it will be hell to take it off later.

06-10-2012, 01:36 PM	#4 (permalink)
BlackZ85 Enthusiast Member Join Date: Jan 2012 Location: falls church, VA Posts: 321 Drives: 2011 370Z M6/sport Rep Power: 13	there's no where i can put the screws in the front, the only place i can drill a few holes is the back, where the plastic and the lip meets. that can looks dangerous hahaha, drove around going 45mph and it's still held on good but my heart stops a few time the faster i go, i just want to know what else i can do beside the tape and the 2 screw at the bottom so i don't have to worry about it coming off.

06-10-2012, 03:24 PM	#8 (permalink)
BlackZ85 Enthusiast Member Join Date: Jan 2012 Location: falls church, VA Posts: 321 Drives: 2011 370Z M6/sport Rep Power: 13	will it mess up my paint if i decide to remove the lip in the future?

06-10-2012, 03:38 PM	#10 (permalink)
BlackZ85 Enthusiast Member Join Date: Jan 2012 Location: falls church, VA Posts: 321 Drives: 2011 370Z M6/sport Rep Power: 13	if i go 100mph and it doesn't come off then i'll give it a shot! thanks!