Swaping out seats question ( juke )

Darkchrix

I want to put my z seats into a juke nismo rs

I want to put those recaro rs seats into my z

I need to give back the juke very fast so i will concentrate to make the z seats fits in the juke first

Is it bolt on ?

Thanks

Zbrah

Juke Nismo RS Recaro Seats

Not a simple pnp due to differences in the brackets.

__________________

Darkchrix

I saw this post already but is there a way tu buy universal brackets to swap them and electric still works?

OTW Z-Boy

Nope and nope

__________________
2014: Nismo 370z #495 Magnetic Black - Stillen Gen3 CAI | SPL F/R Camber Arms | HKS Hypermax IV | JDM Rear Fog Light |GT-R Push Start Button | Z1 2 Piece D/S | Illuminated Kicks | Tommykaira | Work VS-XX BKB Step Lip +23/+13 19" 9.5/11 | Fast Intentions RHFC TDX CBE 12" CF | EcuTek

DeliriousClam

You are **** out of luck

__________________
Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet
MECP Advanced: CEA26671
Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

OhioYJ

Putting the Juke seats into a Z came up in this thread. It appears 2011-nismo-91 has done this, and claims it's not overly difficult? Perhaps this gives you a place to start.

jax4557

Which rental car place will you be returning the juke to?....

NorthStyle

LOL Same exact thing I was thinking. Well, either that or test driving one.

jax4557

Exactly, I'm not mad at the hustle I guess as long as its not a private seller lol...

2011 Nismo#91

To my knowledge no one has done the reverse swap or at least posted any details. Impossible, it shouldnt be too hard. Seats might be a bit low. But you will need to deal with the passenger weight sensor. Either remove it from the juke seats and install it into the Z seats or get the bypass if there is one.

__________________
GTR TT 493Whp/431lbft, Ecutek, Southbend 6puck,Quaife, RPM RollBar 4Point, R888R, JRZ RSPro F(10R/10C) R(10R/6C) 1000f500r inlbs+150inlbs Tender, SPL everywhere.Full Specs

Xplicit97

Juke RS seats are 3" taller than the 370Z seats. As such there is 20 hrs of fabrication work to make the RS Recaros fit into my Nismo 370z. Going in reverse while Im sure is possible, it's anything but a direct swap. Cutting and welding will be necessary for both swaps. Good luck!

__________________
[B]2011 Brilliant Silver Nismo 370Z # 0305, 15 Nismo wide body conversion, Motordyne E370/Art pipes, Stillen G3, Airlift suspension,20X10 /20X12 Avant Garde F111 forged wheels

Bee370Z

Xplicit97
In 2016 you said:
“For those interested in these seats. I just installed the brackets on mine. No cutting just unbolt the old bracket/sliders, and bolt on the new. I can only speak to the Wedge Engineering brackets and sliders, which cost $417.34 I told them the exact seats they were for. So best I can tell NO cutting or fabrication is needed when using Wedge brackets/sliders.”

Was this not the case? You ended up having to do 20 hrs of fabrication after all?

2011 Nismo#91

With the Wedge brackets it is a bolt in job.*

*It will just barely fit and you will sit much higher in the car.

If you want to sit lower you will need to cut and weld parts of the seat and/or brackets which will take time. I think the non sliding bracket is lower but you would have to call Wedge to confirm.

The passenger weight sensor from the Juke seats don't connect to the Z. So you would need to either swap the weight sensors or install a bypass ~$90 that fools it to thinking there is always someone in the seat and you would need to have the seat buckled because otherwise the fasten seat-belt light would always be on.

__________________
GTR TT 493Whp/431lbft, Ecutek, Southbend 6puck,Quaife, RPM RollBar 4Point, R888R, JRZ RSPro F(10R/10C) R(10R/6C) 1000f500r inlbs+150inlbs Tender, SPL everywhere.Full Specs

Bee370Z

When you say it will barely fit and you will sit much higher with the Wedge Brackets. Are you using the Recaro seat subframes? Or the standard subframes that came on the Juke?

The Recaro subframes are extremely low profile, so I’m trying to imagine how tall the wedge adapter would have to be to create that issue.

Bee370Z

This is with the low profile subframe:

6B47D8DA-07FB-4E55-9477-09CAF1005A35.jpg

40250867-436F-4808-B921-E9938404B572.jpg