NST (NonStopTuning) 370Z VQ37HR Pulley Kit Review w/ Dyno Charts

NonStopTuning

This one deserves an entire book, but here goes...

Q. Will NST Pulleys lead to premature engine failure?

I cover this topic at least several times a month but I don't mind, I understand that your cars are a very large investment for all of you and I prefer that you be intelligent and informed about all your modifications. So here we go again... Please take a few minutes to read everything I have posted here, as I worked hard on trying to give you a good explanation on the topic...

In the past many engines were externally balanced. There was an external balancer attached to the outside of the engine, on the crank snout, used to balance the engine externally. The crank pulley in such engines would then be attached to this balancer. Removal of this balancer is a bad idea. These balancers were most often used on large (8 cyl) V shaped engines of the domestic muscle car era.

Take a look at any modern (1980s and beyond) Honda, Toyota, Nissan, or other japanese engines and you will find no such balancer. These engines are all internally balanced, and this process has improved even further since the late 1990s. So the topic of a BALANCER does not apply here.

What you will find on many modern engines is a harmonic damper. This is a small rubber band literally less than 2mm (less than 1/8th of an inch thick) that is built into the crank pulley. OEM crank pulleys are often called DAMPERS. Try placing an order for a crank pulley at your dealer and your invoice will read damper. This rubber is used to absorb something called NVH, noise/vibration/harshness. Suffice it to say, this rubber is actually not very good at performing its intended purpose after as little as a few thousand miles. What happens to rubber after a couple years of humidity, weather, snow, rain, etc? It often becomes brittle, hard, and crunchy. Can something with these properties actually absorb vibrations very well?

Many many NST customers, including people on your own forums, have reported smoother running engines with NST pulleys. Especially at idle. How is this possible if the rubber is such a vital and super important piece? Perhaps the rubber is not as important as it is cracked up to be?!


Furthermore....


On the topic of the rubber damper, engine vibrations, or possible threats resulting from elimination of this rubber piece...

On a relatively understressed motor with bolt-ons or low amounts of boost like what most of the people on this forum probably run, a solid pulley will not have any life threatening consequences. The factory pulley with a 2mm (less than a 1/8th inch) damper is primarily there for wide band NVH (noise vibration harshness) suppression from the engine and driveline. Removing the damper and replacing it with a solid pulley may lead to minor additional NVH but will not harm the engine. In fact, most people claim their engines seem to run smoother with NST pulleys.

The engineering reasons are that most modern engines have a short, strong crank with, a relatively high natural frequency. The dangerous second harmonic that can cause damage occurs at an rpm that this sort of engine will never see, in the area above 10,000 rpm. Even the stock damper is not tuned for attenuation at this sort of rpm so the argument is somewhat of a moot point.

Now weak engines that are pushing the limit with LOTS of revs, wimpy cranks, super long strokes, lots of boost and dwelling in the upper rpm ranges for long periods of time can benefit from a damper designed to deal with this sort of operation but our engine is not like this, and probably very few people with this motor on this forum push the envelope that hard. How many 500HP + 12,000RPM motors do we have on these forums?

As far as I can tell, our engine has a strong and stiff bottom end that is well built for our intended use. It has an internally balanced crankshaft which is less like to break due to torsional vibration.

There are a lot of Honda, Toyota, and Nissan guys who use underdrive crank pulleys in road racing series like NASA or SCCA. Road racing is much more punishing on an engine than other motorsports. The engine is subjected to run times lasting roughly 30 minutes with the engine always in the upper ranges of its rpm limit. One race weekend is the equivalent of hundreds of 1/4 mile passes. These guys would not use NST pulleys if they were not reliable.

NST sponsors the first ever wheel to wheel Scion tC NASA Road Race car. The same car is also very competitive in the Grand Am and World Challenge series and has factory backing from Toyota, Scion, and TRD. This car has been using pulleys from NST with great results since day one.

NST has sponsored several drift cars participating in the professional US drift series, Fromula Drift and Xtreme Drift Circuit. Several of our cars have also competed in D1 Grand Prix USA and the NOPI Drift series. (I've posted numerous photos of these cars here on this forum and on our website blog.) To make things better, NST products are also used in autocross, time attack, and drag cars. These cars have been using NST pulleys with no issues of any kind for the past few seasons.

We could go on and on...

