Installed front license plate bracket

AK370Z · 04-11-2009, 12:00 AM

Yup; After getting pulled over by the police, I realized I really don't need any extra attention from the cops. Installation was pretty straight forward. I followed this DIY article by Socal 370Z .

well, since the J-nuts are very thin, I had to go to HomeDepot to pick up some washers and good quality "small length" screws. I also picked up some rubber washers so that I can put it between the bracker and the front bumper. This way if if someone backs into my license plate, my paint won't be scratched. Rubber washers are NOT thin but I used a blade to slice them thin

Here are some pictures:

Please disregard by bent license plate

. I am getting a new plate for the car soon.

BTW, if you have two owner's manual (old and new version), feel free to check the instructions (just for fun) in the old manual . They actually want you to drill again on to the bumper to fasten the bracket. I was like

. That's when I opened the newer manual.

spearfish25 · 04-11-2009, 11:15 AM

Be forewarned to use short length screws. Long screws will dig into your front molding...thanks to my dealer for messing that one up.

trema · 04-11-2009, 12:07 PM

Two things I noticed, because my dealer, evidently, wasn't as careful as I would have hoped.
1) Yes, long screws will damage the front of the car
2) That J-nut is stupid. It's wider than the plate-holder is deep, so it prevents the plate-holder from sitting flush with the front of the car. I need to get ahold of some short screws and different, thinner nuts to hold my plate in place.

AK370Z · 04-11-2009, 03:21 PM

Quote:

Originally Posted by spearfish25

Be forewarned to use short length screws. Long screws will dig into your front molding...thanks to my dealer for messing that one up.

Exactly. That's why I went to HomeDepot to find the shortest length screws and so be safe, used some washers. My screws back end never made out of j-nuts

chibbell · 04-12-2009, 05:11 AM

Not too terrible, but I am trying to get away without one for a while. So far, so good. Though I have had a few cops look at me sideways when Synchro Rev started doing it's thing.

Synchrorev + stop light + cop = unwanted attention

I could just hear them thinking, in the most Southern accent possible, "Son, just what in the sam hell do ya think yer doing?"

trema · 04-12-2009, 12:41 PM

Quote:

Originally Posted by AK370Z

Exactly. That's why I went to HomeDepot to find the shortest length screws and so be safe, used some washers. My screws back end never made out of j-nuts

With the J-nuts clipped in, the mount doesn't sit flush with the front of the car... I wonder what's wrong with mine

AK370Z · 04-12-2009, 12:46 PM

Quote:

Originally Posted by trema

With the J-nuts clipped in, the mount doesn't sit flush with the front of the car... I wonder what's wrong with mine

That's normal. Mine doesn't sit flush either. If you look at the top pictures, you'll see there's no J-nuts installed

Musashi · 04-12-2009, 01:46 PM

Just installed mine. These South Jersey Cops having nothing better to do!

batman_4 · 04-13-2009, 03:15 PM

slap my plate on only when im gonna be traveling out of my city or at night when i know im going to have a beer or two at night.

SOLISIMO · 04-13-2009, 03:30 PM

Florida rocks

spearfish25 · 04-13-2009, 09:31 PM

I used a Dremel to grind down the J-nuts.

keioh · 05-09-2009, 08:11 PM

Quote:

Originally Posted by AK370Z

That's normal. Mine doesn't sit flush either. If you look at the top pictures, you'll see there's no J-nuts installed

I'm just trying to install my front plates. The "J nut" is just too thick in the back and gets in the way for the License Plate Bracket to mount flush with the front bumper.
How did you secure your license plate screws to the Plate Bracket without the J nuts?
Went to the Dealer and the Service dept was closed and other people had no clue.
Any help would be appreciated.

thanks.

AK370Z · 05-10-2009, 11:55 AM

Quote:

Originally Posted by keioh

I'm just trying to install my front plates. The "J nut" is just too thick in the back and gets in the way for the License Plate Bracket to mount flush with the front bumper.
How did you secure your license plate screws to the Plate Bracket without the J nuts?
Went to the Dealer and the Service dept was closed and other people had no clue.
Any help would be appreciated.

thanks.

I did use the j-nuts. The license plate doesn't sit flush when you install them. But it doesn't look too bad. I also put a thin rubber slice so that the end of j-nuts do not rub my paint.

///M-Power · 05-10-2009, 12:36 PM

I'm not sure if you guys are allowed to puncture your plates in the US. But I simply bored holes on my plate where the plate holder screws are positioned and bought longer screws to mount the plate and holder. So plate and holder are held by the same pair of screws.

keioh · 05-11-2009, 12:03 AM

Quote:

Originally Posted by ///M-Power

I'm not sure if you guys are allowed to puncture your plates in the US. But I simply bored holes on my plate where the plate holder screws are positioned and bought longer screws to mount the plate and holder. So plate and holder are held by the same pair of screws.

thats a really good idea. I haven't aligned the plate with the holes but
I think the holes might get in the way of the letters or numbers.

