2012 H20 + Air oil cooler

glenthall · 05-27-2012, 11:19 AM

Quote:

Originally Posted by Jamaica@UAMotorsports

Stillen Oil cooler does work with the 2012. Just need a few extra parts.

Please provide more detail on how

Push370zzz · 02-27-2015, 12:06 PM

Quote:

Originally Posted by martin82

I will be at streets of willow again tomorrow 2012 stock cooler to write down more temps on how it handles. Tomorrow should be warmer so I will see if it goes past 255 before end of each run.

How did it go?

I know I'm a little bit late to the party.

Push370zzz · 02-27-2015, 05:02 PM

Quote:

Originally Posted by Jamaica

Run an additional oil cooler. The 2012 stock wont be enough.

Do you have any numbers relating to this? I believe it is not adequate for serious track use but am wondering if I will be okay for some hot laps. Will I get 10 minutes of track time at a time out of it or am I going to be done after one lap?

GonGo · 07-14-2015, 04:56 PM

I just bought an Z1 Oil Cooler kit with an setrab 25 row, ive had some track time and for extended periods the car will reach 260+ degrees at witch time I go for an cooldown lap.

I would like to see pictures of an "stacked" oil cooler install of 2012+ with oil to coolant and oil to water installed, and would like to know if there is any issue with clearance with the stock oil filter or an optional mobil1 m100.

juld0zer · 08-09-2015, 09:13 AM

You have two choices:
1. Delete the factory water/oil heat exchanger sandwich plate and just join the coolant lines together - but you must fit a thermostatic sandwich plate otherwise your oil takes ages to heat up.
2. Stack/piggyback the external oil cooler on top of the stock heat exchanger by fitting the external cooler system's sandwich plate literally in between the stock unit and the standard size oil filter. It's a tight squeeze from people's reports but it's not impossible. I believe Stillen kits require a specific model oil filter which they outline in the instructions.

How to install z1 sandwich plate on 2012

onzedge · 08-09-2015, 11:58 AM

Quote:

Originally Posted by juld0zer

You have two choices:
1. Delete the factory water/oil heat exchanger sandwich plate and just join the coolant lines together - but you must fit a thermostatic sandwich plate otherwise your oil takes ages to heat up.
2. Stack/piggyback the external oil cooler on top of the stock heat exchanger by fitting the external cooler system's sandwich plate literally in between the stock unit and the standard size oil filter. It's a tight squeeze from people's reports but it's not impossible. I believe Stillen kits require a specific model oil filter which they outline in the instructions.

How to install z1 sandwich plate on 2012

Spooler · 08-09-2015, 01:10 PM

I am dumping the factory cooler for the 2012 and going with a thermostatic mocal plate with a 34 row Setrab oil cooler. Just buy a kit with everything you need. I got mine for F.I. No since in keeping the factory unit, it just heats it up even more.

08-09-2015, 09:13 AM	#20 (permalink)
juld0zer Enthusiast Member Join Date: Nov 2012 Location: Sydney Posts: 428 Drives: 11 Nissan 370Z MB M6 Rep Power: 139	You have two choices: 1. Delete the factory water/oil heat exchanger sandwich plate and just join the coolant lines together - but you must fit a thermostatic sandwich plate otherwise your oil takes ages to heat up. 2. Stack/piggyback the external oil cooler on top of the stock heat exchanger by fitting the external cooler system's sandwich plate literally in between the stock unit and the standard size oil filter. It's a tight squeeze from people's reports but it's not impossible. I believe Stillen kits require a specific model oil filter which they outline in the instructions. How to install z1 sandwich plate on 2012 onzedge likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how does the 2012 factory oil cooler stand up to track/auto x	SiRay6	Track / Autocross / Drifting / Dragstrip	71	12-11-2015 04:53 PM
2012 oil cooler at Willowsprings	martin82	Track / Autocross / Drifting / Dragstrip	26	01-14-2012 09:44 PM
2012 Oil Cooler ?	rxdo	Engine & Drivetrain	7	12-23-2011 02:29 PM
2012 370Z All Models Include Oil Cooler	PJRabbit	Nismo 370Z	49	12-22-2011 08:50 AM
2012 Model Will Have OIl Cooler	jpit	Nissan 370Z General Discussions	150	10-12-2011 10:46 PM

07-14-2015, 04:56 PM	#19 (permalink)
GonGo Base Member Join Date: Mar 2009 Location: Puerto Rico Posts: 80 Drives: 2009 370z PW M6 Rep Power: 16	I just bought an Z1 Oil Cooler kit with an setrab 25 row, ive had some track time and for extended periods the car will reach 260+ degrees at witch time I go for an cooldown lap. I would like to see pictures of an "stacked" oil cooler install of 2012+ with oil to coolant and oil to water installed, and would like to know if there is any issue with clearance with the stock oil filter or an optional mobil1 m100.

08-09-2015, 01:10 PM	#22 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,799 Drives: 2013 Nismo 370z Rep Power: 2684392	I am dumping the factory cooler for the 2012 and going with a thermostatic mocal plate with a 34 row Setrab oil cooler. Just buy a kit with everything you need. I got mine for F.I. No since in keeping the factory unit, it just heats it up even more.