leaking slight oil from Valve Cover

megalapagas · 07-25-2014, 12:10 PM

Quote:

Originally Posted by 1slow370

the mounts are liquid filled but it doesn't look blown, most likely oil from somewhere else like the fittings or sandwhich plate seals if you have an oil cooler. you might just need to take the filter off and tighten the nut that holds the sandwich plate on.

Edit: also thats not slight oil thats a **** ton of oil

Just saw your post, yea im gonna need to drain it then take off filter and look for those bolts yoir talking about. I had it "proffecially installed" but that was about a year ago though

1slow370 · 07-25-2014, 12:20 PM

Check to make sure the two male an fittings are tight where they go into the aluminum sandwhich plate as well. They are aluminum so dont reef on them but they should be tight. Worse case you would need the two washer seals under those fittings and maybe the face seal under the samich plate.

Sent from my HTCONE using Tapatalk

Plasmite · 07-25-2014, 01:08 PM

I hate those style of fittings, they are notorious for leaking.

Personally , I would wash her down, brake kleen the general area you think the leak is coming from, wipe it down and fire her up while she's on the hoist/ramps and watch close.

SouthArk370Z · 07-25-2014, 01:26 PM

Before buying any parts, I'd try snugging everything up. As mentioned above there is the pipe nipple that holds the adapter plate on. The fittings may need to be loosened, cleaned, and properly tightened. They're pickier than most people realize, especially on the initial install. If over-tightened, the ferrule will not seal properly. Make sure everything is tightened to spec - too tight can be as bad as too loose. If that doesn't fix the leak, then start worrying about replacing parts.

SouthArk370Z · 07-25-2014, 01:56 PM

Quote:

Originally Posted by Plasmite

I hate those style of fittings, they are notorious for leaking.

Personally , I would wash her down, brake kleen the general area you think the leak is coming from, wipe it down and fire her up while she's on the hoist/ramps and watch close.

I like the latter comment; not so much the former.

Edit: I misidentified the connectors, so the following doesn't apply in this case. See 1slow370's comment below. Sorry about that.
The main reason compression tubing fittings fail is because of improper installation - usually over-tightening. A close second is over-tightening during reassembly. Follow the manufacturer's procedure for installing the fittings (usually hand-tight plus 1/8 to 1/2 turn depending on size) and you will have very few leaks. When re-assembling, just snug the nut up - it doesn't have to be as tight as many people think.

1slow370 · 07-25-2014, 02:53 PM

Quote:

Originally Posted by SouthArk370Z

I like the latter comment; not so much the former.

The main reason compression tubing fittings fail is because of improper installation - usually over-tightening. A close second is over-tightening during reassembly. Follow the manufacturer's procedure for installing the fittings (usually hand-tight plus 1/8 to 1/2 turn depending on size) and you will have very few leaks. When re-assembling, just snug the nut up - it doesn't have to be as tight as many people think.

what compression tube fittings? they are an flares, when you take them off put them back on just as tight as a new instal. bad advice is worse than no advice

Sent from my HTCONE using Tapatalk

SouthArk370Z · 07-25-2014, 03:01 PM

Quote:

Originally Posted by 1slow370

what compression tube fittings? they are an flares, when you take them off put them back on just as tight as a new instal. bad advice is worse than no advice

Thanks for straightening that out.

Plasmite · 07-25-2014, 04:20 PM

Quote:

Originally Posted by 1slow370

what compression tube fittings? they are an flares, when you take them off put them back on just as tight as a new instal. bad advice is worse than no advice

Sent from my HTCONE using Tapatalk

Your avatar is broken

1slow370 · 07-25-2014, 05:02 PM

oh and if the leak is coming from the fittings themselves that rarely happens, but it could be that the o-rings in the swivel fittings are worn out. usually doesn't happen but it it can and you would have to replace the leaking fitting. This probably isn't the case but it COULD happen.

1slow370 · 07-25-2014, 05:03 PM

Quote:

Originally Posted by Plasmite

Your avatar is broken

works just fine for me

ReeceZ · 12-01-2016, 11:44 AM

Needing to bring this back up again. My car recently had it's 90 000 kilometer service (or 56k miles). The dealership said they found oil on a spark plug while replacing it as part of the service. They advised that the valve cover gasket needs to be replaced, however, the parts are only set to arrive 3rd week in December. I wanted to know if the vehicle is safe to be driven around until the parts arrive. Thanks

stansens · 12-01-2016, 07:08 PM

Way too much oil as mentioned. Might start with Centre threaded tube that holds sandwich plate onto engine and if it's tight then look into getting a new seal for the plate. If you clean off the oil all around filter and plate you might be able to see where it's leaking with engine running. As you know it should be fixed soon before a failure. Good luck and please post your finding so as to help others. Good luck.

ReeceZ · 12-02-2016, 12:18 AM

Will do, I drove it to work this morning so I'll check for any oil on the ground later. Can't comment on low oil level yet as an oil change was done 2 days ago. However, I did get a faint burning smell which did not last too long, which I'm assuming may be a small bit of oil burning off on the manifold after the engine warmed up. Yesterday afternoon, oil temp gauge reached 95 degrees Celsius (203 Fahrenheit) while in traffic, was not driving hard at all.

Off topic, I also noticed that a clicking sound was coming from the rear when I;
1. Put the car into Drive from Neutral, Park, Reverse
2. Put the car into Reverse from Neutral, Park, Drive
3. Just before the vehicle comes to a complete stop
4. Intermittent on take-off

Thankfully, I was able to find a service bulletin regarding this, was for the 350Z, but still rectified the issue with my car. Link to TSB below

http://s000.tinyupload.com/?file_id=...38939742024398

DOOMMONKEY777 · 12-05-2016, 11:44 AM

there are these paper looking O ring seals that supposed to come with those male adapters or compression steel braded hose connectors, it looks as they r missing in the pic, that's why ur leaking oil, no matter how much you tighten they will always leak.

