Nissan 370Z Forum  

Few problems on my Z

Hello. I have some issues on my Z and already google it to found someone's thread who had similar problem with me. But, I'm quite not sure what should I

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Engine & Drivetrain


Like Tree2Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 11-14-2014, 01:31 PM   #1 (permalink)
Base Member
 
Join Date: Nov 2014
Location: USA
Posts: 20
Drives: 10 Nissan 370Z
Rep Power: 11
Bluechic is on a distinguished road
Default Few problems on my Z

Hello.

I have some issues on my Z and already google it to found someone's thread who had similar problem with me. But, I'm quite not sure what should I do for it.

So, after driving few miles, a VDC off light comes up and doesn't disappear until engine turn off. I guess, it might occurred because of brake pad, broken sensor or tire&its air pressure. How to figure out the reason?

Second, Sometime, when ignite the engine, it just shut down immediately. It doesn't happen usually but happened.

Third, I can hear some noise that it sounds like grind the iron when I shift the gear. (from lower to upper)

My Z is 2010 and manual transmission with 90k miles. If there is a serious problem, I will bring my Z to Nissan service center to fix it but want to make sure so I can pay the money for it. Thanks.

Last edited by Bluechic; 11-14-2014 at 01:37 PM.
Bluechic is offline   Reply With Quote
Old 11-14-2014, 02:46 PM   #2 (permalink)
Enthusiast Member
 
Join Date: Apr 2014
Location: San Diego
Posts: 443
Drives: 2011 370Z S/T A7
Rep Power: 2901
wanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond repute
Default

Check your battery and take your car to an auto shop and have them run your codes that next time the VDC light comes on. Sounds a bit like you have electrical issues, and it could be caused by many things.

As for the shifting, have you replaced your CSC?
wanker is offline   Reply With Quote
Old 11-14-2014, 03:17 PM   #3 (permalink)
Base Member
 
CMadison's Avatar
 
Join Date: Aug 2013
Location: Lubbock, Tx
Posts: 226
Drives: '12 PW T/S 6MT
Rep Power: 12
CMadison is on a distinguished road
Default

hey, blue, i had the same issue with the traction control light coming on for no reason and wouldn't turn off until i shut off the engine. also, the parking brake light would come on when i was shifting hard at high rpm. these both stemmed from either needing new front brake pads or slightly warped front rotors (i also know this because i had vibrations in the steering wheel when braking from 50+). so, what i just got through doing is i got the front rotors turned and installed new pads. this solved the issue and no more vibrating, either. good luck
__________________
Berk CBE | Berk HFC | Stillen G3 CAI | Uprev | Fujimura | 322 whp
CMadison is offline   Reply With Quote
Old 11-14-2014, 03:43 PM   #4 (permalink)
Premium Member
 
SouthArk370Z's Avatar
 
Join Date: Nov 2010
Location: South Arkansas
Posts: 8,435
Drives: 2014 Challenger
Rep Power: 324198
SouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond repute
Default

Quote:
Originally Posted by Bluechic View Post
...So, after driving few miles, a VDC off light comes up and doesn't disappear until engine turn off. I guess, it might occurred because of brake pad, broken sensor or tire&its air pressure. How to figure out the reason?
Possibly a bad wheel speed sensor. Get the DTC (diag trouble code) from the car using an OBD/CAN scanner while the light is on.

Quote:
Originally Posted by Bluechic View Post
Second, Sometime, when ignite the engine, it just shut down immediately. It doesn't happen usually but happened.
After 90k miles, you probably need to clean the MAFs and throttle bodies.

Quote:
Originally Posted by Bluechic View Post
Third, I can hear some noise that it sounds like grind the iron when I shift the gear. (from lower to upper)
Possibly a synchronizer problem or you may need to change the gear lube.


If you plan on doing you own diagnostics and/or repairs, an OBD/CAN scanner/monitor and the FSM (see link in my sig) are invaluable resources.
__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub
Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma
SouthArk370Z is offline   Reply With Quote
Old 11-14-2014, 04:06 PM   #5 (permalink)
EZT
Track Member
 
EZT's Avatar
 
Join Date: Mar 2011
Location: Gainesville
Posts: 546
Drives: 09 370z
Rep Power: 315
EZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond reputeEZT has a reputation beyond repute
Default

You need to top of your brake fluid is all. Apparently that sensor is quite sensitive. Mine did this and was also just in between max and min, but it certainly would light up my dash until I bought brake fluid.
Jordo! and wsarver like this.
EZT is offline   Reply With Quote
Old 11-14-2014, 05:33 PM   #6 (permalink)
Base Member
 
Join Date: Nov 2014
Location: USA
Posts: 20
Drives: 10 Nissan 370Z
Rep Power: 11
Bluechic is on a distinguished road
Default

Thanks, SouthArk370Z.

