custom gauges

zpwrgirl · 03-31-2021, 12:45 PM

Hey all!

So, after my fiasco with my gauge needle, I considered doing something a bit different. I'm wanting to change out the tach, speedo and fuel gauge with aftermarket, properly sized versions of themselves. I was told, for the most part, the change would be plug and play. However, I'm going to lose my indicators that are present on the tach. This leads to a question. Is there a way to direct the indicator signals to an outside source or to a separate monitor so I can keep track of them easier, should an issue arise? If not, I could always use an obd2 reader at all times, but I'd prefer a cleaner approach.

Any insight into this would be great, especially if you or someone you know has done similar.

Thanks!

JARblue · 03-31-2021, 01:28 PM

Quote:

Originally Posted by zpwrgirl

I was told, for the most part, the change would be plug and play.

Don't expect it to be

Rusty · 03-31-2021, 03:28 PM

What gauges you planning on going with?

BGTV8 · 03-31-2021, 03:52 PM

Have you looked at the Haltech IC7 dash - I used one in my race car last weekend as my logger dash died and have seen one in a Suby Rex road car and they are awesome .... there is a printed carbon bracket that sits neatly under the OEM instrument panel top .... all driven from the OBDII connection for a road car

I'll hunt for a photo of my car from the weekend and post it here if I can find it.

Hotrodz · 03-31-2021, 04:28 PM

Quote:

Originally Posted by BGTV8

Have you looked at the Haltech IC7 dash - I used one in my race car last weekend as my logger dash died and have seen one in a Suby Rex road car and they are awesome .... there is a printed carbon bracket that sits neatly under the OEM instrument panel top .... all driven from the OBDII connection for a road car

I'll hunt for a photo of my car from the weekend and post it here if I can find it.

Here is a few pictures of mine! Sébastien at Specialty Z is doing the install. Don't have any final pictures yet.

Sent from my SM-G965U using Tapatalk

dts3 · 03-31-2021, 06:18 PM

Who said this would be plug and play? Unless that person was talking about a haltech I would expect it to be a royal pain in the ... As far as the indicators go, I believe that they are all sent on the CAN bus in different messages, so if you're really 'bout that life then you can make a device to monitor the bus and do whatever you want when you see the bits in the messages. I'm not sure if the gauge cluster does this or if it has discrete lines for each indicator, but I do know that you can get at them from the CAN bus.

zpwrgirl · 04-01-2021, 08:22 AM

Quote:

Originally Posted by BGTV8

Have you looked at the Haltech IC7 dash - I used one in my race car last weekend as my logger dash died and have seen one in a Suby Rex road car and they are awesome .... there is a printed carbon bracket that sits neatly under the OEM instrument panel top .... all driven from the OBDII connection for a road car

I'll hunt for a photo of my car from the weekend and post it here if I can find it.

I have considered something like this, but I don't much care for the look. I prefer to keep the original set up but with aftermarket gauges.

zpwrgirl · 04-01-2021, 08:24 AM

Quote:

Originally Posted by Rusty

What gauges you planning on going with?

Not 100% decided on that part yet. I'd like to get an overall gameplan before taking the plunge with that decision. Anyone with gauges close or dead on the same size that we have stock. They need to be color adjustable or blue though as that's what my interior and accents are.

JARblue · 04-01-2021, 08:44 AM

This is probably an easier route for your goals

DIY: Interior LED Color Change

Rusty · 04-01-2021, 09:07 AM

Quote:

Originally Posted by zpwrgirl

Not 100% decided on that part yet. I'd like to get an overall gameplan before taking the plunge with that decision. Anyone with gauges close or dead on the same size that we have stock. They need to be color adjustable or blue though as that's what my interior and accents are.

Speedhut gauges you can custom order. I have the oil pressure, water temp, and diff temp gauges.

https://www.speedhut.com/gauges/

zpwrgirl · 04-01-2021, 03:14 PM

Quote:

Originally Posted by JARblue

This is probably an easier route for your goals

DIY: Interior LED Color Change

I actually wanted to do this immediately after getting the car but waited to save up. Now, with covid, no one around me has time to do it until next year. I'm not horrible per se with soldering, but I'd rather someone that would warranty the part do it.

zpwrgirl · 04-01-2021, 03:18 PM

Quote:

Originally Posted by Rusty

Speedhut gauges you can custom order. I have the oil pressure, water temp, and diff temp gauges.

https://www.speedhut.com/gauges/

I have checked them out before. Unfortunately it seems any gauge I want and like doesn't have the night color I'd want. I'll check them out again to see if anything has changed.

SonicVQ · 04-01-2021, 07:35 PM

Quote:

Originally Posted by dts3

As far as the indicators go, I believe that they are all sent on the CAN bus in different messages, so if you're really 'bout that life then you can make a device to monitor the bus and do whatever you want when you see the bits in the messages. I'm not sure if the gauge cluster does this or if it has discrete lines for each indicator, but I do know that you can get at them from the CAN bus.