04-11-2009, 12:00 AM	#1 (permalink)
AK370Z Administrator Join Date: Sep 2008 Location: NJ Posts: 9,930 Drives: 09 370Z MB Sports M6 Rep Power: 10	Installed front license plate bracket Yup; After getting pulled over by the police, I realized I really don't need any extra attention from the cops. Installation was pretty straight forward. I followed this DIY article by Socal 370Z . well, since the J-nuts are very thin, I had to go to HomeDepot to pick up some washers and good quality "small length" screws. I also picked up some rubber washers so that I can put it between the bracker and the front bumper. This way if if someone backs into my license plate, my paint won't be scratched. Rubber washers are NOT thin but I used a blade to slice them thin Here are some pictures: Please disregard by bent license plate . I am getting a new plate for the car soon. BTW, if you have two owner's manual (old and new version), feel free to check the instructions (just for fun) in the old manual . They actually want you to drill again on to the bumper to fasten the bracket. I was like . That's when I opened the newer manual. __________________ The370Z Signature Pictures ll Want to rock our forum decals on your car? Then click here! ll How to Embed YouTube Videos In a Post STOP! (Hammertime) ll Become a Premium Member Click HERE ll F.A.Q. Are You a Nissan Dealer? Click Here to Become A "Supporting Dealer" and Start Listing Your 370Zs In Our Inventory Section My Monterey Blue Z ll My Exhaust --> My Intake --> G3 Nissan's Official Response Regarding Oil Temp Issue: CLICK HERE Need a Set of Cheap Winter wheels /Tires? Then Visit The Banner Link Below and Place Your Order. You'll Help Keep The370Z Alive.

04-11-2009, 12:07 PM	#3 (permalink)
trema Base Member Join Date: Jan 2009 Location: Portland, OR Posts: 91 Drives: 09 370z K51 R Rep Power: 596	Two things I noticed, because my dealer, evidently, wasn't as careful as I would have hoped. 1) Yes, long screws will damage the front of the car 2) That J-nut is stupid. It's wider than the plate-holder is deep, so it prevents the plate-holder from sitting flush with the front of the car. I need to get ahold of some short screws and different, thinner nuts to hold my plate in place. __________________ 'Lesca'-2009 370z Touring 6MT w/Sports & Nav- Platinum Graphite/Persimmon. FLO,IKP,SCG,TMA

04-13-2009, 03:15 PM	#9 (permalink)
batman_4 A True Z Fanatic Join Date: Dec 2008 Location: McAllen Tx. Posts: 1,038 Drives: '09 PW 370Z Rep Power: 368	slap my plate on only when im gonna be traveling out of my city or at night when i know im going to have a beer or two at night. __________________ '09 6spd. Touring: Eibach / SPC / Motordyne / Berk / Z1 / Oneighty / Mines / SSR / Stillen / CFE

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Holes in Front Bumper? Question about License Plate Holder	YoungTurk	Nissan 370Z General Discussions	36	01-20-2012 07:22 AM
370Z Led License Plate	abud	Exterior & Interior	25	05-28-2010 11:37 PM
Please put your front license plate on	AK370Z	North East Region	36	08-24-2009 03:30 PM
California License Plate question...	arcticreaver	Nissan 370Z General Discussions	47	03-31-2009 04:16 PM

04-11-2009, 11:15 AM	#2 (permalink)
spearfish25 A True Z Fanatic Join Date: Mar 2009 Location: Naples, FL Posts: 4,117 Drives: to work Rep Power: 1856	Be forewarned to use short length screws. Long screws will dig into your front molding...thanks to my dealer for messing that one up.

04-12-2009, 05:11 AM	#5 (permalink)
chibbell Base Member Join Date: Jan 2009 Location: Portland, OR Age: 44 Posts: 65 Drives: 370z Touring Sport Rep Power: 16	Not too terrible, but I am trying to get away without one for a while. So far, so good. Though I have had a few cops look at me sideways when Synchro Rev started doing it's thing. Synchrorev + stop light + cop = unwanted attention I could just hear them thinking, in the most Southern accent possible, "Son, just what in the sam hell do ya think yer doing?"

04-12-2009, 01:46 PM	#8 (permalink)
Musashi Enthusiast Member Join Date: Mar 2009 Location: New Jersey Posts: 357 Drives: 09 370Z 6speed Rep Power: 606	Just installed mine. These South Jersey Cops having nothing better to do!

04-13-2009, 03:30 PM	#10 (permalink)
SOLISIMO Track Member Join Date: Apr 2009 Location: Florida Posts: 510 Drives: TOP SECRET G37S Rep Power: 17	Florida rocks

04-13-2009, 09:31 PM	#11 (permalink)
spearfish25 A True Z Fanatic Join Date: Mar 2009 Location: Naples, FL Posts: 4,117 Drives: to work Rep Power: 1856	I used a Dremel to grind down the J-nuts.

05-10-2009, 12:36 PM	#14 (permalink)
///M-Power Base Member Join Date: May 2009 Location: Philippines Posts: 9 Drives: 370Z Touring w/ SP Rep Power: 16	I'm not sure if you guys are allowed to puncture your plates in the US. But I simply bored holes on my plate where the plate holder screws are positioned and bought longer screws to mount the plate and holder. So plate and holder are held by the same pair of screws.