Heads up about evo r one piece front lip

spiston21 · 04-13-2016, 12:39 AM

So a while back, around early January, I ordered the evo r one piece carbon fiber front lip. I have been insanely busy lately and have not had time to install it until now. I expected slight fitment issues that evo r is known for, but my part didn't fit at all. The curvature of the lip is off and even when you flex it into position the lip is too short to reach the other side... What a disappointment. I will try again tomorrow with a friend and see if we can force it on. absolutely should not have these problems with a 500+ dollar lip. Just wanted to give people a heads up if anyone is looking into buying one.

KrnAndy · 04-13-2016, 05:22 AM

start from the middle not the side.

spiston21 · 04-13-2016, 11:30 AM

Quote:

Originally Posted by KrnAndy

start from the middle not the side.

Did that as well with no success. My last try will be to take off the front bumper

Nixin · 04-13-2016, 03:02 PM

Quote:

Originally Posted by spiston21

Did that as well with no success. My last try will be to take off the front bumper

It shouldn't be this hard. Contact Evo-R and ask for a return authorization and a full credit. Otherwise, have them send out their 'skilled tech' and have him/her put the lip on the Z.

kenchan · 04-13-2016, 03:17 PM

Quote:

Originally Posted by spiston21

So a while back, around early January, I ordered the evo r one piece carbon fiber front lip. I have been insanely busy lately and have not had time to install it until now. I expected slight fitment issues that evo r is known for, but my part didn't fit at all. The curvature of the lip is off and even when you flex it into position the lip is too short to reach the other side... What a disappointment. I will try again tomorrow with a friend and see if we can force it on. absolutely should not have these problems with a 500+ dollar lip. Just wanted to give people a heads up if anyone is looking into buying one.

did u get it wet? ..shrunk?

cooltoy · 04-13-2016, 03:18 PM

Gotta hate the shrinkage factor.

Pearl zed · 04-13-2016, 10:59 PM

Is there a cut off point for sht++y service and performance for vendors that are sponsored/promoted on this forum?
The last 2 out of three experiences have resulted in lies about delivery times by weeks.. they have happily taken my money first then lie about when I will get what I already paid for..

Chuck33079 · 04-13-2016, 11:17 PM

Quote:

Originally Posted by Pearl zed

Is there a cut off point for sht++y service and performance for vendors that are sponsored/promoted on this forum?

The last 2 out of three experiences have resulted in lies about delivery times by weeks.. they have happily taken my money first then lie about when I will get what I already paid for..

That's what evo r does. He's a grade a shitbag. He's been banned here before for this kind of ****.

spiston21 · 04-14-2016, 10:31 AM

Quote:

Originally Posted by Pearl zed

Is there a cut off point for sht++y service and performance for vendors that are sponsored/promoted on this forum?
The last 2 out of three experiences have resulted in lies about delivery times by weeks.. they have happily taken my money first then lie about when I will get what I already paid for..

It took him over a month to ship the lip. The part was "in stock" and he told me he would ship it out within a few days from my order. I had to email him constantly, to which he barely replied to any. His reasoning was that he didn't have a box to ship it in yet...

loiro370z · 04-14-2016, 06:22 PM

Quote:

Originally Posted by Chuck33079

That's what evo r does. He's a grade a shitbag. He's been banned here before for this kind of ****.

sh....y vendor
He told me was gonna send a replacement my fog light,mine got water inside after 7 months
That was on 07-14-2015,still waiting

EVOHUNTER · 04-14-2016, 06:40 PM

Ive always loved his stuff, design and price etc..

But ive never bought anything from him for this reason.

Chinesse made garbage, trying to get service is like pulling teeth..

what a lot of people where saying at one point, was to buy from someone like Z1 who stocks them.

Atleast you know youll get service if theres any issue!

Best of luck!

2011 Nismo#91 · 04-15-2016, 09:05 AM

Yeah I had some issues with another panel vendor before, it's such a low volume thing it is hard to get good service. But parts should fit, no excuse for that.

God-Speed · 04-15-2016, 06:21 PM

Quote:

Originally Posted by 2011 Nismo#91

Yeah I had some issues with another panel vendor before, it's such a low volume thing it is hard to get good service. But parts should fit, no excuse for that.

eastwest2300 · 04-15-2016, 07:38 PM

Damn, and I was debating getting the piece over the tachometer (the crown piece).. I thin I'm gonna pass now.. and his prices are REALLY high... even on eBay..

