400 whp on N/A VQ possible?

.c2 · 06-26-2015, 07:26 PM

Yes, and there's always the problem of different dyno readings lol. Maybe on a dyno that reads much higher than whatever the standard is, 400whp is possible?

On that note, is there a standard dyno that we're supposed to compare numbers to based on what dyno we used? My numbers were done supposedly on a mustang dyno that reads 20% or 30% lower than it's supposed to, and then numbers get recalculated from there buuut I have no idea how accurate it really is

jwick · 06-26-2015, 07:42 PM

Typically the DynoJet is the most consistent.

Elmo370z · 06-26-2015, 08:35 PM

Quote:

Originally Posted by .c2

I have an intake, test pipes, catback, and uprev tune and I'm already at about 340whp. I can imagine that with an intake manifold, headers, and some other bits and pieces with a better tune you can get close to maybe 370whp if you're lucky?

Ecu tek will yeild you more power with its ability to tune the vvel

Elmo370z · 06-26-2015, 08:37 PM

I just need something other than a dry sump to spin the motor to 8,000 rpms. I found heads jun cams and ati damper, waiting on cjm manifold to come out.

1slow370 · 06-27-2015, 08:09 PM

Quote:

Originally Posted by .c2

Yes, and there's always the problem of different dyno readings lol. Maybe on a dyno that reads much higher than whatever the standard is, 400whp is possible?

On that note, is there a standard dyno that we're supposed to compare numbers to based on what dyno we used? My numbers were done supposedly on a mustang dyno that reads 20% or 30% lower than it's supposed to, and then numbers get recalculated from there buuut I have no idea how accurate it really is

mustang dynos running the FACTORY CALIBRATION read lower but the mustang can actually be calibrated to read much higher. the dynojet is locked down as far as the calibration goes.

Elmo370z · 06-27-2015, 11:45 PM

If the parts i need are available ill either take it z1 motorsports or forged performance in GA

synolimit · 06-28-2015, 12:47 PM

Quote:

Originally Posted by .c2

Yes, and there's always the problem of different dyno readings lol. Maybe on a dyno that reads much higher than whatever the standard is, 400whp is possible?

On that note, is there a standard dyno that we're supposed to compare numbers to based on what dyno we used? My numbers were done supposedly on a mustang dyno that reads 20% or 30% lower than it's supposed to, and then numbers get recalculated from there buuut I have no idea how accurate it really is

Yes, dynojet SAE 5th gear, period!

jwick · 06-28-2015, 03:25 PM

Quote:

Originally Posted by Scott@Synergy

Yes, dynojet SAE 5th gear, period!

Most of us turbo guys dyno in 4th. The 5th gear pull is just a glory pull.

synolimit · 06-28-2015, 03:53 PM

Quote:

Originally Posted by jwick

Most of us turbo guys dyno in 4th. The 5th gear pull is just a glory pull.

Most do regardless so they dont pull that fast of a speed but it's not a glory pull; it's the cars 1:1 so if you want to be the most accurate you need it.

jwick · 06-28-2015, 04:49 PM

My car makes more power in 5th than 4th

Jordo! · 06-28-2015, 07:17 PM

4th is less wear and tear on the motor -- you're looking at maybe A few more lbft of tq... 4th is fine.

Compare and contrast in detail here...

synolimit · 06-28-2015, 07:26 PM

Quote:

Originally Posted by jwick

My car makes more power in 5th than 4th

Of course and it should. That's 1:1 ratio. That in SAE is as accurate as you can be. 5th isn't cheating it's just correct.

Here's a cusotmers 4th vs 5th. The 316 vs 324 ones.

jwick · 06-28-2015, 07:44 PM

Quote:

Originally Posted by Scott@Synergy

Of course and it should. That's 1:1 ratio. That in SAE is as accurate as you can be. 5th isn't cheating it's just correct.

Just not a fan of doing 5th gear pulls when it isn't necessary. In no off track, and even then highly unlikely, situation should you be boosting in 5th. You're better off in 4th.

synolimit · 06-28-2015, 07:45 PM

Quote:

Originally Posted by jwick

Just not a fan of doing 5th gear pulls when it isn't necessary. In no off track, and even then highly unlikely, situation should you be boosting in 5th. You're better off in 4th.

I agree. My tuner and most tune 4th then finish one off in 5th. Doing 5th also can be safer because the loads higher so the tunes not as aggressive. This can be better if you're in a real world up hill against wind you don't have to worry as much with knock etc.

Elmo370z · 08-05-2015, 11:23 AM

Just a minor update. Just bought a used long block. It's coming together slowly but surely. Now i can build with the motor out of the car.

06-26-2015, 07:26 PM	#226 (permalink)
.c2 Enthusiast Member Join Date: May 2012 Location: BC Canada Posts: 414 Drives: 09 370z MB 6MT Rep Power: 13	Yes, and there's always the problem of different dyno readings lol. Maybe on a dyno that reads much higher than whatever the standard is, 400whp is possible? On that note, is there a standard dyno that we're supposed to compare numbers to based on what dyno we used? My numbers were done supposedly on a mustang dyno that reads 20% or 30% lower than it's supposed to, and then numbers get recalculated from there buuut I have no idea how accurate it really is __________________ Instagram // Build Thread Amuse / Mines / Bride / Momo / KW / Hotchkis / Motordyne / Invidia / Injen

06-26-2015, 07:42 PM	#227 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	Typically the DynoJet is the most consistent. Jordo! and synolimit like this. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

06-28-2015, 04:49 PM	#235 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	My car makes more power in 5th than 4th __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

06-28-2015, 07:17 PM	#236 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 418	4th is less wear and tear on the motor -- you're looking at maybe A few more lbft of tq... 4th is fine. Compare and contrast in detail here... __________________ Enjoy it. Destroy it.

08-05-2015, 11:23 AM	#240 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	Just a minor update. Just bought a used long block. It's coming together slowly but surely. Now i can build with the motor out of the car. carlitos_370z likes this.

06-26-2015, 08:37 PM	#229 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	I just need something other than a dry sump to spin the motor to 8,000 rpms. I found heads jun cams and ati damper, waiting on cjm manifold to come out.

06-27-2015, 11:45 PM	#231 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	If the parts i need are available ill either take it z1 motorsports or forged performance in GA