*-_-*CarbonSignal Rear Spoiler*-_-*

Wiggins3377

Yeah, make sure you clean any area that will touch the double sided tape well before applying the promotor, then apply the promotor to that same area. You'll need a few packets of it for everything you’ll be installing. Id grab 10 or so just to be safe. You'll also want to test fit the pieces well before applying anything, cause once you use the promotor its near impossible to remove the pieces. I had alot of trouble installing my rear spats simply because of the flex in the bumper. Id suggest taking the whole rear bumper off to install the diffuser. It makes the whole process a lot easier. I’ll post a pic of what I did. As far as paint, id suggest painting the whole thing first, that’s what I did and it turned out fine.

I have the same carbon signal lip and had heard about gap issues as well, however I had mine professional molded to the front bumper. That said I wasn’t made aware of any fitment issues.

__________________
AccuAir/ AirRex/ Amuse/ Bride Japan/ Carbon Fiber Element/ Carbon Signal/ Evo-R/ NRG/ Project Kics/ Samco/ Shine Auto/ SPC/ SPL/ Stance/ Stillen/ Takata/ Top Secret/ Work

Wiggins3377

Here's a pic. I used two saw horses and c clamps to hold it while the spats set.

Attached Images

ImageUploadedByTapatalk1346253433_790423.jpg (174.2 KB, 126 views)

__________________
AccuAir/ AirRex/ Amuse/ Bride Japan/ Carbon Fiber Element/ Carbon Signal/ Evo-R/ NRG/ Project Kics/ Samco/ Shine Auto/ SPC/ SPL/ Stance/ Stillen/ Takata/ Top Secret/ Work

Huan'z

Good job buddy!! I will do what u said. Will post picture when everything in place! Thanks a lot! Where can I get the promoter? Home Depot? Thanks a lot!!

Wiggins3377

I doubt home depot would have it. I also doubt autozone or a similar store would have it. Your best bet would be an automotive paint and supply specialty store. I think amazon has it as well. Like i said, if you need some let me know, there is a place not far from me that has it and i can grab it for you and put it in the mail tomorrow. They typically cost $3-$3.50 a packet.

__________________
AccuAir/ AirRex/ Amuse/ Bride Japan/ Carbon Fiber Element/ Carbon Signal/ Evo-R/ NRG/ Project Kics/ Samco/ Shine Auto/ SPC/ SPL/ Stance/ Stillen/ Takata/ Top Secret/ Work

Huan'z

Thanks for your kindness buddy. But I want to give a try to find some places here so I can do it right away. Got 2 days off this new year. I will pm u right away if I can't find it. Thank u so much!!

Huan'z

I might try duplicolor adhesion promoter. I can get one at advance auto parts near my house for 6.xx a can. What do u think?



Mobile: Buy Duplicolor Adhesion Promoter, Clear, 11 oz. Aerosol CP199 at Advance Auto Parts

Wiggins3377

Looks like that is a paint promoter. I dont think it is the same thing, plus id be concerned about spraying something like that on my car. If its anything like the 3M stuff it’ll leave a white residue which you can’t get off the car. The 3M stuff comes on a sponge and makes application extermely easy.

Whichever route you go you need to test fit and mask the area of the bumper where you don’t want adhesion. I used regular blue painters tape and that worked great.

__________________
AccuAir/ AirRex/ Amuse/ Bride Japan/ Carbon Fiber Element/ Carbon Signal/ Evo-R/ NRG/ Project Kics/ Samco/ Shine Auto/ SPC/ SPL/ Stance/ Stillen/ Takata/ Top Secret/ Work

Huan'z

Yeah u was right. I'm planning to test it on plastic and wait if have the white stuffs. I don't want to repaint my spoiler or bumper. And I also plan to spray on sponge or rug then apply to the area I needed after the test fit and the test of the can. Thanks for the advice buddy. Truly appriciated.