Stillen Underdrive Pulley - Review/Pics/Dyno/Vid

semtex · 05-20-2009, 02:09 PM

Review & Pics:

My friend and I installed the Stillen Underdrive Pulley this past Friday. The installation wasn't too bad overall. It took a total of about one hour, but that includes the time taken to get the car up on jack stands, remove the undertray, etc. The hardest part of the installation was getting the stock pulley off, because they torque the bolt from the factory really, really tight. My mechanic had to hold the starter in place with a pry bar while I loosened the stock pulley bolt with a torque wrench, and it took a lot of effort/strength to loosen that thing. It would have been easier if the car was on a lift, because I would've been able to use my body weight to pull down on the wrench. Doing it while laying on the ground though, I had to rely on muscle alone.

Here's the Stillen UD Pulley, front and rear:

Here's the stock pulley, viewed from underneath the car:

We used a small gear puller slightly modified with one of the arms shortened (we were following wstar's lead on this, so credit goes to him (see wstar's Journal for more details if so desired)):

Stock pulley with the puller attached:

Here's how the engine looks after the stock pulley is removed:

And here's the new pulley, installed:

Driving Impressions:

My butt dyno hasn't noticed any huge gain per se. What is most noticeable to me, however, is that responsiveness has improved, especially off the line. Now, keep in mind that my Z is a 6MT. You know how when you launch off the line there's like a sort of momentary 'dead spot' or 'lag' when you initially engage the throttle and clutch? Well, this is where I notice the most change. That dead spot is virtually gone. My launches feel much more immediate now. The light goes green, I step on the gas and let the clutch out and BAM!! It's on! And I'm not even talking about hard launches. Just with regular around town type of driving, the responsiveness off the line is just more clean and crisp, if that makes any sense.

Also, you know how if you're driving with the AC off and then turn it on, you can actually feel the load the AC is putting on the engine? Like you can feel a bit of power being sucked away. Well, that feeling is noticeably reduced. It's not gone entirely, but it is reduced to a very significant degree.

Dyno:

Okay, enough with the butt dyno. Here's the real thing. I went and put my car back on a DynoJet this morning to see if there are any measurable gains from this thing.

Here's my previous DynoJet dyno:

Here's the updated one:

So peak HP goes up from 324.61whp to 330.23whp (+5.62). Peak torque also went up slightly, but I'd say that the peak torque increase is negligible. What is more significant, torque-wise, is the positive effect this has had on the curve. Compare the old and new torque curves carefully. It looks like I've gained back some of the low-end torque that I lost when I installed the headers. (This would be consistent with my perception of sharper response off the line.) Also, if you look at the top-end, it looks like the torque isn't dropping off as sharply as before! I'm keeping it up longer!!!

As for horsepower, I don't think a gain of 5.62 is half-bad, considering that I've already got the full intake and exhaust mods (i.e., my returns should be diminishing big time by now). All in all, I'm pleased with the results.

Video

YouTube - Stillen 370Z Underdrive Pulley Dyno Results

Don't forget to rep if you found this informative/useful!

Josh@STILLEN · 05-20-2009, 02:28 PM

I'm really disappointed you couldn't find a spectacular bedspread to shoot the product photos on.. boo!

ChrisSlicks · 05-20-2009, 02:31 PM

I don't think you can fairly compare the low end on those charts, the previous dyno runs were started at higher RPM so you just see the spool up lag.

The high end you can see the distinct change, you picked up 10 ft/lbs at red-line which is impressive. Thanks to the reduced falloff you would probably see a benefit from bumping up the red-line slightly.

ssqpolo · 05-20-2009, 02:31 PM

semtex journal is back at NUMERO UNO!! haha. congrats on the install.

LiquidZ · 05-20-2009, 02:53 PM

This is one mod any make of car that nobody dynos individually. Thank you for actually going about and doing it. Its good to see some hardcore proof of gains from an UD pulley.

Thanks man!

semtex · 05-20-2009, 02:56 PM

Quote:

Originally Posted by ChrisSlicks

I don't think you can fairly compare the low end on those charts, the previous dyno runs were started at higher RPM so you just see the spool up lag.

The high end you can see the distinct change, you picked up 10 ft/lbs at red-line which is impressive. Thanks to the reduced falloff you would probably see a benefit from bumping up the red-line slightly.

I'm only comparing the small bit from 2500-3000 rpm. I think it's fair to compare at those points. But prior to 2500 rpm I agree that it's due to the runs starting at different rpms. Having said that, the delta between the two from 2500 - 3000 rpm isn't much. But I'll take what I can get!

wstar · 05-20-2009, 02:56 PM

Nice work man. You'll be hearing from my lawyer shortly re: theft of my patented gear puller modification

semtex · 05-20-2009, 02:58 PM

Quote:

Originally Posted by Josh@STILLEN

I'm really disappointed you couldn't find a spectacular bedspread to shoot the product photos on.. boo!