ReeceZ · 12-12-2016, 01:03 AM

Quote:

Originally Posted by DOOMMONKEY777

there are these paper looking O ring seals that supposed to come with those male adapters or compression steel braded hose connectors, it looks as they r missing in the pic, that's why ur leaking oil, no matter how much you tighten they will always leak.

Parts have not arrived as yet, but I will let the dealership know when I go there again.

07-25-2014, 12:20 PM	#17 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	Check to make sure the two male an fittings are tight where they go into the aluminum sandwhich plate as well. They are aluminum so dont reef on them but they should be tight. Worse case you would need the two washer seals under those fittings and maybe the face seal under the samich plate. Sent from my HTCONE using Tapatalk Plasmite likes this. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

07-25-2014, 01:08 PM	#18 (permalink)
Plasmite Enthusiast Member Join Date: Aug 2012 Location: Canada Posts: 259 Drives: '12 M6 Panty Peeler Rep Power: 13	I hate those style of fittings, they are notorious for leaking. Personally , I would wash her down, brake kleen the general area you think the leak is coming from, wipe it down and fire her up while she's on the hoist/ramps and watch close. Initial Z and B&W_Evader like this. __________________ WISHLIST

07-25-2014, 01:26 PM	#19 (permalink)
SouthArk370Z Premium Member Join Date: Nov 2010 Location: South Arkansas Posts: 8,435 Drives: 2014 Challenger Rep Power: 324198	Before buying any parts, I'd try snugging everything up. As mentioned above there is the pipe nipple that holds the adapter plate on. The fittings may need to be loosened, cleaned, and properly tightened. They're pickier than most people realize, especially on the initial install. If over-tightened, the ferrule will not seal properly. Make sure everything is tightened to spec - too tight can be as bad as too loose. If that doesn't fix the leak, then start worrying about replacing parts. Plasmite likes this. __________________ Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

07-25-2014, 05:02 PM	#24 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	oh and if the leak is coming from the fittings themselves that rarely happens, but it could be that the o-rings in the swivel fittings are worn out. usually doesn't happen but it it can and you would have to replace the leaking fitting. This probably isn't the case but it COULD happen. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

12-02-2016, 12:18 AM	#28 (permalink)
ReeceZ Base Member Join Date: Dec 2013 Location: South Africa Posts: 44 Drives: 370ZR Rep Power: 3367	Will do, I drove it to work this morning so I'll check for any oil on the ground later. Can't comment on low oil level yet as an oil change was done 2 days ago. However, I did get a faint burning smell which did not last too long, which I'm assuming may be a small bit of oil burning off on the manifold after the engine warmed up. Yesterday afternoon, oil temp gauge reached 95 degrees Celsius (203 Fahrenheit) while in traffic, was not driving hard at all. Off topic, I also noticed that a clicking sound was coming from the rear when I; 1. Put the car into Drive from Neutral, Park, Reverse 2. Put the car into Reverse from Neutral, Park, Drive 3. Just before the vehicle comes to a complete stop 4. Intermittent on take-off Thankfully, I was able to find a service bulletin regarding this, was for the 350Z, but still rectified the issue with my car. Link to TSB below http://s000.tinyupload.com/?file_id=...38939742024398 Last edited by ReeceZ; 12-02-2016 at 12:36 AM.

12-01-2016, 11:44 AM	#26 (permalink)
ReeceZ Base Member Join Date: Dec 2013 Location: South Africa Posts: 44 Drives: 370ZR Rep Power: 3367	Needing to bring this back up again. My car recently had it's 90 000 kilometer service (or 56k miles). The dealership said they found oil on a spark plug while replacing it as part of the service. They advised that the valve cover gasket needs to be replaced, however, the parts are only set to arrive 3rd week in December. I wanted to know if the vehicle is safe to be driven around until the parts arrive. Thanks

12-01-2016, 07:08 PM	#27 (permalink)
stansens Base Member Join Date: Nov 2015 Location: toronto, canada Posts: 144 Drives: 2016, 370z Rep Power: 193	Way too much oil as mentioned. Might start with Centre threaded tube that holds sandwich plate onto engine and if it's tight then look into getting a new seal for the plate. If you clean off the oil all around filter and plate you might be able to see where it's leaking with engine running. As you know it should be fixed soon before a failure. Good luck and please post your finding so as to help others. Good luck.

12-05-2016, 11:44 AM	#29 (permalink)
DOOMMONKEY777 A True Z Fanatic Join Date: Sep 2010 Location: Crooklyn Posts: 1,011 Drives: 370Z 6psd-sport-pkg Rep Power: 21	there are these paper looking O ring seals that supposed to come with those male adapters or compression steel braded hose connectors, it looks as they r missing in the pic, that's why ur leaking oil, no matter how much you tighten they will always leak. __________________ Kids don't do Drugs, Drugs are bad, so let the professional druggies do Drugs for you. 537whp/496lb/tq@8-9PSI 93 octane Last edited by DOOMMONKEY777; 12-05-2016 at 11:51 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
check engine light.....valve covers leaking?	7speed	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	10	11-03-2013 05:02 PM
Need replace the valve cover. Help needed.	chuan.1992	Engine & Drivetrain	8	03-22-2013 11:06 AM
Radiator Leaking	hazzazi	Mid-Atlantic Region	11	10-11-2011 12:31 PM
Valve cover breathers?	bigrob126	Intake/Exhaust	5	06-24-2011 04:25 PM