7AT maintenance question

UNKNOWN_370

USE OEM ONLY!!!!!

The nissan tranny's are supersensative to aftermarket oils. These tranny's are specially engineered and any discrepency in the formula may cause adverse reaction to the tranny operation. As stated before the transmissions have a sealed design to keep most non-certified mechanics out. Our tranny oil can run 200k miles but nissan will change it for posterity and insurance, between 100k-120k miles. Higher performance tranny oil upgrades should be discussed with the GT-R specialist at your dealership. I think nissan does make the higher grade oil at a premium. But if you aren't running turbo's? You really don't need it.

PS Redline is recommended on MANUAL TRANS ONLY or as Engine oil for either car

harman.khinda

^ wow thats pretty crazy it can last that long.

Z eliminator

let the dealer change your fluid.

__________________
12.343 @114.14 . 4.5 stroker motor is now being built. Dec 1 2015.

Fern to the Z

Thanks for advice.

__________________
-16 PW/nismO TecH/7AT/Zaktek paint coating/Z1 post-MAF tubes+Side PCV Breather Hose/K&N Drop Ins/F.I. LTH's/ F.I. SS TDX w/12" Resonators-
" I LOVE the SMELL of Headers in the morning!!!!"

gurneyeagle

Repped for an informative post!

__________________
Waiting on the Z35! SOLD - 2011 Gun Metallic Touring 7AT w Sports Pkg & Nav, Nismo Bumper and Rims, RC Grille, RC Brake Ducts, H&R Spacers, Painted Door Hdls, GTR Start Button, Nav By-Pass, EVO R Fog Light, CF Ducktail, CF Interior Trim

harman.khinda

approx how much does a tranny flush cost at the dealer?

jtvq37

Old and probably bought the thread back but.... my transmission blew and i think its because i overheated it... plus it was overfilled... so yes a stock tranny can overheat and blow also because of overfilling! I did not overfill it i meerly watched as he overfilled it because he thought it was ok...

Erob

While I understand the tranny is a sealed unit common sense still applies. Transmission fluid is a lubricant and like all lubricants wear out over time. I had mine replaced at 45000 miles at my local Nissan dealer and have never regretted doing so.

Tractionless

Did my own at 71k when I bought the car 2nd hand. Shifted much better afterward.

__________________
Toys Not Tots

V8Nissan

I change mine at 20k mile intervals. Just did my first change a few months back with 20k on the odometer. The fluid was dark and the 2 magnets were full of metal. It may be true that it has a lifetime fill... If you want it to have a finite life of about 100k miles before shifting issues arise. I drive 25k+ per year so I want it to last.


Alldatadiy.com has the procedure and I have found it online as well. I took the pan off to clean the magnets and pan of debris. While it was off I drilled the pan and Mig welded 2 bungs into the pan. One I have a temperature sensor threaded in to that goes to a tranny fluid temp gauge - part of the fill procedure is having the transmission at 104 degrees fluid temperature. The other I use to fill the pan. The catch is during the final fill when setting the fluid level, the car must be idling in park as you pump fluid in and then let it drain out of the overfill plug. There's a standpipe in the pan and when the fluid is at 104 degrees it is at the correct level when idling in park and no more fluid drains out. The first time I did it I drained the overfill plug at temperature with engine off and I was low on fluid and had some shifting issues until I corrected the level.

So drilling the pan and adding bungs isn't necessary but it's what I wanted for keeping and servicing my car long term. The overfill plug hole is pretty small and you would need to fabricate a special adapter(it is impossible to get one anywhere. I tried, even from overseas) or stick a small hose up past the standpipe to pump fluid in. And the car must be perfectly level while you perform service. As far as reading the temperature I used a trans temp gauge in one of the bungs as well as a harbor freight temperature gun with laser and the two were within a few degrees of each other when taking temp on the bottom of the pan. Also be sure to only use Nissan matic S fluid for servicing.

I am a firm believer in changing automatic transmission fluid. It gets dirty with use. All an automatic transmission is is a bunch of wet clutches and valves. Valves get sticky from metal and clutch debris in the oil and then you have shifting issues. And the Z appears to get very dirty very fast. One other note is that it doesn't have a filter typical of most American cars. It uses a steel mesh screen bolted to the valve body with quite a few bolts

V8Nissan

So without plagiarizing the maintenance manual here is a basic rundown of how to service

Engine off, Drain fluid from pan using rearmost plug on the pan and then replace the plug.

Remove the plug towards the front of the pan and pump fluid into the pan keeping in mind there is a standpipe that is about an inch tall.

Once fluid overflows from the pan or after adding about 3 1/8 quart, reinstall the overfill plug. Run the engine until trans reaches 104 degrees fluid temperature. Also shift into drive and reverse with foot on brake to circulate fluid.

Here you can either drain and service again to flush the fluid or do the final servicing.

For final service ensure you have filled 3 1/8 quart of fluid or until fluid spills from overfill port. With engine RUNNING and fluid temp at 104 degrees remove the overfill plug. When fluid stops dripping it is at the correct level in park. Basically just like servicing any automatic in park, engine running , the difference being you are draining off excess fluid while running instead of using a dipstick.

Also be sure to only use Nissan Matic S fluid. Nothing else

Make sure whatever method you choose to fill the transmission through the overfill port actually works before draining your fluid. Otherwise you will be stuck lol. I have not tried a small piece of hose. My other idea was to purchase a spare overfill plug from Nissan or a bolt with correct thread and crush washer and drill out the middle and then weld some type of fitting to it that you could hook a hose on to. This procedure is probably not a great place to start for the novice mechanic but for a decent mechanic with some ingenuity it can be done fairly easily

Jhill

A small 1/4 in clear nylon hose fits perfect and is stiff enough that it can be shoved in and hold a tight seal.

Tractionless

V8,

I didn't pull the pan when doing mine. How do you reseal? Is there a gasket? If so do you have a part number? Is there a filter once the pan is off that can be replaced? If so do you have a part number?

Thanks

__________________
Toys Not Tots

V8Nissan

Check with "Whatever it takes transmission parts" . They have a website and are great to work with with good quality and low prices. You can look up the transmission and gasket on their site or call. The gasket that came to the local store was great quality. Nice thick and robust unlike the factory paper style gasket. I think it was like $6
As for filter you would have to check with them. The z doesn't have a filter like American cars. Just a steel mesh screen bolted to the valve body with a number of bolts. I didn't change mine but it looked fine. I think it's definitely worth cleaning out the pan there was a lot of sludge and debris.