I just take my Z to auto shop, probably Nissan service center. I have no idea how to diagnosis for these issues myself. Thanks anyway!
Bluechic is offline   Reply With Quote
Old 11-14-2014, 05:39 PM   #7 (permalink)
Base Member
 
Join Date: Nov 2014
Location: USA
Posts: 20
Drives: 10 Nissan 370Z
Rep Power: 11
Bluechic is on a distinguished road
Default

Thanks for all replies.

wanker, I bought it from dealer and it comes with customized muffler. Anything can be occurred with this? I have the maintenance history from dealer and going to look at it later.

CMadison and EZT, I'm planning to take my Z to auto shop, probably Nissan service center and ask. I think I have to refill the brake fluid up to max before change the brake pad but don't know which one is right for me. So, wondering how much money they going to charge on me to replace the brake pad, refill the brake fluid and solutions for another problems on my Z. Thanks.
Bluechic is offline   Reply With Quote
Old 11-14-2014, 05:42 PM   #8 (permalink)
A True Z Fanatic
 
Jordo!'s Avatar
 
Join Date: May 2010
Location: nirvana
Posts: 6,394
Drives: 2023 NATM
Rep Power: 418
Jordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond reputeJordo! has a reputation beyond repute
Default

Quote:
Originally Posted by Bluechic View Post
a VDC off light and traction light comes up ... my brake fluid and it is between min and max.
As another member noted, that's a very sensitive sensor. Top it off to the max line and that will take care of it.

If it comes back, then there may be a leak, but odds are that will fix it.

That it was down at all suggests the pads might be worn down, so I'd have them checked.

Quote:
Originally Posted by Bluechic View Post
Sometime, when ignite the engine, it just shut down immediately.
That could be clogged air filters (inspect; if no light passes through them, replace or if reusable, clean), a vacuum leak (any stumbling at idle?) or weak battery (have it checked). Fouled plugs are a possibility too, given your mileage.

Quote:
Originally Posted by Bluechic View Post
Third, I can hear some noise that it sounds like grind the iron when I shift the gear. (from lower to upper)
Not sure on that one...

Quote:
Originally Posted by Bluechic View Post
My Z is 2010 and manual transmission with 90k miles.
None of that sounds especially serious, but at 90K a good once over on all the fluids, the belt, the brake pads, spark plugs, air filters, etc would be a good idea.
__________________
Enjoy it. Destroy it.
Jordo! is offline   Reply With Quote
Old 11-14-2014, 05:46 PM   #9 (permalink)
Base Member
 
CMadison's Avatar
 
Join Date: Aug 2013
Location: Lubbock, Tx
Posts: 226
Drives: '12 PW T/S 6MT
Rep Power: 12
CMadison is on a distinguished road
Default

Quote:
Originally Posted by Bluechic View Post
Thanks for all replies.

wanker, I bought it from dealer and it comes with customized muffler. Anything can be occurred with this? I have the maintenance history from dealer and going to look at it later.

CMadison and EZT, I'm planning to take my Z to auto shop, probably Nissan service center and ask. I think I have to refill the brake fluid up to max before change the brake pad but don't know which one is right for me. So, wondering how much money they going to charge on me to replace the brake pad, refill the brake fluid and solutions for another problems on my Z. Thanks.
FYI...changing the brake pads is super easy.
__________________
Berk CBE | Berk HFC | Stillen G3 CAI | Uprev | Fujimura | 322 whp
CMadison is offline   Reply With Quote
Old 11-14-2014, 05:53 PM   #10 (permalink)
Base Member
 
Join Date: Nov 2014
Location: USA
Posts: 20
Drives: 10 Nissan 370Z
Rep Power: 11
Bluechic is on a distinguished road
Default

Thanks Jordo!

So, sum up with all opinions from all youguys,
1. I have to replace my brake pad and rotor for each side of front (not sure for rear side) after refill my brake fluid to fix the VDC and traction light on issue.
2. I also found someone's thread to ask about this issue and one of thing makes it occur is vacuum leak like you mentioned.

