For those of you who like lighting

Baer383 · 01-22-2011, 10:07 PM

Quote:

Originally Posted by RockStarKick

Is your main headlight bulb different ? If so what is it ?

No the head light bulb is stock,the only thing thats changed is the 194 marker lamp with a led and the turn signal/parking lamp with a 60 led switch back lamp that is white while the parking lights and or head lights are on then it instantly turns amber when the turn signal is turned on.

Ron · 01-22-2011, 11:08 PM

Quote:

Originally Posted by Baer383

I got them from autolumination,all led replacement of turn signals require resistor or special flashers to avoid hyper flashing,I used 2 6ohm 50 watt resistors one on each side,one side of the resistor goes to the + side of the turn signal and the other side to - side of it.

I've bought from them before, pricey compared to other stores but their bulbs are top notch. Thanks for the info!

DIGItonium · 01-23-2011, 11:32 AM

Looks very nice.... wonder how it looks with my projector turn signal lens

Ron · 01-23-2011, 01:55 PM

Projector turn signal lens? I would like to see that, got a pic?

Baer383 · 01-23-2011, 02:03 PM

Quote:

Originally Posted by DIGItonium

Looks very nice.... wonder how it looks with my projector turn signal lens

?

RockStarKick · 01-23-2011, 02:33 PM

Quote:

Originally Posted by Baer383

No the head light bulb is stock,the only thing thats changed is the 194 marker lamp with a led and the turn signal/parking lamp with a 60 led switch back lamp that is white while the parking lights and or head lights are on then it instantly turns amber when the turn signal is turned on.

Thanks, the reason I was asking is your main headlight bulb has a nice blue tint to it, not too much not too little.

I also have the ordered the 194 parking light led's and am awaiting their arrival.

Not trying to thread jack, but I ordered some 6000K HID bulbs and tried to replace my headlamps the other night. When I installed one of the bulbs, I tested before I reinstalled the fender liner and the bulb flickered and just turned off. I then tried the other bulb with the same result.

Any ideas ?

Here are the bulbs I ordered in 6000K

Morimoto 3Five D2S (35w) - HID Bulbs from The Retrofit Source Inc.

Baer383 · 01-23-2011, 02:41 PM

Quote:

Originally Posted by RockStarKick

Thanks, the reason I was asking is your main headlight bulb has a nice blue tint to it, not too much not too little.

I also have the ordered the 194 parking light led's and am awaiting their arrival.

Not trying to thread jack, but I ordered some 6000K HID bulbs and tried to replace my headlamps the other night. When I installed one of the bulbs, I tested before I reinstalled the fender liner and the bulb flickered and just turned off. I then tried the other bulb with the same result.

Any ideas ?

Here are the bulbs I ordered in 6000K

Morimoto 3Five D2S (35w) - HID Bulbs from The Retrofit Source Inc.

By any chance did you touch the glass part of the bulb with your fingers?

RockStarKick · 01-23-2011, 02:51 PM

Quote:

Originally Posted by Baer383

By any chance did you touch the glass part of the bulb with your fingers?

No, I made sure that I didn't touch them. I have done headlight bulb swaps before. The bulbs also came with some alcohol wipes to wipe bulb before installation... I have no idea what happened. I replaced the stock one and it worked perfectly ??

I was wondering if I was sent the wrong wattage bulbs, would that make a difference ? The packaging didn't say what wattage they were.

Baer383 · 01-23-2011, 02:59 PM

Quote:

Originally Posted by RockStarKick

No, I made sure that I didn't touch them. I have done headlight bulb swaps before. The bulbs also came with some alcohol wipes to wipe bulb before installation... I have no idea what happened. I replaced the stock one and it worked perfectly ??

I was wondering if I was sent the wrong wattage bulbs, would that make a difference ? The packaging didn't say what wattage they were.

Their web site says it is compatible with OEM DS2 if the stock bulbs work then it must be something with there bulbs.

RockStarKick · 01-23-2011, 03:21 PM

Yeah, I am 100% sure it was not installation error. I have already contacted the company and am awaiting a reply. It just sucks, cause it's a real pain to get in there to change the bulb without removing the wheel.

I think I'm just going to wait until I receive all my bulbs so I can do it all at once.

Headlights are looking great on your car !!!

DIGItonium · 01-23-2011, 03:52 PM

Quote:

Originally Posted by Ron

Projector turn signal lens? I would like to see that, got a pic?