Did someone say CAN bus???? That's been my area of research for the last 3 months

(Updated with correction)
The turn signal stalk is wired to the BCM.
When the turn signal stalk is signalling a turn, the BCM flashes the external turn signals and broadcasts a CAN message, that is received by the combination meter/gauge cluster which turns on/off the gauge cluster turn signal.

The CAN ID for the turn signal is 0x60D (BCM), second byte, bit 6 for right turn / bit 5 for left turn.

Hotrodz · 04-01-2021, 08:04 PM

Quote:

Originally Posted by SonicVQ

Did someone say CAN bus???? That's been my area of research for the last 3 months

(Updated with correction)
The turn signal stalk is wired to the BCM.
When the turn signal stalk is signalling a turn, the BCM flashes the external turn signals and broadcasts a CAN message, that is received by the combination meter/gauge cluster which turns on/off the gauge cluster turn signal.

The CAN ID for the turn signal is 0x60D (BCM), second byte, bit 6 for right turn / bit 5 for left turn.

The Haltec is supposed to be plug and play with factory ECU and is what I ordered. I have not talked to Seb about the install yet but I will shortly. Also Austin Hurtle who is on here sparingly but is on Instagram installed one of the AIM dashes and figured out the CAN bus so you may try DM-ing him on Instagram.

Sent from my SM-G965U using Tapatalk

dts3 · 04-02-2021, 01:42 PM

Quote:

Originally Posted by SonicVQ

Did someone say CAN bus???? That's been my area of research for the last 3 months

.

I would like to pick your brain about this. I'll send you a PM

03-31-2021, 12:45 PM	#1 (permalink)
zpwrgirl Base Member Join Date: Feb 2020 Location: Ohio Posts: 28 Drives: 19 370z Black Manual Rep Power: 5	custom gauges Hey all! So, after my fiasco with my gauge needle, I considered doing something a bit different. I'm wanting to change out the tach, speedo and fuel gauge with aftermarket, properly sized versions of themselves. I was told, for the most part, the change would be plug and play. However, I'm going to lose my indicators that are present on the tach. This leads to a question. Is there a way to direct the indicator signals to an outside source or to a separate monitor so I can keep track of them easier, should an issue arise? If not, I could always use an obd2 reader at all times, but I'd prefer a cleaner approach. Any insight into this would be great, especially if you or someone you know has done similar. Thanks!

03-31-2021, 03:28 PM	#3 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,184 Drives: 2011 Nismo GM 6M Rep Power: 2684437	What gauges you planning on going with? __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

03-31-2021, 03:52 PM	#4 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,514 Drives: 09 Nissan 370Z M6 Rep Power: 39973	Have you looked at the Haltech IC7 dash - I used one in my race car last weekend as my logger dash died and have seen one in a Suby Rex road car and they are awesome .... there is a printed carbon bracket that sits neatly under the OEM instrument panel top .... all driven from the OBDII connection for a road car I'll hunt for a photo of my car from the weekend and post it here if I can find it. Hotrodz and zpwrgirl like this.

03-31-2021, 06:18 PM	#6 (permalink)
dts3 Track Member Join Date: May 2018 Location: Farmington Hills, MI Posts: 599 Drives: 08 Expedition Rep Power: 6765	Who said this would be plug and play? Unless that person was talking about a haltech I would expect it to be a royal pain in the ... As far as the indicators go, I believe that they are all sent on the CAN bus in different messages, so if you're really 'bout that life then you can make a device to monitor the bus and do whatever you want when you see the bits in the messages. I'm not sure if the gauge cluster does this or if it has discrete lines for each indicator, but I do know that you can get at them from the CAN bus. JARblue, Rusty and zpwrgirl like this. __________________ Visit my blog! www.LeftoverPi.com

04-01-2021, 08:44 AM	#9 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	This is probably an easier route for your goals DIY: Interior LED Color Change zpwrgirl likes this. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Custom gauge pod with gauges	6mt370	Parts for sale (Private Classifieds)	16	12-01-2016 02:58 PM
Custom Gauges	370Ztune	Exterior & Interior	38	09-14-2016 02:40 PM
Tailor Made: Avant Garde M590 - Custom Fitment, Custom Finishes!	GetYourWheels	Tires/Wheels	3	09-06-2013 01:12 PM
WORK VSXX 20x10 / 20x12 Custom Color Custom Spec ** Clearance PM me !	RavSpec	Tires/Wheels	35	05-31-2013 02:11 PM
GT Motoring - custom tow hook finshing pics, Custom finishes now available	GT Motoring	Exterior & Interior	45	09-05-2010 04:31 AM