LOL....hey, I've got a stack of gun magazines for a backdrop this time. Gotta change it up every now and then, you know?

Quote:

Originally Posted by wstar

Nice work man. You'll be hearing from my lawyer shortly re: theft of my patented gear puller modification

HA! I'd better get my checkbook ready for the royalty checks I'm gonna have to write, huh?

ChrisSlicks · 05-20-2009, 03:03 PM

Quote:

Originally Posted by semtex

I'm only comparing the small bit from 2500-3000 rpm. I think it's fair to compare at those points. But prior to 2500 rpm I agree that it's due to the runs starting at different rpms. Having said that, the delta between the two from 2500 - 3000 rpm isn't much. But I'll take what I can get!

Yep, fair enough. Now that you have the software figured out you can overlay the old best run with the new best run to really compare.

SoCal 370Z · 05-20-2009, 03:14 PM

Quote:

Originally Posted by Josh@STILLEN

I'm really disappointed you couldn't find a spectacular bedspread to shoot the product photos on.. boo!

Ditto. Unless Semtex acquiesces and at least throws a cigar magazine into the mix I'll have to stop reading his threads and force him to return my journal.

Skorch · 05-20-2009, 03:16 PM

Thanks for a great writeup. I wonder how the lightweight pulley would compare to the underdrive one in performance. I'm most likely supercharging my Z in the future so an underdrive pulley would be inaptopriate for me.

ZforMe · 05-20-2009, 03:29 PM

Quote:

Originally Posted by Skorch

Thanks for a great writeup. I wonder how the lightweight pulley would compare to the underdrive one in performance. I'm most likely supercharging my Z in the future so an underdrive pulley would be inaptopriate for me.

Skorch, I was wondering the same thing, but have decided I will probably go underdrive for now then swap if the supercharger thing becomes a reality for me. I'm sure the underdrive will be a quick sale to a fellow forum member.

semtex · 05-20-2009, 03:40 PM

Quote:

Originally Posted by SoCal 370Z

Ditto. Unless Semtex acquiesces and at least throws a cigar magazine into the mix I'll have to stop reading his threads and force him to return my journal.

*sigh* Tough crowd. Okay how's this? Surreal enough for you?

phelan · 05-20-2009, 03:46 PM

Quote:

Originally Posted by semtex

*sigh* Tough crowd. Okay how's this? Surreal enough for you?

You, sir, just won every award there is on this forum.

Skorch · 05-20-2009, 03:51 PM

One more question: how has the synchro rev-match responded to the pulley assuming that you have the sports package?

05-20-2009, 02:09 PM	#1 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 32	Stillen Underdrive Pulley - Review/Pics/Dyno/Vid Review & Pics: My friend and I installed the Stillen Underdrive Pulley this past Friday. The installation wasn't too bad overall. It took a total of about one hour, but that includes the time taken to get the car up on jack stands, remove the undertray, etc. The hardest part of the installation was getting the stock pulley off, because they torque the bolt from the factory really, really tight. My mechanic had to hold the starter in place with a pry bar while I loosened the stock pulley bolt with a torque wrench, and it took a lot of effort/strength to loosen that thing. It would have been easier if the car was on a lift, because I would've been able to use my body weight to pull down on the wrench. Doing it while laying on the ground though, I had to rely on muscle alone. Here's the Stillen UD Pulley, front and rear: Here's the stock pulley, viewed from underneath the car: We used a small gear puller slightly modified with one of the arms shortened (we were following wstar's lead on this, so credit goes to him (see wstar's Journal for more details if so desired)): Stock pulley with the puller attached: Here's how the engine looks after the stock pulley is removed: And here's the new pulley, installed: Driving Impressions: My butt dyno hasn't noticed any huge gain per se. What is most noticeable to me, however, is that responsiveness has improved, especially off the line. Now, keep in mind that my Z is a 6MT. You know how when you launch off the line there's like a sort of momentary 'dead spot' or 'lag' when you initially engage the throttle and clutch? Well, this is where I notice the most change. That dead spot is virtually gone. My launches feel much more immediate now. The light goes green, I step on the gas and let the clutch out and BAM!! It's on! And I'm not even talking about hard launches. Just with regular around town type of driving, the responsiveness off the line is just more clean and crisp, if that makes any sense. Also, you know how if you're driving with the AC off and then turn it on, you can actually feel the load the AC is putting on the engine? Like you can feel a bit of power being sucked away. Well, that feeling is noticeably reduced. It's not gone entirely, but it is reduced to a very significant degree. Dyno: Okay, enough with the butt dyno. Here's the real thing. I went and put my car back on a DynoJet this morning to see if there are any measurable gains from this thing. Here's my previous DynoJet dyno: Here's the updated one: So peak HP goes up from 324.61whp to 330.23whp (+5.62). Peak torque also went up slightly, but I'd say that the peak torque increase is negligible. What is more significant, torque-wise, is the positive effect this has had on the curve. Compare the old and new torque curves carefully. It looks like I've gained back some of the low-end torque that I lost when I installed the headers. (This would be consistent with my perception of sharper response off the line.) Also, if you look at the top-end, it looks like the torque isn't dropping off as sharply as before! I'm keeping it up longer!!! As for horsepower, I don't think a gain of 5.62 is half-bad, considering that I've already got the full intake and exhaust mods (i.e., my returns should be diminishing big time by now). All in all, I'm pleased with the results. Video YouTube - Stillen 370Z Underdrive Pulley Dyno Results Don't forget to rep if you found this informative/useful! Spartan 1771, 1st, ortiz73ca and 3 others like this. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