I don't know where to get the projector lens (CinCity worked on my headlights). The lens cuts down the depth for the bulbs. I made some triple Luxeon Rebel bulbs, but the bulb was too tall with the heatsink and resistors. Plus, it sat too close to the lens which ruined the diffused look.

Next time, I will ditch the resistors and opt for a BuckToot driver externally wired inline with the turn signal wires. The bulb will end up shorter, so it'll fit nicely.

However, the next time I do any of this stuff I may end up getting another set of headlights and start all over.

Baer383 · 01-23-2011, 03:57 PM

Pretty cool,if I would have known about them I may have bought a set.

DIGItonium · 01-23-2011, 04:02 PM

^ Did you work on your existing set and endured some down time? Also, did you use the heat gun method to separate the housing? I wonder if it's safer than the oven method. My current headlights started to develop some stress cracks, and the paint cracked and is spewing some caramel-like substance near the turn signal.

Baer383 · 01-23-2011, 04:18 PM

Quote:

Originally Posted by DIGItonium

^ Did you work on your existing set and endured some down time? Also, did you use the heat gun method to separate the housing? I wonder if it's safer than the oven method. My current headlights started to develop some stress cracks, and the paint cracked and is spewing some caramel-like substance near the turn signal.

I put them in the oven on a cookie sheet and wet towel heated them up to 250-260 deg for 10 minutes and it came apart,as far as down time I don't drive my car in the winter I work on it so it doesn't really matter how long it takes.One thing that I'm not sure if guys are doing it is to use easy-off oven cleaner(yellow top)to remove the chrome then you have clear plastic to prep and the paint will adhere,my painters at work(I work in a body shop)also used adhesion promoter to make sure the paint has something to stick to.The caramel-like substance is more than likely melted paint.

Ron · 01-23-2011, 04:31 PM

Quote:

Originally Posted by DIGItonium

My current headlights started to develop some stress cracks, and the paint cracked and is spewing some caramel-like substance near the turn signal.

That sucks, heat could have "toasted" the plastic and its showing now. Next time, what about wrapping the whole thing with a wet towel instead of just putting it on the bottom. That should avoid the plastic from receiving direct heat. Just an idea, I haven't tried it. ..Those projectors look very nice!

01-23-2011, 11:32 AM	#18 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 42	Looks very nice.... wonder how it looks with my projector turn signal lens __________________

01-23-2011, 03:21 PM	#25 (permalink)
RockStarKick Enthusiast Member Join Date: Dec 2010 Location: Houston Posts: 298 Drives: it like a rental Rep Power: 14	Yeah, I am 100% sure it was not installation error. I have already contacted the company and am awaiting a reply. It just sucks, cause it's a real pain to get in there to change the bulb without removing the wheel. I think I'm just going to wait until I receive all my bulbs so I can do it all at once. Headlights are looking great on your car !!! __________________ 2013 Mustang GT, 6M, Track Pack & Leather Recaros 2011 Pearl White 6M /Sport Pkg - SOLD

01-23-2011, 03:57 PM	#27 (permalink)
Baer383 A True Z Fanatic Join Date: Aug 2010 Location: Lawrenceville,Ga Posts: 4,293 Drives: My foot up your azz Rep Power: 30	Pretty cool,if I would have known about them I may have bought a set. __________________ 2013 ZL1 754 rwhp 747 rwtq

01-23-2011, 04:02 PM	#28 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 42	^ Did you work on your existing set and endured some down time? Also, did you use the heat gun method to separate the housing? I wonder if it's safer than the oven method. My current headlights started to develop some stress cracks, and the paint cracked and is spewing some caramel-like substance near the turn signal. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
lighting questions	Wronka	DIY Section (Do-It-Yourself)	0	10-25-2010 12:27 AM
Lighting	kannibul	Detailing / Washing / Waxing / Cosmetic Maintenance and Repair	4	05-27-2010 02:15 PM
LED lighting	The BlueMax	Exterior & Interior	27	04-13-2010 12:20 AM
Neon lighting	Osiris	Exterior & Interior	34	05-23-2009 11:26 PM

01-23-2011, 01:55 PM	#19 (permalink)
Ron A True Z Fanatic Join Date: Oct 2010 Location: Houston, TX Posts: 3,009 Drives: TT '11 PW Nismo #113 Rep Power: 21	Projector turn signal lens? I would like to see that, got a pic?