Dwight, I would connect it like this:

Pin 2: Accessory Power
Pin 8: Ground (at nearest bolt on the frame)
Pin 6: Power from the nearby switch light
Pin 7: Jumper to pin 8

Pins 2 & 8 will light up the person on the seat when the button is pressed because it will connect pin 2 to pin 3 when pushed. This is connected to accessory power so it will light up anytime you press it (if your key is in ACC or ON). Alternatively, you could connect this to pin 6. Then it will only light up if the your headlights are on when you press it.

Pin 6 & 8 will light up the text whenever your other switches are lit up.

If you decided to use this for something. Power will go out pin 3 whenever the button is pushed.

Thanks Brad370. I will order and install the switch.

Passenger Eject Switch - Won't Work
 

Well guys, forget these switches:

OTRATTW :: Switch w/Rocker :: Contura V :: Novelty :: Amber LED :: Lower Independent (Text Area) :: Amber/Amber :: CONTURA V, PASSENGER EJECT, LOWER LED INDEPENDENT

The fore and aft measurements of the rocker are too long to fit in the recessed part of the console where the other switches are. It does fit the hole where the blank switch was, but will not drop down far enough to click into place and allow the switch to rock on and off. It's going back for a refund tomorrow.

i like the make another "pocket/storage area" idea...may just do that :D

I installed garage door openers left and right and the rear fog lamp switch in the middle. The outside switches are momentary rockers and all have custom labels made of white vinyl. We have a cutter here at home for various projects and it came in handy. Attachment 95248

Nismo 40th Anniversary Touring Edition:

http://i.imgur.com/8pZGdLWl.jpg

GJ! :tup: looks great.

I have a Pioneer touchscreen that has usb out of the back. For a quick fix I ran a usb cable from it to the glove box but want to run it to one of those unused switch plates. I think it needs a rubber cover for the usb so it wouldn't get dirt or liquid in it. Anyone know of a usb cable that has one?

Google "USB dust cover" and a wide range of options will come up. Most come in packs of 5 or so.

Where did you buy those switches?

I know this threads a little old. Don't want to beat a dead horse. But has anyone hooked their yaw sensor up to one of these switches. (Completely enable/disable Vdc at the flick of a switch? Or would it be a massive pia?

where did you buy those switches from?

You can find the switches here:

http://www.wiringproducts.com/full-size-rocker-switches

Here's my take on it........ Since I have a different shift knob , I needed a place to display the pattern. Here it is, with a functioning rear fog lite switch.

Yeah, I know the interior is filthy...... One day this week set aside for cleaning.

I use the same switches.
 

My three are:
Left one: Is for auxiliary dash gauges housed in cubby, Oil Pressure, Coolant
temperature.
Center one: Is for the Traction control Gyro Sensor Defeat (Green Wire)
Right one: Is for pump control on the CoolShirt ice cooler while on Track>

3D printed cell phone holder with a charging cable in it.

i went to ebay, rocker switch decals, there are alot of different ones available. mostly marine,some would be whimsical,there were even some for 370zs..surely looks better than the 3 blank ones

USB Charger

After going through this thread and researching I found that Nissan Navara/Patrol buttons will fit from aironboard.com.au
Not cheap but they have a heap of designs. I used the Garage Opener button.

http://www.the370z.com/attachment.ph...1&d=1546923095

http://www.the370z.com/attachment.ph...1&d=1546923095


https://youtu.be/aYU5AxU35pM

I did this as well. Its awesome.
I used this model. Printed in black PLA.
https://www.thingiverse.com/thing:2083528