Is a solid crank pulley harmless to all engines? No it is not. As I said... small, super high reving engines, when modified way past the simple bolt on stages may have problems. These engines reach critical harmonics, past the 10,000 rpm range, an rpm only reached by few RACE engines.

A mildly modded inline six will most likely be fine but one subjected to high rpm (10,000+) for long periods of time (90% of its life) with lots of boost will probably suffer. In this case , the stock balancer/damper is probably not adequate either.

Some of the older american V8 engines are externaly balanced and it is critical not to use a solid hub pulley not designed for these applications, or damage to the engine could result. You will not find solid NST pulleys on our website for such engines.

Our engines and most around here do not fall into the above categories. Rest assured that your engines will not blow up and die or have a reduced life in street and even racing use with these parts.

I would bet that every "expert" that tells you otherwise has little personal, practical, real world experience with the subject; as it applies in your case.

Thanks again everyone, good luck and have fun with all your projects!

__________________
www.NonStopTuning.com
Offering the best in Pulleys, Clutches & Flywheels, Coilovers, and more.
Be sure to keep up with us on the NST blog!

NonStopTuning

And to continue...


NST has been the leader in sport compact pulley development for the past few years and we have many customers with Hondas, Nissans, Toyotas, Lotus, Scion, etc. Please feel free to check the following forums and you will find THOUSANDS of user reviews, comments, and feedback from our customers. You will find that these reviews have consistently been positive...

www. ScionLife .com
www. 8thCivic .com
www. Club4AG .com
www. 86garage .com
www. Houston240sx .com
www. XR-Underground .com
www. MicroImageOnline .com
www. YarisWorld .com
www. USimports .org
etc etc etc


Here are a few specific threads...

the COMPREHENSIVE thread on NST (NonStopTuning) Pulleys - 8th Generation Honda Civic Forum

NST (NonStopTuning) Pulleys. Info, Specs, User Data... - Toyota Yaris Forums - Ultimate Yaris Enthusiast Site

NST CR-Lite Crank Pulley, ALT & WP Kit, Feedback, Reviews, Comments - XR-Underground


Thanks again, good luck and have fun with all your projects everyone!

__________________
www.NonStopTuning.com
Offering the best in Pulleys, Clutches & Flywheels, Coilovers, and more.
Be sure to keep up with us on the NST blog!

christian370z

Sorry to bump this thread up, but should I get both the overdrive alternator pulley and the underdrive crank pulley to get the most benefits? What would be the downside to getting just the underdrive crank pulley?

Trips

Get both, as they are designed to work as a set.

__________________

christian370z

Wow, thanks for the quick response. Would I also need a new drive belt as well or am I fine with my original belt? (The car has 74 miles on it)

Trips

Not necessary, But might as well, the belt I used was the next size smaller to the original belt to take up the small slack, I bought a Gates belt
#K070786. It's not that much about $30 or $40.

Credit to member: Moemeister for the part #

__________________

DuNw/4BanGerZ

I had a '07 Civic Si before I i decided to buy my 370. I had all three pullies (Idler pulley added in order to use stock belt)you offered for it. and I definitely liked the upgrade. Definitely felt a difference in throttle response. I'm Sure I will be satisfied when i buy these.

antivirus6613

Stock belt has way too much slack according to my mechanic and the install requires the fans and a lot of parts to be removed

Trips

My post above adresses the belt issue with a new Gates belt #K070786

__________________

NonStopTuning

Thank you for the recent feedback and comments everyone!

Good luck and have fun with all your projects!!!

__________________
www.NonStopTuning.com
Offering the best in Pulleys, Clutches & Flywheels, Coilovers, and more.
Be sure to keep up with us on the NST blog!

NonStopTuning

Any new pics, comments, reviews from recent customers?!

__________________
www.NonStopTuning.com
Offering the best in Pulleys, Clutches & Flywheels, Coilovers, and more.
Be sure to keep up with us on the NST blog!

bill2k

PMed ya

NonStopTuning

Belt added to our website...
for those who are looking to swap a belt at the time of installation...

NST - The Leader In Nissan 370Z Pulley Development

__________________
www.NonStopTuning.com
Offering the best in Pulleys, Clutches & Flywheels, Coilovers, and more.
Be sure to keep up with us on the NST blog!

Trips

Thats good to see the option Mike, this will make it easier for the new Customers.

__________________

G37sHKS

Anybody know where is NST?

Me and my friends are trying to contact them but no no replay...