Next Project: GT-R MFD on 370 (oil temp/pressure, boost, etc...)

MotorvateDIY

A while ago, I came across a video that shows a Murano with the GT-Rs MFD (multi-function display)... and that got me going down another rabbit hole



^^^ Notice the" ***"? That indicates a missing sensor/CAN bus data.

As it turns out, the 2010+ NAV units (aka AV control unit) runs the same software and are configured for Nissan vehicles (except GT-R), Infiniti vehicles or GT-R. (with GT-R logo start up screen)

AND there is an undocumented serial terminal (12v UART @ 9600) at the back of the AV unit that can be used to read/write the configuration.

I have purchased an AV unti from ebay and it should be here in a few weeks.

When it arrives:
•I will clone the NAV disk drive. Having a back up copy may be helpful if the NAV drives start to fail in the future and if I mess up, I can put it back to the original config.

• Connect to the serial terminal and see what is available and version number.
• Config it to display the MFD
• Send CAN bus data to the gauges and see if/how they respond

Now, the GT-R has sensors that the G37/370 doesn't (like engine oil pressure, trans oil temp, etc) BUT a "analog sensor to CAN bus module" should work to put the required data on the CAN bus.

Anyways, that's the project goals.

If you want to read more on this, here is the thread at myg37.com:
https://www.myg37.com/forums/audio-v...drive-mod.html

Attached Images

a.jpg (96.2 KB, 407 views)

cv129

Whoa…..wowzzaaa

__________________
Setrab | RE-71 | SPL | JRZ | Nismo | ARK | Whiteline | RacingBrake | CJM Oil Pan | Ti shield

MotorvateDIY

It looks like many 2010+ Nissan and infiniti vehicles that have NAV use the same "AV unit"

They have many different part numbers (25915-xxxxx), but the pinouts from the Clarion service manual show the 370, Murano, Maxima, G37 and GT-R to be the same. It also shows the Nav unit has an unused 5.1 audio output and an unused composite video in.

I can't wait for the AV unit to arrive and start to reverse engineer it!
Estimated delivery is 11 days away

MotorvateDIY

July Update:
While trying to re-program the eBay AV unit, the app crashed and it looks to have bricked the AV unit.
When I start the car, I get the logo splash screen for a looooong time, then a very basic screen for HVAC controls. No radio, no volume, no nav

I now know the boot up is done in hardware and then goes to the hard drive to finish the boot up process.

I have ordered another AV unit and will try not to kill this one

MotorvateDIY

August Update:
I haven't progressed very much, as my "Family & Friends" fleet maintenance has taken most of my free time. However, with most of the work done, I hope to have some progress in the next few weeks.

My $300 box of goodies:


The upper AV unit is the "new" one from a 2013 G37X and the lower one is the bricked AV unit... which I hope to bring back

The LCD screen is the 2010+ (w/Nav) version that has the higher resolution (800 x 480) and uses gigibit video (GVIF) over 2 wires.

The AV modules have been disassembled/reassembled and now I only need to remove 6 screws to swap the 40GB hard drives. (full disassembly requires 50+ screws to be removed!!)

Next step:
Wire it up as a standalone system and try a few things to get the GT-R gauges to display. After that, I can feed the required CAN bus data to get the gauges to function.

Anyways, that's my plan! Wish me luck!

Attached Images

av.jpg (185.0 KB, 307 views)

redondoaveb

Sounds like the mini dash project has taken a back seat

__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo
700+whp

MotorvateDIY

Not at all...
Every time I drive my car, it is plugged in, running and being tested. Overall it is running well.

The next step is to design the final circuit board (now that the semi-conductor shortage is much better!), get the first batch made and offer some for some further testing.

Why so much testing??
I haven't done anything like this before, so I want to make sure it works properly and doesn't cause any vehicle issues.

Last week I picked up a 3D scanner to make it easier to make/print the enclosure.

Soooo, both are progressing as time permits

redondoaveb

Glad to hear that. My Spa Technique dual gauge is acting funky so I either need to replace it with another gauge or wait for your mini dash. I'd rather wait for your mini dash so hopefully testing progresses faster . If you need a 370 to test on, I'm sure I could convince Seb to do the install. I'm primarily looking for fuel pressure, oil pressure, water temp, wideband, boost and I could always throw ethanol content in there and get rid of my Zeitronix gauge too

__________________
Fast Intentions "Stage Seb" twin turbo #098- Specialty Z/Tial-Xonarotor/CJM/Ecutek/HKS/KW/SPL/Hotchkis/Rohana/Toyo
700+whp

MotorvateDIY

November Update:
As time permits, I am still working on trying to get the GTR gauges on the factory NAV screen.