05-20-2009, 02:31 PM	#3 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 653	I don't think you can fairly compare the low end on those charts, the previous dyno runs were started at higher RPM so you just see the spool up lag. The high end you can see the distinct change, you picked up 10 ft/lbs at red-line which is impressive. Thanks to the reduced falloff you would probably see a benefit from bumping up the red-line slightly. 370Zsteve likes this.

05-20-2009, 02:53 PM	#5 (permalink)
LiquidZ A True Z Fanatic Join Date: Nov 2008 Location: Columbus, OH Posts: 1,940 Drives: Mag. Black 2009 370Z Rep Power: 705	This is one mod any make of car that nobody dynos individually. Thank you for actually going about and doing it. Its good to see some hardcore proof of gains from an UD pulley. Thanks man! JCA92 likes this. __________________

05-20-2009, 02:56 PM	#7 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3594	Nice work man. You'll be hearing from my lawyer shortly re: theft of my patented gear puller modification __________________ 7AT Track Car! Journal thread / Car setup details

05-20-2009, 03:16 PM	#11 (permalink)
Skorch Enthusiast Member Join Date: Feb 2009 Location: Phoenix, AZ Posts: 469 Drives: 2012 370Z Rep Power: 540	Thanks for a great writeup. I wonder how the lightweight pulley would compare to the underdrive one in performance. I'm most likely supercharging my Z in the future so an underdrive pulley would be inaptopriate for me. __________________ '12 370Z + Sport \| Stillen Gen3 Intakes \| Stillen UD Pulley \| Motordyne M370 \| FI Exhaust \| FI HFCs \| 4.08 Gears \| Uprev tuned

05-20-2009, 02:28 PM	#2 (permalink)
Josh@STILLEN The370Z.com Sponsor Join Date: Dec 2008 Location: Costa Mesa, CA Posts: 1,197 Drives: 2004 G35 Coupe 6MT Rep Power: 534	I'm really disappointed you couldn't find a spectacular bedspread to shoot the product photos on.. boo!

05-20-2009, 02:31 PM	#4 (permalink)
ssqpolo Track Member Join Date: Jan 2009 Location: Florida Posts: 882 Drives: '12 Black Nismo Rep Power: 267	semtex journal is back at NUMERO UNO!! haha. congrats on the install.

05-20-2009, 03:51 PM	#15 (permalink)
Skorch Enthusiast Member Join Date: Feb 2009 Location: Phoenix, AZ Posts: 469 Drives: 2012 370Z Rep Power: 540	One more question: how has the synchro rev-match responded to the pulley assuming that you have the sports package? __________________ '12 370Z + Sport \| Stillen Gen3 Intakes \| Stillen UD Pulley \| Motordyne M370 \| FI Exhaust \| FI HFCs \| 4.08 Gears \| Uprev tuned

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
STILLEN Longtube G3 Intakes. Review, Dyno and Impressions.	RCZ	Intake/Exhaust	270	06-03-2015 03:25 PM
Stillen Headers installed - Review/Pics/Vid/Dyno	semtex	Intake/Exhaust	120	06-25-2014 01:15 PM
STILLEN lightweight crank pulley	u155282	Engine & Drivetrain	97	08-01-2011 10:33 PM
stillen lightweight crank pulley	black09Z	Engine & Drivetrain	20	04-25-2009 09:00 AM
STILLEN 370Z Underdrive Pulleys Released	Josh@STILLEN	Engine & Drivetrain	38	04-20-2009 02:21 PM