Motion Lab has all the best power adders from Invidia, HKS, Stillen, M7 and AEM!!

Motion Lab

It is Thursday March 5th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.

Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving.


AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains.

Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU.

AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system.


PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

Motion Lab has all the best power adders from Invidia, HKS, Stillen, M7 and AEM!!

__________________

Motion Lab

It is Wednesday March 11th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technology 370Z Dual 2.5" Exhaust: These days Nissan is making very good OEM exhaust systems leaving very little on the table when it comes to horsepower and torque. Thankfully the team at Berk Technology are experts when it comes making a good exhaust system a great exhaust systems.

Backed by years of experience in building championship winning race cars, Berk Technology has applied the same knowledge into their line of street exhaust systems for the 370Z. The Berk Technology 370Z dual exhaust system was designed from the ground up as a no compromise system that unlocks the potential of the potent Nissan VQ37VHR motor.

Through testing and R&D we discovered the most optimal X-pipe design which is unique to our product. Our design utilizes a tangential siamesed X-pipe design that proved to make the most power on the 370Z and is one of the secrets behind our wide power gains and clean sound. Once you install this system on your 370Z the first thing you'll notice is our signature sound. It will still keep the same sound character of the 370Z, but adds a slightly exotic note that is intoxicating to the automotive enthusiast. Another great benefit is that our systems are tuned to be near silent at cruise and will only come alive during heavier throttle application. There is zero intrusive cabin drone or unpleasant harshness. Vital Stats:

• Dual 2.5" Cat Back with separate muffler systems for left bank & right bank cylinders
• Tangential siamesed X-pipe design unquie to Berk Technology
• Fully stainless steel system: tubing, flanges, mufflers, hangers, & tips
• Uses factory mounting points and installation is 100% bolt on
• Stainless steel flex joints to help eliminate exhaust related NVH
• Fully TIG welded construction for clean and exceptionally strong joints
• Hand assembled by skilled craftsmen
• Average gains of 14-18hp. Berk Technology does NOT inflate dyno numbers!

K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet.



PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Wednesday March 18th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technology 370Z Dual 2.5" Exhaust: These days Nissan is making very good OEM exhaust systems leaving very little on the table when it comes to horsepower and torque. Thankfully the team at Berk Technology are experts when it comes making a good exhaust system a great exhaust systems.

Backed by years of experience in building championship winning race cars, Berk Technology has applied the same knowledge into their line of street exhaust systems for the 370Z. The Berk Technology 370Z dual exhaust system was designed from the ground up as a no compromise system that unlocks the potential of the potent Nissan VQ37VHR motor.

Through testing and R&D we discovered the most optimal X-pipe design which is unique to our product. Our design utilizes a tangential siamesed X-pipe design that proved to make the most power on the 370Z and is one of the secrets behind our wide power gains and clean sound. Once you install this system on your 370Z the first thing you'll notice is our signature sound. It will still keep the same sound character of the 370Z, but adds a slightly exotic note that is intoxicating to the automotive enthusiast. Another great benefit is that our systems are tuned to be near silent at cruise and will only come alive during heavier throttle application. There is zero intrusive cabin drone or unpleasant harshness. Vital Stats:

• Dual 2.5" Cat Back with separate muffler systems for left bank & right bank cylinders
• Tangential siamesed X-pipe design unquie to Berk Technology
• Fully stainless steel system: tubing, flanges, mufflers, hangers, & tips
• Uses factory mounting points and installation is 100% bolt on
• Stainless steel flex joints to help eliminate exhaust related NVH
• Fully TIG welded construction for clean and exceptionally strong joints
• Hand assembled by skilled craftsmen
• Average gains of 14-18hp. Berk Technology does NOT inflate dyno numbers!

K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet.



PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Thursday March 19th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.

Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving.


AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains.

Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU.

AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system.


PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Friday March 20th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.

Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving.


AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains.

Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU.

AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system.


PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Friday March 27th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.

Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving.


AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains.

Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU.

AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system.


PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Thursday April 2nd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Friday April 3rd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Wednesday April 8th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Thursday April 9th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Friday April 10th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Thursday April 16th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Monday April 20th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technology 370Z Dual 2.5" Exhaust: These days Nissan is making very good OEM exhaust systems leaving very little on the table when it comes to horsepower and torque. Thankfully the team at Berk Technology are experts when it comes making a good exhaust system a great exhaust systems.

Backed by years of experience in building championship winning race cars, Berk Technology has applied the same knowledge into their line of street exhaust systems for the 370Z. The Berk Technology 370Z dual exhaust system was designed from the ground up as a no compromise system that unlocks the potential of the potent Nissan VQ37VHR motor.

Through testing and R&D we discovered the most optimal X-pipe design which is unique to our product. Our design utilizes a tangential siamesed X-pipe design that proved to make the most power on the 370Z and is one of the secrets behind our wide power gains and clean sound. Once you install this system on your 370Z the first thing you'll notice is our signature sound. It will still keep the same sound character of the 370Z, but adds a slightly exotic note that is intoxicating to the automotive enthusiast. Another great benefit is that our systems are tuned to be near silent at cruise and will only come alive during heavier throttle application. There is zero intrusive cabin drone or unpleasant harshness. Vital Stats:

• Dual 2.5" Cat Back with separate muffler systems for left bank & right bank cylinders
• Tangential siamesed X-pipe design unquie to Berk Technology
• Fully stainless steel system: tubing, flanges, mufflers, hangers, & tips
• Uses factory mounting points and installation is 100% bolt on
• Stainless steel flex joints to help eliminate exhaust related NVH
• Fully TIG welded construction for clean and exceptionally strong joints
• Hand assembled by skilled craftsmen
• Average gains of 14-18hp. Berk Technology does NOT inflate dyno numbers!

K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet.



PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________

Motion Lab

It is Tuesday April 21st and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.


Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:

• 2009-up 370Z
• 2007-2008 350Z
• 2008-up G37 Coupe
• 2007-up G35 Sedan

M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:

• 60mm exhaust, 76mm collector on the y pipe.
• Full catback exhaust, 304 high grade stainless steel pipes. High quality resonators, mufflers and ADJUSTABLE tips.
• ALL HANDCRAFTED IN JAPAN. true JDM products

PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask!



Thanks for looking!
Alex Goodwin
AlexG@motionlabtuning.com
MotionLabTuning.com - Engineering Performance

__________________