Transmission removal and CSC

DIGItonium · 02-07-2013, 10:12 AM

Even after you clean it, the O-ring of the OEM CSC will still deteriorate. I sent Joe the failed OEM CSC for additional analysis. Maybe you can try to rebuild it with new seals.

The first HD-CSC was fine, but there was a thick layer of soot due to clutch disc burning up from rubbing against the flywheel. It was gross, so it necessitated replacement. I went ahead and ordered a new master (first one already failed in Houston after getting the new turbos and clutch kit installed) and HD-CSC. The new transmission had 5th gear issues after a month so they ordered a new one. I figured the new one didn't have much miles so it didn't need replacement.

DR_ · 02-07-2013, 10:12 AM

So did you pull your transmission at your house??

Denny McLain · 02-07-2013, 10:32 AM

Quote:

Originally Posted by DIGItonium

Even after you clean it, the O-ring will still deteriorate. Ask Joe. I sent him my failed OEM CSC for additional analysis.

I seriously doubt that if flushed well. Rubber is not going to deteriorate for the sake of deteriorating if properly cleaned. There was a pretty high rate of failure on factory CSC's and I'm sure if you tore a failed one apart, the O ring might very well be the culprit but that is not a apples to apples comparison.

Denny

Denny McLain · 02-07-2013, 10:33 AM

Quote:

Originally Posted by DR_

So did you pull your transmission at your house??

Yep, and the engine also.

Denny

Joe@ZSpeed · 02-07-2013, 10:52 PM

Quote:

Originally Posted by Denny McLain

I seriously doubt that if flushed well. Rubber is not going to deteriorate for the sake of deteriorating if properly cleaned. There was a pretty high rate of failure on factory CSC's and I'm sure if you tore a failed one apart, the O ring might very well be the culprit but that is not a apples to apples comparison.

Denny

I've torn lots of them apart, Over 50 actually and these are just the ones I received in one piece. A lot of them just break when the release bearing itself breaks off its plastic mount, That's if the seals lasted long enough for this to happen.

If you flushed it out with any kind of solvent you most likely got in on/in the release bearing also which will wash out the grease in it causing the bearing to lock up which spins the entire housing breaking/melting it off the front of the CSC.
Save yourself the trouble and NEVER reuse it, Unless of course you like tow trucks and pulling your trans for fun..

rhd · 02-09-2013, 11:43 AM

Some good info Joe - Thanks

Quote:

Originally Posted by Joe@ZSpeed

I've torn lots of them apart, Over 50 actually and these are just the ones I received in one piece. A lot of them just break when the release bearing itself breaks off its plastic mount, That's if the seals lasted long enough for this to happen.

If you flushed it out with any kind of solvent you most likely got in on/in the release bearing also which will wash out the grease in it causing the bearing to lock up which spins the entire housing breaking/melting it off the front of the CSC.
Save yourself the trouble and NEVER reuse it, Unless of course you like tow trucks and pulling your trans for fun..

02-07-2013, 10:12 AM	#16 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 43	Even after you clean it, the O-ring of the OEM CSC will still deteriorate. I sent Joe the failed OEM CSC for additional analysis. Maybe you can try to rebuild it with new seals. The first HD-CSC was fine, but there was a thick layer of soot due to clutch disc burning up from rubbing against the flywheel. It was gross, so it necessitated replacement. I went ahead and ordered a new master (first one already failed in Houston after getting the new turbos and clutch kit installed) and HD-CSC. The new transmission had 5th gear issues after a month so they ordered a new one. I figured the new one didn't have much miles so it didn't need replacement. __________________ Last edited by DIGItonium; 02-07-2013 at 10:17 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Transmission problem (?) after a transmission fluid change	EWarren	Engine & Drivetrain	7	07-28-2014 11:44 AM
A/C Removal	Sh0velMan	Track / Autocross / Drifting / Dragstrip	2	11-09-2012 11:09 AM
Fender removal	rjsf	Exterior & Interior	9	10-20-2012 05:01 PM
Quick HELP....Hub removal!	spearfish25	Brakes & Suspension	3	04-23-2012 09:48 AM
help with gum removal	thispecialk	Nissan 370Z General Discussions	7	08-05-2009 10:41 AM

02-07-2013, 10:12 AM	#17 (permalink)
DR_ Track Member Join Date: Jul 2009 Location: Dallas Posts: 981 Drives: Touring/Sport M6 PG Rep Power: 17	So did you pull your transmission at your house??