There is a little known "Test Port" on the AV modules. This allows console/terminal/root access.
For this to work, there are a few different things the hardware must do.
To make it easy (almost plug and play) I have developed this:


(The grainy pic is due to the low resolution 3D render, no need to spend extra on a high quality image!)

What does this board do?
• Adds pull up resistor to IT-PC
• Converts the PC-IT 3.3v logic level to 12+ and inverts the signal
• Allows any Mac/PC/Linux serial program (Putty, serial terminal, etc) to connect to the AV unit's serial console, and execute on board commands... and there are a lot of them!

I am currently building the prototype on a perfboard to test/scope voltage levels and waveforms.
If all goes well, I hope to have console access later today.

Attached Images

pcb1s.jpeg (113.6 KB, 246 views)

ZontheRocks

Cool and very interesting. Can’t wait to see final results.

__________________
'16 Pearl White Sport | Stillen Gen. 3 | Motordyne ART | Motordyne Shockwave | ZSpeed | Powertrix | EVO-R | Aeroworkz | Nismo | Z1 | EcuTek | Tuned by Seb @ SpecialtyZ

vtec to vvel

Sub-ed for progression of this. This is unique and interesting indeed.

__________________
Don't like what I post? Too bad. I really don't give a sh!t

MotorvateDIY

Good news... I spend the afternoon testing it and the USB to AV converter works!!




When the AV unit starts up, it displays "xanavi>" and then you can type a command.

Here are the "ver" (version) and "hdd 1 1" command results:




and a list of all the commands that can be used at the console:

btm bcsp xrbt xroem lpavm cwsh cws teld gpshist snr tms xrinit gid dsh hdlxmw hmixmw hvac pmgrdiagn pmgrcamera mgrvcan candiag mgrcan hdlmtr hdltmcair hdltmcsend hdltmc trfe trfs hif refdbg rdset rprt rdbg ipverr navistsreset navistsset ipvreset ipvset self hdlmfd mfd xrdnk aview hmi avm sdl xrcnf xmcu ir xgc1 verall imng wel sql mdc mal xrnt lang dat hdlm atv devs drvs fds oms ldset dor vm onmap trf map rcv vdb aps as asss se ss etcs camera switch rgdv rpf dspctl tol rif hwn rgd rgdc hdm dspset imtest usbrb tel mum vfi lvc hms menu mtrif mtrsd tcp tce tc clw sns xrpo tla hnw dsp obj svr usbmgr hdd ucm acl mgrweb mgrweb adpbtd adp gdicscpu pdicusart sys disc aux dvd audio mec bpss dusa dus ls rm xtp xgpsd xclw xgte xgts xcpl xste xsts xsrad xrsn xrf xfver xrde xrspn xrmfc xrd xrsfl xrmc xrpc cap mgl font xgl mgrbt pmgrestab echo dlp xplsd xgrad iodspi pldck lte lt bpb bps bpc bpa bpp bp pld wdd fcopy call swm mgrmcan acm iodpt iomsgio pmgrspd pmgrgps dspst dspsd pmgradc pdictmu pdicspd pdicscif pdichcan pdicadc i2c iomsgi mcan docan ioltimer ioltime iolring iollist iodev mqsa mqs cs exc exd ex ms d m spyStop spy dbgHelp tt e mRegs l ti so s cret c bdall bd b xcv sca sc prc pw ee es ver oss sas sd promd proms cf co osee oses tshow tr ts i

Next weekend I will add the LCD nav screen, nav buttons and radio/AC buttons to the setup to help with testing.

Oh, one last thing.
During the summer, I used an app to re-program a different AV unit, and it got bricked when the app crashed. *BUT* as it turns out, it isn't bricked, but has a bad configuration that turned off CAN bus communications.

I was able to use the console to send the "restore to factory defaults" and I suspect I can now reprogram it. For a while I thought I just wasted $100.

That's all for now!

Attached Images

	AV700.jpg (220.1 KB, 237 views)
	ver.jpg (88.1 KB, 237 views)

MotorvateDIY

End of November Update

They are AWAKE!

Next step:
Send required CAN bus data for the gauges to display.

Attached Images

GTR_1s.jpeg (223.1 KB, 217 views)

MotorvateDIY

Good news! It is working again.

Unfortunately, I tried multiple things to bring it back and don't know which one did the trick... I'm just happy to have another working NAV unit

MotorvateDIY

Small Update:
For those with navigation, AUX IN audio/video has been figured out!!

I've always wanted to have my phone's maps on the NAV screen as my maps are 10 years old.
The screen is a little blurry due to the low resolution of composite (CSBV) video.

I'll make a plug and play cable and then do some in car testing to determine how functional it is - or isn't.

Attached Images

n_s.jpg (66.5 KB, 192 views)