So, I want your opinion about my plan. I will take my Z to Nissan service center tomorrow and explain them about this issues, let them take care and also ask the full maintenance too. One thing I worrying is that how much money are they going to charge on me for worst case. I thinking that replace the brake pads, refill brake fluid, replace some parts for vacuum or air filter (I believe my battery is still good enough.) and full maintenance. Do you have any idea?
Bluechic is offline   Reply With Quote
Old 11-14-2014, 05:59 PM   #11 (permalink)
Base Member
 
Join Date: Nov 2014
Location: USA
Posts: 20
Drives: 10 Nissan 370Z
Rep Power: 11
Bluechic is on a distinguished road
Default

CMadison,

As far as I know, I need a jockey and new brake pad(and another stuffs that have to be replaced with brake pad like rotor or etc...). If you can tell me what I need and how to replace it myself, I'd love to do it myself. Thanks.
Bluechic is offline   Reply With Quote
Old 11-15-2014, 01:00 PM   #12 (permalink)
Enthusiast Member
 
Join Date: Apr 2014
Location: San Diego
Posts: 443
Drives: 2011 370Z S/T A7
Rep Power: 2901
wanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond reputewanker has a reputation beyond repute
Default

Quote:
Originally Posted by Bluechic View Post
CMadison,

As far as I know, I need a jockey and new brake pad(and another stuffs that have to be replaced with brake pad like rotor or etc...). If you can tell me what I need and how to replace it myself, I'd love to do it myself. Thanks.
Changing your brake pads and rotors is honestly not difficult with the right tools. You'll need a floor jack, jack stands, socket set/torque wrench, brake cleaner spray etc. Go to any autoparts store tell them what your are doing, and they'll set you up. Also YouTube is full of video tutorials on how to change your brakes.

The first time is a time intimidating, but it's not difficult. It's an important skill to learn and you will save hundreds of dollars working on your own brakes. Good luck.
wanker is offline   Reply With Quote
Old 11-15-2014, 02:47 PM   #13 (permalink)
A True Z Fanatic
 
Read T's Avatar
 
Join Date: May 2012
Location: Raleigh, NC
Posts: 1,046
Drives: 11 Nissan 370z BC 6M
Rep Power: 18
Read T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond reputeRead T has a reputation beyond repute
Default

Also as others have suggested you should get the codes pulled with an OBD scan tool. My Nissan dealership charges $99 for this. Autozone, Advance Autoparts, and O'Reily Autoparts charge $0.
__________________
2011 Nissan 370z Black Cherry Sport Pkg - Daily Driver, , 1960 Morgan +4 fun car, 1986 BMW 325ES, 1998 M3 and 1996 Spec Miata - Race Cars
SUPPORT TEAM WINSOME RACING - WRL, CHUMP, LEMONS
Read T is offline   Reply With Quote
Old 11-16-2014, 05:14 PM   #14 (permalink)
Base Member
 
Join Date: Nov 2014
Location: USA
Posts: 20
Drives: 10 Nissan 370Z
Rep Power: 11
Bluechic is on a distinguished road
Default

Thanks for all to help my issues!

I went Nissan service center yesterday and fix the problem on VDC off and traction light on dashboard. They found leak from master cylinder, fully maintenance and charge on me about $680. Now no more problems on my car. Also, they mentioned that my brake pad is about 50% left and I will fix myself for it next time. Thanks for all and have a great Turkey day!
Bluechic is offline   Reply With Quote
Old 11-17-2014, 12:39 PM   #15 (permalink)
Base Member
 
wsarver's Avatar
 
Join Date: Oct 2013
Location: Tampa, FL
Posts: 115
Drives: 2015 Silverado
Rep Power: 12
wsarver is on a distinguished road
Default

Quote:
Originally Posted by EZT View Post
You need to top of your brake fluid is all. Apparently that sensor is quite sensitive. Mine did this and was also just in between max and min, but it certainly would light up my dash until I bought brake fluid.
Second this. I topped off the reservoir after I flushed the system and no more lights for me.

Glad you got it fixed.

Last edited by wsarver; 11-17-2014 at 12:41 PM. Reason: Maybe I should read...
wsarver is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problems with ecu karlisn Engine & Drivetrain 10 11-07-2014 11:11 PM
Problems... Ni55anPat The Lounge (Off Topic) 3 12-10-2011 01:08 PM
Some problems in my Z Kaiser370z Engine & Drivetrain 8 10-11-2011 02:52 PM
anyone have AC problems yet? ddvette9 Nissan 370Z General Discussions 5 05-30-2011 02:07 AM
Did you have problems with CBE fit? Lee123 Intake/Exhaust 1 06-21-2010 07:16 PM


All times are GMT -5. The time now is 04:52 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2