SOUTHZZ · 04-15-2016, 09:14 PM

Same old evo-r problems.
Without actually seeing the problem with the lip,I can't offer any assistance.
I had a similar deal when I owned a 350z. Ordered a Mines lip from evo-r.
It took forever to get it. When it came in it looked great. However,I had the same
fitment problem. However,with some stretching it poped in.
VERY tight.
Evo-r does have some good stuff.The communications are terrible.
Yes,buy through the Z Store but make sure its in stock.Do not believe,
"expecting it next week..." etc. Won't happen.
The only vendor I know that offers on time/good price carbon fiber is ZCFcovers.
But,ZCF only does smaller covers like B-pillars and interior pieces.I have their rear
license plate backing(see my avatar). Made in the U.S. too.

04-13-2016, 03:18 PM	#6 (permalink)
cooltoy Elite Member Join Date: Jun 2012 Location: Calgary Posts: 13,971 Drives: 14 PW 370Z S/T MT Rep Power: 243722	Gotta hate the shrinkage factor. Mitco39 and Pearl zed like this. __________________ Member of kenchan's "photoshopped mods" and "proper offsets" gang.

04-14-2016, 06:40 PM	#11 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 15	Ive always loved his stuff, design and price etc.. But ive never bought anything from him for this reason. Chinesse made garbage, trying to get service is like pulling teeth.. what a lot of people where saying at one point, was to buy from someone like Z1 who stocks them. Atleast you know youll get service if theres any issue! Best of luck! __________________

04-15-2016, 07:38 PM	#14 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,971 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	Damn, and I was debating getting the piece over the tachometer (the crown piece).. I thin I'm gonna pass now.. and his prices are REALLY high... even on eBay.. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Vq35hr heads and vq37hr heads	Elmo370z	Engine & Drivetrain	2	07-21-2015 11:08 PM
[FOR SALE] EVO-R 3 Piece front lip	flip4life90	Parts for sale (Private Classifieds)	16	06-05-2015 06:46 PM
[WTB] looking for evo r 3 piece front lip	binoy29	Parts for sale (Private Classifieds)	1	05-05-2015 07:56 PM
[FOR SALE] Evo-r front lip kit (3 piece)	Gspinin	Parts for sale (Private Classifieds)	4	05-04-2015 01:55 PM
EVO-R 3 piece front lip vs 1 piece?	Bandit_Kaine	Exterior & Interior	0	08-18-2012 02:23 PM

04-13-2016, 05:22 AM	#2 (permalink)
KrnAndy Base Member Join Date: Feb 2016 Location: Irvine Posts: 112 Drives: 09 Nissan 370z M6 Rep Power: 9	start from the middle not the side.

04-13-2016, 10:59 PM	#7 (permalink)
Pearl zed Base Member Join Date: Nov 2015 Location: Orleans MA Posts: 98 Drives: 19' mt silver sport Rep Power: 9	Is there a cut off point for sht++y service and performance for vendors that are sponsored/promoted on this forum? The last 2 out of three experiences have resulted in lies about delivery times by weeks.. they have happily taken my money first then lie about when I will get what I already paid for..

04-15-2016, 09:05 AM	#12 (permalink)
2011 Nismo#91 A True Z Fanatic Join Date: Mar 2011 Location: NJ Posts: 2,400 Drives: slowly Rep Power: 40569	Yeah I had some issues with another panel vendor before, it's such a low volume thing it is hard to get good service. But parts should fit, no excuse for that.

04-15-2016, 09:14 PM	#15 (permalink)
SOUTHZZ Enthusiast Member Join Date: Jan 2014 Location: ALABAMA Posts: 305 Drives: 09 NISSAN 370Z CS M6 Rep Power: 3400	Same old evo-r problems. Without actually seeing the problem with the lip,I can't offer any assistance. I had a similar deal when I owned a 350z. Ordered a Mines lip from evo-r. It took forever to get it. When it came in it looked great. However,I had the same fitment problem. However,with some stretching it poped in. VERY tight. Evo-r does have some good stuff.The communications are terrible. Yes,buy through the Z Store but make sure its in stock.Do not believe, "expecting it next week..." etc. Won't happen. The only vendor I know that offers on time/good price carbon fiber is ZCFcovers. But,ZCF only does smaller covers like B-pillars and interior pieces.I have their rear license plate backing(see my avatar). Made in the U.S. too.